Filtern
Dokumenttyp
- Zeitschriftenartikel (11)
Sprache
- Englisch (11)
Referierte Publikation
- ja (11) (entfernen)
Schlagworte
- SFM/AFM (3)
- EDX (2)
- Interphase (2)
- Surface properties (2)
- AFM (1)
- Adherends (1)
- Antimony sulphide (1)
- Atomic force microscopy (1)
- Copper (1)
- DDS (1)
Scanning force microscopy (SFM) has been used to assess the local mechanical properties of fibre-reinforced polymers. Using a sinusoidal displacement modulation (DM) and lock-in technique the method allows to characterize local viscoelastic properties with a high lateral resolution. The simultaneous measurement of the local electrical conductivity is proposed which facilitates the interpretation of the mechanical data. The investigation of cross-sections perpendicular to the axis of carbon fibres embedded in PPS delivers some information about the change in local stiffness within the interfacial region. As a first approach, assuming a single-exponential decrease in local stiffness along a radial line from fibre to polymer we find characteristic decay lengths which are distributed in a range between 20 and 80nm. Further, a modified DM-mode is proposed which is expected to provide a contrast enhancement of the signal which is related to local stiffness. This can be achieved by installing an additional feedback loop which keeps constant the amplitude of dynamic indentation (CDI-mode).
The physical properties as well as the thickness of the interphase between polymer and reinforcing phase are generally expected to show a strong influence on the macroscopic mechanical properties of composite materials. In this study the scanning force microscope (SFM) has been applied for detecting stiffness gradients near the interface between copper and epoxide. In displacement modulation mode the load exerted by the tip is modulated sinusoidally by vibrating the normal position of the cantilever or the sample. The corresponding amplitude of dynamic cantilever bending is related to local surface stiffness. Thus, using the SFM, the local mechanical properties of the surface under investigation can be probed. When scanning the tip across the reinforcement/polymer interface, the polymeric interphasial zone can be identified with the observed stiffness gradient. For a commercial epoxide based on diglycidyl ether of bisphenol A (DGEBA) cured with an amine-containing hardener, a stiffness gradient was detected that could be fitted by a Gaussian profile typical for diffusional processes. The width of the stiffness gradient was 280 nm. The observation is discussed in terms of interface-induced segregation processes between resin and hardener, as well as heat conduction mechanisms that can occur during the exothermic curing reaction. Both mechanisms are diffusional in nature and, via the local network structure, are expected to show some influence on the local stiffness of the cured epoxy. Copyright © 2000 John Wiley & Sons, Ltd.
Structure formation on the surface of indium phosphide irradiated by femtosecond laser pulses
(2005)
Laser-induced periodic surface structures (LIPSS; ripples) with different spatial characteristics have been observed after irradiation of single-crystalline indium phosphide (c-InP) with multiple linearly polarized femtosecond pulses (130 fs, 800 nm) in air. With an increasing number of pulses per spot, N, up to 100, a characteristic evolution of two different types of ripples has been observed, i.e., (i) the growth of a grating perpendicular to the polarization vector consisting of nearly wavelength-sized periodic lines and (ii), in a specific pulse number regime (N = 530), the additional formation of equally oriented ripples with a spatial period close to half of the laser wavelength. For pulse numbers higher than 50, the formation of micrometer-spaced grooves has been found, which are oriented perpendicular to the ripples. These topographical surface alterations are discussed in the frame of existing LIPSS theories.
This paper focuses on the preparation and characterization of crystalline thin films of rare-earth-doped sesquioxides (Y2O3, Lu2O3) grown by pulsed laser deposition on single-crystal (0001) sapphire substrates. X-ray diffraction measurements show that the films with thicknesses between 1 nm and 500 nm were highly textured along the 111 direction. Using Rutherford backscattering analysis, the correct stoichiometric composition of the films was established. The emission and excitation spectra of europium-doped films with a thickness 100 nm look similar to those of the corresponding crystalline bulk material, whereas films with a thickness 20 nm show a completely different emission behavior.
Stiffness variation in the interphase of amine-cured epoxy adjacent to copper microstructures
(2007)
In an effort to expand the understanding of the mechanical properties of the polymeric interphase on a metal surface, a composite consisting of epoxy and copper was prepared and analyzed. Scanning force microscopy-based force modulation microscopy (SFM-FMM) was employed along with dynamic mechanical analysis (DMA) and energy dispersive X-ray analysis (EDX). Diglycidyl ether of bisphenol A (DGEBA)-based epoxy resins were applied with amine curing agents. The samples were made taking advantage of electron beam lithography (EBL) in order to produce sharp edges of copper structures and a flat surface suitable for the SFM-FMM analysis, which was able to depict the stiffness within the interphase. It is considered significant information because the mechanical characteristic within the narrow interphase was revealed. Comparing with DMA and EDX, the stiffness information of SFM-FMM demonstrated a matching correlation and agreement in terms of preferential adsorption of the curing agent in the vicinity of the interface. The stiffness profiles of the two epoxy systems turned out to be different, and it shows the material dependence of the interphase characteristics.
Laser ablation of single-crystalline indium phosphide (InP) was performed in air by means of linearly polarized Ti : sapphire femtosecond pulses (800 nm, 130 fs, 10 Hz). As a result of the irradiation with a variable number of laser pulses per spot (N /spl les/ 5), several morphological changes (crater formation, rim formation, ripple structures, and cones) were observed. These effects were explored using force modulation microscopy (FMM), a technique based on scanning force microscopy, allowing the simultaneous imaging of both topography and local stiffness at a high lateral resolution. The first laser pulse induces the formation of a protruding rim (height < 20 nm, width /spl ap/ 300 nm) bordering the ablated crater. A Fourier analysis of the multipulse generated topographies reveals the formation of wavelength-sized periodic ripples (modulation depth < 100 nm) with an orientation perpendicular to that of the electric field vector of the laser radiation. Besides these morphological alterations, material modifications were also observed in the irradiated regions by means of the FMM technique. Within the ablated craters, local stiffness variations were found revealing an inhomogeneous material composition/structure as a consequence of the femtosecond pulse laser treatment.
A stoichiometric amineepoxy formulation was cured in the presence of a thermoplastic, namely poly(vinylpyrrolidone) (PVP). The epoxy system consisted of the resin diglycidyl ether of bisphenol A (DGEBA) and the aromatic curing agent 4,4'-diaminodiphenylsulfone (DDS). As shown for this system in a former study by Oyama et al. [Oyama HT, Lesko JJ, Wightman JP. J Polym Sci B 1997;35:33146. [36]], preferential absorption of amine molecules by PVP can occur. In the present study, the focus is on the variations of local elastic properties within the epoxy interphase adjacent to the PVP layer. The curing was performed close to the glass transition temperature, Tα, of the PVP film, namely at 170 °C. Variations of the local amine concentration were tracked using energy-dispersive analysis of X-rays (EDX), by taking benefit of the sulfur contained in DDS. Using temperature-dependent dynamic mechanical analysis (DMA), a series of epoxy reference samples of different amineepoxy concentration ratios, r, was investigated in order to work out the relationship between r and the epoxy storage modulus at room temperature. In the excess-epoxy regime, r<1, the modulus is observed to increase with departure from the stoichiometric ratio, r=1. Considering the respective suppression of the ß-transition, the observed characteristic can be explained by an antiplasticisation effect. Depth-sensing indentation (DSI) experiments across the epoxy/PVP interphase provided evidence for strong modulus variations. In consistency with the EDX and the DMA data, in the vicinity of the PVP layer the local epoxy modulus is increased. The total change of the epoxy Young's modulus is ~1.1 GPa. However, the total width of the modulus decay of ~175 µm is ~2.5 times larger than the one of the DDS concentration gradient. This finding is discussed in terms of additional spatial variations of the DGEBA concentration as well as long-range diffusion currents of DDS induced by the interdiffusion processes and their effect on the final network of crosslinks.
A report is presented on the development of a test for determining the long-term oxidation resistance of polyolefin materials, which is accelerated not only by elevated temperatures but also by increased oxygen pressure and a stirred aqueous medium. The method permits durability tests to be carried out at markedly lower temperatures with reasonable testing durations and significantly reduced diffusion limited oxidation effects and allows for physical and chemical impacts of aqueous media. Oxidative durability can be assessed by autoclave immersion exposures at three different temperatures (60, 70 and 80 degrees C) and 50 bar oxygen pressure and at 80 degrees C and two different oxygen pressures (usually 10 and 20 bar). Accelerated test data are evaluated by modified Arrhenius equations with the application of a three-dimensional regression analysis. The application of the test method to various materials, including PP non-woven materials and geosynthetics is demonstrated. 10 refs.
Applying a high-frequency lateral vibration between tip and sample in a scanning force microscope (SFM), a harmonically modulated lateral (friction) force image can be obtained using lock-in techniques. Harmonically modulated lateral force microscopy (HM-LFM) offers several advantages compared with standard lateral force microscopy (LFM). After a brief investigation of the scan velocity dependence of LFM and HM-LFM, two samples were investigated. First, the surface of a poly(acrylonitrile-co-styrene)/polybutadiene blend (ABS) was used to demonstrate the ability of the new technique to decrease the stick effects of the SFM tip. Second, an interface between two chemically very similar polymers was prepared by melting polypropylene (PP) and poly(propene-block-ethene) (PP-block-PE) films on each other. After cutting, the surface roughness of this sample was very high. It is shown that only HM-LFM clearly resolves the local micromechanical properties without artefacts.