Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (9)
- Beitrag zu einem Tagungsband (7)
- Beitrag zu einem Sammelband (4)
- Vortrag (3)
- Buchkapitel (1)
Schlagworte
- Thermography (24) (entfernen)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (11)
- 8.0 Abteilungsleitung und andere (10)
- 9 Komponentensicherheit (4)
- 9.3 Schweißtechnische Fertigungsverfahren (4)
- 1 Analytische Chemie; Referenzmaterialien (1)
- 1.9 Chemische und optische Sensorik (1)
- 6 Materialchemie (1)
- 6.3 Strukturanalytik (1)
- 8.5 Röntgenbildgebung (1)
Eingeladener Vortrag
- nein (3)
False colour infrared (IR) thermography was performed on a sunny summer day in the Berlin Botanic Garden. The main interest focused on blossoms of different size, colours and shapes: disk-, bowl- and funnel-like anatomy demonstrating various modes of light absorption and heating-up during the day. Some of the flowers were phototropic or even solar tracking. Blossom temperatures ranged from 18.0 to 33.3 °C (mean 26.3 ± 2.5 °C, S.D., n = 37) at 21 °C air temperature. Several thermograms showed honey- and bumblebees also. In some cases the results are compared with those of a contact-free IR thermometry. One winter- and one late-spring-flowering plant are included in the overview.
Heat transfer modeling of local thermal excitation for surface crack detection and characterization
(2010)
In the presented paper the use of local excitation (laser beam) for crack detection and
characterization is simulated. As we could see, using the temperature differences between two
reference points was large enough to detect and characterize the crack, even for such small value of
laser power as 2 W. The influence of radiation and convection on the temperature difference was
negligible (about 0.1%). The influence of heat conduction, in case of crack with air, was very small
(about 3%). The main mechanism which influences the temperature differences between the
reference points is the heat conduction in steel. From the presented results one can see that
temperature differences are increasing with an increase of the crack depth or the crack length. Better
resolution and characterization of the crack depths and lengths should be achieved with increased
duration of heating time or the laser power. We could also see that the best position for the laser
spot to characterize the crack is the closest one. Also, comparison of 2D and 3D simulation results
for circular heat source used as local excitation mechanism had showed that only full 3D modelling
will allow accomplishing a quantitative level of comparison between experimental and simulation
results.
We report on recent developments in the detection of surface breaking cracks using
flying laser spot thermography. Application of an infrared camera for mapping the
thermal radiation after excitation with a diode laser equipped with an optical scanner
allows us to examine a surface containing cracks in an entirely non-destructive,
contactless and fast way, without even moving the camera. We developed an efficient
and robust algorithm that can be applied directly to the recorded thermal sequences,
and that derives a single image containing all crack signatures. For this crack detection
technique, no specific synchronisation between laser and camera is required. Hence,
our approach is suitable for an upgrade of existing thermographic systems. The
feasibility of the proposed procedure is proven by testing an artificial test sample and a
piece of rail that comprises roll contact fatigue cracks and by comparing the results
with magnetic particle testing.
Active thermography is a nowadays widely used NDT method making use of thermal material properties for defect detection. Basically, the sample is heated and the resulting surface temperature is recorded by an IR camera. For laser thermography a laser is used to heat the sample locally. The resulting spherical heat flow allows the detection of voids in arbitrary orientation. In this work, a method is presented which is suitable for the quantitative characterization of depth and angle of surface cracks. The main idea is to evaluate the crack-caused asymmetries of the laser's thermal footprint. The heat is introduced at fixed reference positions relative to the crack. In this paper a data analysis procedure is presented which allows the crack depth and angle to be described by only two characteristic scalar parameters. By investigating artificial test specimens with spark eroded notches, the feasibility of this method is validated. Furthermore, the behavior of the characteristic parameters with variations of crack angle, depth and experimental conditions is studied systematically by FEM simulations, showing that these parameters are well behaved.
Spot welding is one of the most important technologies for joining sheet metal. While there are lot of approaches to non-destructive testing, quality assurance still mainly relies on welding parameter monitoring and destructive testing, leading to significant failure rates. In this paper an approach to spot weld testing using flash thermography is presented. The main focus of attention is on the identification of two typical error classes: stick welds and welds at the splash limit. Besides investigating the principal feasibility of thermography for zinc plated samples the results of a series test of spot welds joining 1 mm thick TRIP steel are shown. Based upon these results a statistical criterion is developed which allows a reliable classification of the named error classes.
We present a systematic study on the performance of laser-thermography for the detection of surface cracks in metallic components. Scanning a metallic surface with laser causes local heating that is mapped simultaneously by an IR-camera and allows identifying cracks with sub-µm openings. The detectability, however, depends on a number of acquisition parameters (e.g. scanning speed, laser power, IR-camera resolution) that typically relate on each other. Most importantly, the detection-sensitivity of surface breaking cracks is given by a particular combination for the acquisition parameter values. As a result, this sensitivity is adaptable within wide ranges allowing the detection of cracks with openings ranging from 200 to 0.1 µm at testing speeds of 100 to 0.05 cm²/s. By examining artificial as well as fatigue cracks, we demonstrate that the method can be even applied to shiny surfaces with no need of pretreatments, which makes it an entirely contactless, remote and automatable NDT technique. A comparison with magnetic particle testing shows that laser-thermography has the potential to become a strong competitor to conventional surface inspection methods in the future.
Monitoring of cracks in historic concrete structures using optical, thermal and acoustical methods
(2015)
Cracks are a major issue in the field of cultural heritage. In order to evaluate the significance of a crack, a long term monitoring of the damaged region is required. However, there is a lack of easy to operate tools for such monitoring measures. Therefore, new or existing methods for other applications have to be optimised for cultural heritage investigation. The paper describes the application of such crack observation methods on a historic concrete sculpture. Beside conventional methods, like mapping by hand and ultrasonic depth profiling, a novel tracking system is presented. Furthermore, the suitability of active thermography for the investigation of cracks was investigated. The results show promising prospects for these non-destructive techniques.
We present a first direct measurement of the temperature during milling combined with in situ Raman spectroscopy monitoring. The data reveal a low temperature increase due to the mechanical impact and clear temperature increases as a consequence of the reaction heat. Based on the data, temperature rises as postulated in the magma plasma and hot spot theory can be excluded for soft matter milling syntheses.
Additive manufacturing (AM) offers a range of novel applications. However, the manufacturing process is complex and the production of defect-free parts with high reliability and durability is still a challenge. Thermography is a valuable tool for process surveillance, especially in metal AM processes. The high process temperatures allow one to use cameras usually operating in the visible spectral range. Here, we compare the results of measurements during the manufacturing process of a commercial laser metal deposition setup using a mid-wavelength-IR camera with those from a visual spectrum high-speed camera with band pass filter in the near-IR range.
Quantification of impact damages in CFRP and GFRP structures with thermography and ultrasonics
(2018)
For the quantification of impact damage in CFRP and GFRP structures, first passive thermography measurements have been performed at the front and rear side of the test specimens during low velocity impact load. After loading, the damaged structures have been investigated non-destructively with active thermography with flash excitation and with step heating and with two different ultrasonic methods (phased array and air coupled ultrasonics). The damage sizes quantified with all methods are evaluated and compared. In addition, the depth of the greatest damage inside the different test specimens is analysed.
We present an in situ triple coupling of synchrotron X-ray diffraction with Raman spectroscopy, and thermography to study milling reactions in real time. This combination of methods allows a correlation of the structural evolution with temperature information. The temperature information is crucial for understanding both the thermodynamics and reaction kinetics. The reaction mechanisms of three prototypical mechanochemical syntheses, a cocrystal formation, a C@C bond formation (Knoevenagel condensation), and the formation
of a manganese-phosphonate, were elucidated. Trends in the temperature development during milling are identified. The heat of reaction and latent heat of crystallization of the product contribute to the overall temperature increase. A decrease in temperature occurs via release of, for example, water as a byproduct.
Solid and liquid intermediates are detected. The influence of the mechanical impact could be separated from temperature effects caused by the reaction.
Impact damages and delaminations in fibre-reinforced composites (FRC) might not be visible at the surface, but could have an influence on the resistance and on the long-term behaviour of the component. Therefore, and especially for safety relevant structures, non-destructive methods are required for the assessment of such damages.
Active thermography methods are suitable to characterize damages after loading using different kind of excitation techniques and various configurations of infrared (IR) camera and heating sources. Here, flash lamps, impulse excitation with infrared radiator and lock-in technique with halogen lamps or widened laser beams are suited. In addition, non-optical sources like sonotrodes (requiring direct contact to the structure) or induction generators (only suited for carbon fibre reinforced polymer (CFRP) structures) could be applied as well. For the investigation of the evolution of the damage during the impact, passive thermography can be applied in-situ. Elastic and plastic deformations alter the temperature of the structure and thus the temperature on the surface.
In this contribution, at first the general principles of quantitative defect characterisation in FRC using active thermography with flash, impulse and lock-in excitation are described. Optical and thermal properties of the FRC material and its anisotropy are considered. Results of phase differences obtained at flat bottom holes with flash and lock-in thermography are compared for qualifying both methods for quantitative defect characterization. Secondly, the damage evolution of CFRP and GFRP structures under impact load and static tensile loading is described. The spatial and temporal evolution of the surface temperature enables us to distinguish matrix cracks or fibre-matrix separation from delaminations between the layers. Afterwards, all results for loading defects, obtained by passive and active thermography, are compared with each other. Fig. 1 and 2 show the difference of passive and flash thermography obtained at impact and tensile loaded CFRP plates, respectively. As one purpose of these investigations is the development of standards within national (DIN) and European (CEN) standardisation bodies, new draft and final standards are presented and further needs are discussed at the end of the presentation.
In this paper shortwave infrared (SWIR) thermographic measurements of the manufacturing of thin single-line walls via laser metal deposition (LMD) are presented. As the thermographic camera is mounted fixed to the welding arm, an acceleration sensor was used to assist in reconstructing the spatial position from the predefined welding path. Hereby we could obtain data sets containing the size of the molten pool and the oxide covered areas as functions of the position in the workpiece. Furthermore, the influence of the acquisition wavelength onto the thermograms was investigated in a spectral range from 1250 nm to 1550 nm. All wavelengths turned out to be usable for the in-situ process monitoring of the LMD process. The longer wavelengths are shown to be beneficial for the lower temperature range, while shorter wavelengths show more details within the molten pool.
Additive manufacturing offers a range of novel applications. However, the manufacturing process is complex and the production of almost defect-free parts with high reliability and durability is still a challenge. Thermography is a valuable tool for process surveillance, especially in metal additive manufacturing processes. The high process temperatures allow one to use cameras usually operating in the visible spectral range. Here, we compare the results of measurements during the manufacturing process of a commercial laser metal deposition setup using a mid wavelength infrared camera with those from a short wavelength infrared camera and those from a visual spectrum high-speed camera with band pass filter in the near infrared range.
Thermography is one on the most promising techniques for in-situ monitoring of metal additive manufacturing processes. Especially in laser powder bed fusion processes, the high process dynamics and the strong focus of the laser beam cause a very complex thermal history within the produced specimens, such as multiple heating cycles within single layer expositions. This complicates data interpretation, e.g., in terms of cooling rates. A quantity that is easily calculated is the time a specific area of the specimen is at a temperature above a chosen threshold value (TOT). Here, we discuss variations occurring in time-over-threshold-maps during manufacturing of an almost defect free cuboid specimen.