Filtern
Dokumenttyp
- Zeitschriftenartikel (3)
- Vortrag (1)
Sprache
- Englisch (4)
Schlagworte
- Flash thermography (4) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Flash lamps are widely used excitation sources in the field of non-destructive testing with active thermography. Though the realized energy density in front of the investigated object is a significant factor with regard to detection sensitivity, only few data concerning this issue have been published so far. It is shown here that local energy densities can be estimated by means of a simple metal plate, which exhibits a certain temperature increase after flash excitation. After discussing the underlying calorimetric principle the sensor concept is reviewed using constant blackbody radiation and short laser pulses, since both kinds of sources generate known energy densities. The relative uncertainty of measurements of the energy density is found to be in the range of 10%. The last part of the present paper describes an application for characterizing the radiation of a usual 6 kJ flash lamp. The energy conversion efficiency was found to be only about 11%.
Comparison of concepts for a point-shaped energy density detector after flash lamp excitation
(2016)
The paper describes investigations and Research work in order to develop a simple sensor for the quantification of spectral broadband energy Dissipation of flash lamps at any point in space. Such Flash lamps are often used as energy source during active thermography testing (TT). Here, the temperature transient of the sensor surface has to be recorded by the infrared camera that is already present. During the following data evaluation, the energy input into the investigated specimen can be determined. Two opposite concepts were considered: thermal thick and thermal thin probes. The direct comparison shows advantages for thermal thick probes based on the physics of thermal balance processes.
Cooling-down of thermal thick probes after flash excitation - A measure for the real energy density?
(2015)
Though flash lamps are one of the most applied heat sources in the field of Thermographic Testing (TT) using active thermography, only little is known about the actually achieved energy input into test objects. In this paper, an easy to realize sensor concept is proposed and experimentally evaluated. The concept is based on the measurement of the surface temperature of a thermal thick probe after flash excitation. After considering the sensor concept with FEM simulations the experimental investigation of four materials (two polymer and two building materials) is described. It will be shown that a suited coating is essential for the realization of the sensor concept. The experimental results prove the suitability of black rigid PVC as the most promising material. Using a coated PVC sample the energy density of short laser pulses, similar to flashes of flash lamps, could be determined exactly with an estimated relative uncertainty of only a few percent.
Impact damages and delaminations in fibre-reinforced composites (FRC) might not be visible at the surface, but could have an influence on the resistance and on the long-term behaviour of the component. Therefore, and especially for safety relevant structures, non-destructive methods are required for the assessment of such damages.
Active thermography methods are suitable to characterize damages after loading using different kind of excitation techniques and various configurations of infrared (IR) camera and heating sources. Here, flash lamps, impulse excitation with infrared radiator and lock-in technique with halogen lamps or widened laser beams are suited. In addition, non-optical sources like sonotrodes (requiring direct contact to the structure) or induction generators (only suited for carbon fibre reinforced polymer (CFRP) structures) could be applied as well. For the investigation of the evolution of the damage during the impact, passive thermography can be applied in-situ. Elastic and plastic deformations alter the temperature of the structure and thus the temperature on the surface.
In this contribution, at first the general principles of quantitative defect characterisation in FRC using active thermography with flash, impulse and lock-in excitation are described. Optical and thermal properties of the FRC material and its anisotropy are considered. Results of phase differences obtained at flat bottom holes with flash and lock-in thermography are compared for qualifying both methods for quantitative defect characterization. Secondly, the damage evolution of CFRP and GFRP structures under impact load and static tensile loading is described. The spatial and temporal evolution of the surface temperature enables us to distinguish matrix cracks or fibre-matrix separation from delaminations between the layers. Afterwards, all results for loading defects, obtained by passive and active thermography, are compared with each other. Fig. 1 and 2 show the difference of passive and flash thermography obtained at impact and tensile loaded CFRP plates, respectively. As one purpose of these investigations is the development of standards within national (DIN) and European (CEN) standardisation bodies, new draft and final standards are presented and further needs are discussed at the end of the presentation.