Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (34)
- Beitrag zu einem Tagungsband (26)
- Zeitschriftenartikel (16)
- Posterpräsentation (3)
- Beitrag zu einem Sammelband (2)
- Monografie (1)
Sprache
- Englisch (82) (entfernen)
Schlagworte
- Degradation (11)
- Regulations (8)
- Slow burst test (8)
- Acceptance rate (7)
- Composite (7)
- Residual strength (7)
- Composite cylinders (6)
- End of life (6)
- Hydrogen (6)
- Safety (6)
Organisationseinheit der BAM
- 3 Gefahrgutumschließungen; Energiespeicher (28)
- 3.0 Abteilungsleitung und andere (17)
- 3.5 Sicherheit von Gasspeichern (11)
- 5 Werkstofftechnik (3)
- 5.5 Materialmodellierung (3)
- 8 Zerstörungsfreie Prüfung (2)
- 8.6 Faseroptische Sensorik (2)
- 2 Prozess- und Anlagensicherheit (1)
- 2.1 Sicherheit von Energieträgern (1)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (1)
Eingeladener Vortrag
- nein (34)
Applications by fire brigades expose the composite cylinders to harsh temperature and handling conditions. Standards have been used for certifying composite cylinders, which are designed for transport of dangerous goods and do not reflect service conditions specific to fire brigades. In this paper, the residual safety of a design type (fully wrapped with aluminum and carbon fiber composite) at the end of their service life of 15 yrs is analyzed. One sample underwent hydraulic load cycle (LC) tests, another conventional burst tests, and the third slow burst tests (SBTs). The statistical evaluation and the handling of an unexpected high amount of early failures are shown.
Hydrogen is an attractive energy carrier that requires high effort for safe storage. For ensuring safety they have to undergo a challenging approval process. Relevant standards and regulations for composite cylinders used for the transport of for on-board storage of hydrogen are currently based on deterministic (e.g. ISO 11119-3) or semi-probabilistic (UN GTR No. 13) criteria. This paper analysis the properties of such methods in regards to the evaluation of load cycle strength. Their characteristics are compared with the probabilistic approach of the BAM. Based on Monte-Carlo simulations, the available design range (mean value and scatter of strength criteria) of current concepts were exemplarily estimated. The aspect of small sample sizes is analysed and discussed with respect to the evaluation procedures.
The developed model has certain limitations of the element size to be used in the simulation to characterise the strength of composite materials. A reduced volume method is proposed in order to reduce the number of degree of freedom of the finite element simulation.This study has revealed certain configuration to be followed to speed up the computation time.
Safety criteria for the transport of hydrogen in permanently mounted composite pressure vessels
(2020)
The recent growth of the net of hydrogen fuelling stations increases the demands to transport compressed hydrogen on road by battery vehicles or tube-trailers, both in composite pressure vessels. As a transport regulation, the ADR is applicable in Europe and adjoined regions, and is used for national transport in the EU. This regulation provides requirements based on the behaviour of each individual pressure vessel, regardless of the pressure of the transported hydrogen and relevant consequences resulting from generally possible worst case scenarios such as sudden rupture. In 2012, the BAM (German Federal Institute for Materials Research and Testing) introduced consequence-dependent requirements and established them in national transport requirements concerning the “UN service life checks” etc. to consider the transported volume and pressure of gases. This results in a requirement that becomes more restrictive as the product of pressure and volume increases. In the studies presented here, the safety measures for hydrogen road transport are identified and reviewed through a number of safety measures from countries including Japan, the USA and China. Subsequently, the failure consequences of using trailer vehicles, the related risk and the chance are evaluated. A benefit-related risk criterion is suggested to add to regulations and to be defined as a safety goal in standards for hydrogen transport vehicles and for mounted pressure vessels. Finally, an idea is given for generating probabilistic safety data and for highly efficient evaluation without a significant increase of effort.
We present the results of distributed fiber optic strain sensing for condition monitoring of a hybrid type IV composite fully wrapped pressure vessel using multilayer integrated optical fibers. Distributed strain sensing was performed for a total number of 252,000 load cycles until burst of the vessel. During this ageing test material fatigue could be monitored and spatially localized. Critical material changes were detected 17,000 cycles before material failure. Results have been validated by acoustic emission analysis.
The introduction reflects the political background in Germany and worldwide concerning hydrogen as energy carrier. This leads to available hydrogen strategies and the reaction of BAM by launching the competence centre H2Safety@BAM. Fokus is set on the competence area TestCert, the special role of the division “Safety of Gas Storage Systems” there and its increasing success in research activities.
The main part explains the needs for a risk-controlled market ramp-up concerning hydrogen products and appropriate measures being under development in division 3.5: risk control, tools for consequence estimation and limitation, probabilistic assessment of end of safe life, the efficiency assessment and optimization of current regulations, the structural health monitoring (SHM) with necessary improvement of measures for quality management in the digital world of safety assessment. Last but not least, the wide range of full-scale testing and simulation of worst-case scenarios is explained.
Composite materials show a degradation of properties depending on service life. This creates the necessity to find tailored methods to determine strength and residual strength of composite cylinders. The determination can be done e.g. by load cycles tests. The result needs a statistical assessment for the precise description of strength. Especially the statistical assessment of load cycle strength properties has a high uncertainty. It is unclear if a Log-Normal distribution, a WEIBULL distribution or others, describe the scatter behaviour of residual strength properties correctly.
Distribution functions aim at approximating the frequency of occurrence of residual load cycle strength for high survival rates. An assumption has to be found and confirmed to prevent over-estimation of reliability.
Fibre-reinforced plastics (FRP) especially carbon-fibre-reinforced polymer (CFRP) and glass-fibre-reinforced polymer (GFRP) are commonly used materials in high pressure vessels and storage units for automotive and aerospace purposes. Optical fibres are suitable to be integrated or directly applied to the surface of FRP components. Using optical fibres it is possible to monitor the distributed strain profiles and changes within the fatigue life of a pressure vessel to ensure the operational safety. Within artificial ageing experiments we used swept wavelength interferometry (SWI) based distributed strain sensing for the monitoring of commercial high-pressure composite cylinder. This artificial ageing was performed using test conditions of 503bar pressure load (service pressure 300 bar) and 89 °C for 100 h. The polyimide coated optical fibres were glued to the surface externally in circumferential and axial direction. Using distributed strain sensing (DSS) material expansion of over 0.5% were monitored with sub-centimetre spatial resolution. Within the circumferential direction we observed up to 10 % local fluctuation compared to the median strain caused by inhomogeneous material expansion, which could cause local material fatigue. In addition, we determined material degradation manifested itself as localized remaining material expansion and/or contraction. Results have been validated by other non-destructive methods like digital strip projection.
Developers interested in high pressure storage of hydrogen for mobile use increasingly rely on composite cylinders for onboard storage or transport of dangerous goods. Thus, composite materials and systems deserve special consideration. History gives interesting background information important to the understanding of the current situation as to regulations, codes and standards.
Based on this review, origins of different regulations for the storage of hydrogen as dangerous good and as propellant for vehicles will be examined. Both categories started out using steel and sometimes aluminium as cylinder material. With composite materials becoming more common, a new problem emerged: vital input for regulations on composite pressure systems was initially derived from decades of experience with steel cylinders. As a result, both regulatory fields suffer somewhat from this common basis. Only recent developments regarding requirements for composite cylinders have begun to go more and more separate ways. Thus these differences lead to some shortcomings in regulation with respect to composite storage systems.
In principle, in spite of separate development, these deficits are in both applications very much the same: there are uncertainties in the prediction of safe service life, in retesting procedures of composite cylinders and in their intervals. Hence, different aspects of uncertainties and relevant approaches to solutions will be explained.