Filtern
Dokumenttyp
- Zeitschriftenartikel (13) (entfernen)
Sprache
- Englisch (13)
Schlagworte
- Additive manufacturing (7)
- Residual stress (6)
- Neutron diffraction (3)
- IN718 (2)
- Laser powder bed fusion (2)
- Residual stress analysis (2)
- AGIL (1)
- Additive Manufacturing (1)
- AlSi10Mg alloy (1)
- As-built LPBF IN718 alloy (1)
- Bragg-edge neutron 2D imaging (BENI) (1)
- Coordinate measurement machine (1)
- Crystallographic texture control (1)
- Diffraction-elastic constants (1)
- Distortion (1)
- Distortion upon baseplate removal (1)
- Effect of scanning strategies (1)
- Electron backscatter diffraction (EBSD) (1)
- Electron backscattered diffraction (1)
- Heat treatment (1)
- IN718 PBF-LB/M (1)
- Inconel 718 (1)
- Kernel average misorientation (1)
- L-PBF (1)
- L-PBF IN718 material (1)
- LPBF (1)
- Laboratory X-ray diffraction (1)
- Laser-based additive manufacturing (1)
- Metal additive manufacturing (MAM) (1)
- Microstructure and texture (1)
- Near-surface X-ray diffraction (1)
- Neutron and X-ray diffraction (1)
- Nickel-based superalloys (1)
- Principal stress (1)
- Projekt AGIL - Alterung additiv gefertigter metallischer Materialien und Komponenten (1)
- Residual Stress (1)
- Residual stress in AM (1)
- Residual stress state (1)
- Residual stresses (1)
- SLM (1)
- Scan strategies (1)
- Scan strategy influence (1)
- Selective laser melting (1)
- Stainless Steel (1)
- Strain-free lattice references (1)
- Strain-free lattice spacing (1)
- Stress balance (1)
- Stress balance condition (1)
- Synchrotron X-ray diffraction (1)
- Texture (1)
- X-ray and Neutron Diffraction (1)
- X-ray and neutron diffraction (1)
Organisationseinheit der BAM
- 8.5 Röntgenbildgebung (13) (entfernen)
Laser based powder bed fusion additive manufacturing offers the flexibility to incorporate standard and userdefined scan strategies in a layer or in between the layers for the customized fabrication of metallic components. In the present study, four different scan strategies and their impact on the development of microstructure, texture, and residual stresses in laser powder bed fusion additive manufacturing of a nickel-based superalloy Inconel 718 was investigated. Light microscopy, scanning electron microscopy combined with electron backscatter diffraction, and neutron diffraction were used as the characterization tools. Strong textures with epitaxially grown columnar grains were observed along the build direction for the two individual scan strategies. Patterns depicting the respective scan strategies were visible in the build plane, which dictated the microstructure development in the other planes. An alternating strategy combining the individual strategies in the successive layers and a 67◦ rotational strategy weakened the texture by forming finer microstructural features. Von Mises equivalent stress plots revealed lower stress values and gradients, which translates as lower distortions for the alternating and rotational strategies. Overall results confirmed the scope for manipulating the microstructure, texture, and residual stresses during laser powder bed fusion additive manufacturing by effectively controlling the scan strategies.
The relationship between residual stresses and microstructure associated with a laser powder bed fusion (LPBF) IN718 alloy has been investigated on specimens produced with three different scanning strategies (unidirectional Y-scan, 90° XY-scan, and 67° Rot-scan). Synchrotron X-ray energy-dispersive diffraction (EDXRD) combined with optical profilometry was used to study residual stress (RS) distribution and distortion upon removal of the specimens from the baseplate. The microstructural characterization of both the bulk and the nearsurface regions was conducted using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). On the top surfaces of the specimens, the highest RS values are observed in the Y-scan specimen and the lowest in the Rot-scan specimen, while the tendency is inversed on the side lateral surfaces. A considerable amount of RS remains in the specimens after their removal from the baseplate, especially in the Y- and Z-direction (short specimen Dimension and building direction (BD), respectively). The distortion measured on the top surface following baseplate thinning and subsequent removal is mainly attributed to the amount of RS released in the build direction. Importantly, it is observed that the additive manufacturing microstructures challenge the use of classic theoretical models for the calculation of diffraction elastic constants (DEC) required for diffraction-based RS analysis. It is found that when the Reuß model is used for the calculation of RS for different crystal planes, as opposed to the conventionally used Kröner model, the results exhibit lower scatter. This is discussed in context of experimental measurements of DEC available in the literature for conventional and additively manufactured Ni-base alloys.
The residual stress distribution in IN718 elongated prisms produced by Selective Laser Melting was studied by means of neutron (bulk) and laboratory X-ray (surface) diffraction.
Two deposition hatch lengths were considered. A horizontal plane near the top surface (perpendicular to the building direction) and a vertical plane near the lateral surface (parallel to the building direction) were investigated. Samples both in as-built (AB) condition and removed (RE) from the base plate were characterized.
While surface stress fields seem constant for AB condition, X-ray diffraction shows stress gradients along the hatch direction in the RE condition. The stress profiles correlate with the distortion maps obtained by tactile probe measurements.
Neutron diffraction shows bulk stress gradients for all principal components along the main sample directions. We correlate the observed stress patterns with the hatch length, i.e. with its effect on temperature gradients and heat flow. The bulk stress gradients partially disappear after removal from the baseplate.