Filtern
Dokumenttyp
Referierte Publikation
- ja (7) (entfernen)
Schlagworte
- Ultrasound (7) (entfernen)
Organisationseinheit der BAM
Ultrasound sensors should be embedded into concrete for monitoring concrete properties. These new longitudinal wave sensors with a center frequency of 60 kHz were examined regarding their suitability for ultrasonic measurements in concrete structures in terms of emission characteristics, sensitivity and frequency ränge.
For the measurement of the radiation patterns, the sensors were embedded vertically and horizontally in concrete cylinders. The directivity pattern was measured using a laser vibrometer.
The sensitivity of the sensor was determined in water using different sensors of the same type. It shows changes in the signal amplitude as well as variations in the frequency ränge for different transmitter-receiver combinations.
The attenuation of the concrete affects the achievable resolution of the measurements and thus, the maximum possible spacing of the sensors within a concrete element. Experimental tests helped optimizing the distances with respect to the required resolution and the effort of embedding the sensors. The signal attenuation in the concrete was measured in the frequency ränge of 60 kHz in response to various degrees of reinforcement and grain size. For this purpose, the sensors were cast at different distances in the specimens studied. The recorded Signals were evaluated for their amplitude and frequency spectrum.
Integration of fiber reinforcement in high-performance cementitious materials has become widely applied in many fields of construction. One of the most investigated advantages of steel Fiber reinforced concrete (SFRC) is the deceleration of crack growth and hence its improved sustainability.
Additional benefits are associated with its structural properties, as fibers can significantly increase the ductility and the tensile strength of concrete. In some applications it is even possible to entirely replace the conventional reinforcement, leading to significant logistical and environmental benefits.
Fiber reinforcement can, however, have critical disadvantages and even hinder the Performance of concrete, since it can induce an anisotropic material behavior of the mixture if the fibers are not appropriately oriented. For a safe use of SFRC in the future, reliable non-destructive testing (NDT) methods need to be identified to assess the fibers’ orientation in hardened concrete. In this study,
ultrasonic material testing, electrical impedance testing, and X-ray computed tomography have been investigated for this purpose using specially produced samples with biased or random Fiber orientations. We demonstrate the capabilities of each of these NDT techniques for fiber orientation measurements and draw conclusions based on these results about the most promising areas for future research and development.
Dieser Beitrag stellt die aktuellen Fortschritte der Ultraschallprüfung von Betonbauteilen basierend auf dem ICA-Verfahren vor. Das eingesetzte Verfahren wird bereits erfolgreich in anderen Bereichen der Ultraschallprüfung angewendet. Das große Potential dieser Methode liegt in der Möglichkeit, die sich überlagernden Reflexionen der Ultraschallsignale durch nur wenige Messungen in Echtzeit voneinander zu trennen und durch einfache Triangulation zu lokalisieren.
Es wurden Experimente hinsichtlich der Eignung und praktischer Relevanz des JADE-Algorithmus durchgeführt. Die Untersuchungen erfolgten sowohl an Polyamid als auch an Betontestkörpern. Die Leistungsfähigkeit des JADE-Algorithmus bezüglich der Quellsignaltrennung wird anhand von mehrkanaligen Ultraschallmessungen gezeigt. Die extrahierten Komponenten enthalten Signalanteile, die mit den entsprechenden Echosignalen in der Messung korrelieren.
Zukünftig wird das untersuchte Verfahren mit der Gruppenstrahlertechnik und einem geeigneten Sende-Empfangskonzept kombiniert, um so die Aussagesicherheit der zerstörungsfreien Untersuchungen zu erhöhen.
Muon Tomography of the Interior of a Reinforced Concrete Block: First Experimental Proof of Concept
(2021)
Quality assurance and condition assessment of concrete structures is an important topic world-wide due to the aging infrastructure and increasing traffic demands. Common topics include, but are not limited to, localisation of rebar or tendon ducts, geometrical irregularities, cracks, voids, honeycombing or other flaws. Non-destructive techniques such as ultrasound or radar have found regular, successful practical application but sometimes suffer from limited resolution and accuracy, imaging artefacts or restrictions in detecting certain features. Until the 1980s X-ray transmission was used in case of special demands and showed a much better resolution than other NDT techniques. However, due to safety concerns and cost issues, this method is almost never used anymore. Muon tomography has received much attention recently. Novel detectors for cosmic muons and tomographic imaging algorithms have opened up new fields of application, such as the investigation of freight containers. Muon imaging also has the potential to fill some of the gaps currently existing in concrete NDT. As a first step towards practical use and as a proof of concept we used an existing system to image the interior of a reference reinforced 600 kg concrete block. Even with a yet not optimized setup for this kind of investigation, the muon imaging results are at least of similar quality compared to ultrasonic and radar imaging, potentially even better. The data acquisition takes more time and signals contain more noise, but the images allowed to detect the same important features that are visible in conventional high energy X-ray tomography. In our experiment, we have shown that muon imaging has potential for concrete inspection. The next steps include the development of mobile detectors and optimising acquisition and imaging parameters.
Validation of novel ultrasonic phased array borehole probe by using simulation and measurement
(2022)
Low-frequency ultrasonic testing is a well-established non-destructive testing (NDT) method in civil engineering for material characterization and the localization of cracks, reinforcing bars and delamination. A novel ultrasonic borehole probe is developed for in situ quality assurance of sealing structures in radioactive waste repositories using existing research boreholes. The aim is to examine the sealing structures made of salt concrete for any possible cracks and delamination and to localize built-in components. A prototype has been developed using 12 individual horizontal dry point contact (DPC) shear wave transducers separated by equidistant transmitter/receiver arrays. The probe is equipped with a commercially available portable ultrasonic flaw detector used in the NDT civil engineering industry. To increase the sound pressure generated, the number of transducers in the novel probe is increased to 32 transducers. In addition, the timed excitation of each transducer directs a focused beam of sound to a specific angle and distance based on the previously calculated delay time. This narrows the sensitivity of test volume and improves the signal-to-noise ratio of the received signals. In this paper, the newly designed phased array borehole probe is validated by beam computation in the CIVA software and experimental investigations on a half-cylindrical test specimen to investigate the directional characteristics. In combination with geophysical reconstruction methods, it is expected that an optimised radiation pattern of the probe will improve the signal quality and thus increase the reliability of the imaging results. This is an important consideration for the construction of safe sealing structures for the safe disposal of radioactive or toxic waste.
Die immer komplexere Konstruktionsweise von Neubauten einerseits und die alternde Infrastruktur andererseits erfordern in manchen Fällen eine dauerhafte Überwachung, um besondere Einwirkungen und gegebenenfalls Schädigungen rechtzeitig und genau zu erkennen. Hierfür ist eine Vielzahl von Methoden und Sensoren verfügbar. Das Portfolio weist aber insbesondere bei der Detektion langsamer, räumlich begrenzter Veränderungen Lücken auf. Hierfür sind bisher sehr aufwändige Untersuchungen oder Installationen notwendig.
In der vorliegenden Arbeit werden Sensoren und zugehörige Auswertemethoden für die Ultraschalltransmission vorgestellt, die sich für die zerstörungsfreie, dauerhafte Überwachung von Beton eignen. Direkt oder nachträglich in Betonkonstruktionen eingebaut, ermöglichen sie eine nicht nur lokale, sondern größere Raumbereiche umfassende Dauerüberwachung von Änderungen der Materialeigenschaften.
Das Prinzip der Ultraschalltransmission und die verschiedenen Einflussparameter werden vorgestellt. Zu letzteren gehören neben der Belastung und Schädigung auch Umweltparameter wie Temperatur und Feuchte. Verschiedene Methoden zur Datenanalyse, wie z. B. die Codawelleninterferometrie, ermöglichen eine Detektion kleinster Veränderungen. Die in den Beton einzubettenden Ultraschallsensoren werden vorgestellt und ihr Einbau und Betrieb beschrieben. Als Beispiele für Anwendungen werden Frost-Tauwechsel-Experimente im Labor, die Detektion von lokalen Lasten im Technikumsmaßstab und der Einsatz an realen Brücken diskutiert. Die Sensoren sind zum Teil bereits seit mehreren Jahren in Probeobjekte eingebettet und liefern zuverlässig wertvolle Daten.-------------------------------------------------------------------------------------------------------------------------------------------------------------
Monitoring of concrete constructions by embedded ultrasonic sensors:
Challenging new constructions and the ageing infrastructure are increasing the demand for permanent monitoring of loads and damages. Various methods and sensors are used for this purpose. But the technologies available today have difficulties in detecting slowly progressing locally confined damages. Extensive investigations or instrumentations are required so far for this purpose.
In this study we present new sensors and data processing methods for ultrasonic transmission, which can be used for non-destructive permanent monitoring of concrete. They can be mounted during construction or thereafter. Larger volumes can be monitored by a limited number of sensors for changes of material properties.
The principles of ultrasonic transmission and influencing factors are presented. This latter include load, damages as well as environmental parameters as temperature or moisture. Various methods for data processing, e. g. coda wave interferometry are introduced. They allow the detection of very small changes in the medium. The embedded sensors are shown including mounting and operation. Application examples so far include small scale laboratory freeze-thaw experiments, localizing loads in larger concrete models and monitoring load effects on real structures. Some sensors are operating already for several years.
Recently developed new transducers for ultrasonic transmission, which can be embedded right into concrete, are now used for non-destructive permanent monitoring of concrete. They can be installed during construction or thereafter. Large volumes of concrete can be monitored for changes of material properties by a limited number of transducers. The transducer design, the main properties as well as installation procedures are presented. It is shown that compressional waves with a central frequency of 62 kHz are mainly generated around the transducer's axis. The transducer can be used as a transmitter or receiver. Application examples demonstrate that the transducers can be used to monitor concrete conditions parameters (stress, temperature,
) as well as damages in an early state or the detection of acoustic events (e.g., crack opening). Besides application in civil engineering our setups can also be used for model studies in geosciences.