Filtern
Dokumenttyp
Sprache
- Englisch (24) (entfernen)
Schlagworte
- OTDR (7)
- Optical fiber sensor (6)
- POF sensors (6)
- Polymer optical fibers (POF) (6)
- Strain sensor (6)
- Distributed sensor (5)
- Distributed strain sensor (5)
- Fiber optic sensors (5)
- Structural health monitoring (5)
- Geotextiles (4)
Eingeladener Vortrag
- nein (2)
We characterize the Brillouin gain spectra (BGS) in perfluorinated graded-index polymer optical fibers (PFGI-POFs) at 1.32 µm and 1.55 µm. Three kinds of PFGI-POFs with the same core diameter, but which are fabricated by different manufacturers, are tested. For all the PFGI-POFs, the Stokes power measured at 1.32 µm is higher than that at 1.55 µm due to the lower propagation loss, but significant differences in Stokes power are observed among the three. Based on the measurement obtained by the optical time-domain reflectometry, we show that the actual propagation loss of the PFGI-POFs plays a crucial role in observing BGS.
Structural health monitoring by distributed fiber optic sensors embedded into technical textiles
(2012)
Technical textiles with embedded distributed fiber optic sensors have been developed for the purposes of structural health monitoring in geotechnical and civil engineering. The distributed fiber optic sensors are based on Brillouin scattering in silica optical fibers and OTDR in polymer optical fibers. Such 'smart' technical textiles are used for reinforcement of geotechnical and masonry structures. The embedded fiber optic sensors provide online information about the condition of the structure and about the occurrence and location of any damage or degradation.--------------------------------------------------------------------------------------------------------------------------------------------------------
Technische Textilien mit integrierten faseroptischen Sensoren eröffnen neue Möglichkeiten der Zustandsüberwachung (structural health monitoring) in Geotechnik und Ingenieurbau. Die verteilt messenden Sensoren basieren auf der Brillouin-Streuung in Glasfasern und auf der OTDR in polymeroptischen Fasern. Derartige 'intelligente' technische Textilien werden in erster Line zur Verstärkung von geotechnischen Bauwerken und von Gebäuden genutzt. Die integrierten Sensoren liefern eine zeitnahe Information über den bestimmungsgemäßen Zustand des Bauwerks sowie über die Entstehung und den Ort von lokalen Bauwerksschäden.
We present the status of our work on a tube shaped 3D deformation sensor based on continuously distributed fiber optic sensing. A sensor tube of very large diameter is used to ensure high sensitivity while the transportability and applicability are still comfortable due to our application strategy. The setup is designed to use different measurement techniques in the applied optical fibers including Brillouin based measurements and interferometric optical frequency domain measurements using an OBR 4400 from Luna Technologies.
Fiber optic sensors based on polymer optical fibers (POF) have the advantage of being very elastic and robust at the same time. Unlike silica fibers, standard PMMA POF fibers can be strained to more than 40% while fully maintaining their light guiding properties. We investigated POF as a distributed strain sensor by analysing the backscatter increase at the strained section using the optical time domain reflectometry (OTDR) technique. This sensing ability together with its high robustness and break-down strain makes POF well-suited for integration into technical textiles for structural health monitoring purposes. Within the European research project POLYTECT (Polyfunctional textiles against natural hazards) technical textiles with integrated POF sensors, among others sensors are being developed for online structural health monitoring of geotechnical structures. Mechanical deformation in slopes, dams, dikes, embankments and retrofitted masonry structures is to be detected before critical damage occurs. In this paper we present the POF strain sensor properties, reactions to disturbing influences as temperature and bends as well as the results of the different model tests we conducted within POLYTECT. We further show the potential of perfluorinated graded-index POF for distributed strain sensing with increased spatial resolution and measurement lengths.
We investigate the suitability of silica graded index multimode fibers (MMF) for distributed Brillouin sensing in structural health monitoring, where the measurement range is limited by small bendings that appear during the integration process of the sensing fibers into the structures. For the investigation of stimulated Brillouin scattering (SBS) in MMF, we use an MMF connected on both ends to the SMF measurement setup by fusion splices to ensure that only the fundamental mode is transmitted. The SBS spectra in MMF are recorded using a 1319 nm single frequency (line width 5 kHz) laser. Results found for standard singlemode fibers and the fundamental mode in multimode silica optical fibers are compared. We present the gain spectra showing the dependence of frequency shift, attenuation and modal noise to both temperature and strain. The dependence of the attenuation due to bending is shown. Finally, the perspective of the excitation of SBS in polymer optical fibers is discussed against the background of our research on SBS in MMF.
Sensing characteristics of polymer optical fibers (POF) are studied using the optical
time-domain reflectometry technique. For the first time to our knowledge, investigations are
carried out with respect to integration of POF in technical textiles for distributed measurement
of mechanical deformation. The research on this new sensor type focuses on its application in
monitoring of geotechnical structures such as railway embankments, dikes, slopes and dams.
We report on a distributed sensor system using POF integrated in technical textiles as sensing
elements for measurement of displacement of soil. This sensor system is very robust it
withstands the integration under rough condition at a construction site and can detect strain
of more than 40 % over distances of more than 100 meters.
Fiber optic sensors based on polymer optical fibers (POF) take advantage of the high elasticity and high break-down strain of POF. Because of their outstanding elastic properties, POF are well suited for integration into technical textiles like geotextiles and medical textiles. Smart textiles with incorporated POF sensors, able to sense various mechanical and physical quantities, can be realized. The integration of POF as a sensor into geotextiles for monitoring of displacement of soil is very attractive since POF can be used for distributed strain measurement of strain values of more than 40 %. An online monitoring of critical mechanical deformations of geotechnical structures like dikes, dams, slopes, embankments as well as of masonry structures can be ensured. Medical textiles that incorporate POF sensors can control vital physiological parameters like respiratory movement and can be used for wearable health monitoring of patients requiring a continuous medical assistance and treatment. The biocompatibility of POF is an important criterion for selecting POF as a medical sensor. The paper shows selected examples of using POF sensors for the mentioned monitoring purposes.