Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (43)
Sprache
- Englisch (43) (entfernen)
Referierte Publikation
- nein (43)
Schlagworte
- Degradation (7)
- Acceptance rate (6)
- Composite (5)
- Sample performance chart (5)
- Basic population (3)
- Catastrophe (3)
- End of life (3)
- Minimum burst ratio (3)
- Regulations (3)
- Scatter (3)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (43) (entfernen)
Implementation and current situation of introducing the Directives 97/23/EC in the German legislaton
(2001)
The presentation reflects the questions that have been raised by member states and NGOs.
As background information details on the question how to choose a suitable salvage pressure receptacle (SPR) are provided. This leads to the need for deleting the volume limitation for SPRs and to the discussions in 2014 and 2016 on this issue.
As an adequate substitution for deleting the volume limit for SPRs it is proposed to limit the pressure receptacles to be stored in by a maximum pressure-volume-value of 1.5 Mio bar-litres.
After some explanations to standardisation projects currently also tackling this pV-limit, some risk-based safety criteria for a limitation are mentioned with the focus of the consequence level and the general avoidance of catastrophic worst case scenarios.
First the acceptance rates resulting from the analysis of different minimum burst ratios and standards are displayed and explained. Especially the problems resulting from a further reduction if the minimum burst ratio are shown.
For a better understanding of these results the process of analysing the acceptance rate is explained in detail. This contains the alleged contradiction between safety of samples due to its scatter while the rejected sample provides a higher mean strength.
Then the importance of batch testing is explained and leads to the recommendation to have a strong interaction between provided mean strength and requested maximum of production scatter.
Based on the preliminary presentations in this task force it is repeated how a basic population scatters and its degradation influences properties statistically. There is a remainder on the issue of accepting borderline populations due to the minimum burst ratio requirement.
Then it is explained in detail how the analysis of minimum requirements by a Monte-Carlo-simulation works. The result with respect to the further reduced minimum burst ratio of 2.0 is summarised and means a two-step approach of two scatter levels requiring two different minimum burst ratios.
The methods for evaluating batch tests are analysed. A proposal for integration a statistical analysis is described in detail.
Finally, the positive effect of proof testing is shown and its dependence from the real ageing is shown.
This ends in the recommendation to have a stronger and quantitative look on real ageing and to follow the 2 proposed sets of criteria for a safe usage of hydrogen storage systems.
The reduced volume method has found a particular zone to be used for evaluating the strength of unidirectional composite materials. To validate the method, modelling an experimental test where it has the same basic assumption of the model had been carried out. The result was favourable as the model can predict the average value from the experiment and also the time dependent effect.
This presentation explains how an PA-based approval concept could work and would substitute the most of deterministic requirements based on a risk based quantification of accepted failure rates.
The concept of a probabilistic approval approach is based on 5 separate types of requirements:
1. Testing and evaluation of properties at Beginning of Life (BoL)
2. Artificial aging with residual strength assessment
3. Testing against dedicated accidental loads
4. Surveillance of production quality
5. Surveillance of degradation/ check of estimated end of life (EoL)
Each of these aspects is visualised by photos and diagrams.
This presentation provides an impression of the boundary condition of the work on composite cylinders on a competent authority. It shows the various kinds of usage, the different tasks and duties around this kind of storage units and the wide spread of technical competence necessary for the substantial research when addressing the legislation. Based on this it shows how we react on changes in the regulations by research and how this influences the regulations, again. As an example, our probabilistic approach is mentioned and drafted for getting mentioned several times during the ongoing set of presentations.
Conventional approval requirements exclusively ask for minimum strength values, which have to be met. The probabilistic approach estimates how likely none of the comparatively manufactured units fails during operation.
Both questions are juxtaposed and compared here with respect to the load cycle tests. The influence of the sample sizes is discussed additionally.
The introduction reflects the political background in Germany and worldwide concerning hydrogen as energy carrier. This leads to available hydrogen strategies and the reaction of BAM by launching the competence centre H2Safety@BAM. Fokus is set on the competence area TestCert, the special role of the division “Safety of Gas Storage Systems” there and its increasing success in research activities.
The main part explains the needs for a risk-controlled market ramp-up concerning hydrogen products and appropriate measures being under development in division 3.5: risk control, tools for consequence estimation and limitation, probabilistic assessment of end of safe life, the efficiency assessment and optimization of current regulations, the structural health monitoring (SHM) with necessary improvement of measures for quality management in the digital world of safety assessment. Last but not least, the wide range of full-scale testing and simulation of worst-case scenarios is explained.