Filtern
Dokumenttyp
Referierte Publikation
- nein (5) (entfernen)
Schlagworte
- Ignition source (2)
- 20L-sphere (1)
- Alternative Energy Sources (1)
- Dust Explosions (1)
- Explodierender Draht (1)
- Exploding Wire (1)
- Hybrid Mixtures (1)
- Hybrid mixtures (1)
- Hybride Gemische (1)
- Inherent Scattering (1)
Organisationseinheit der BAM
There are several standardized ignition sources in use for the determination of explosion characteristics of gases, vapors and dusts. In the standards the ignition source is stated, but they vary in stating other characteristics like burning duration, energy or burning volume. Since heat is not visible under normal circumstances a Schlieren-Technique was used to make the full heating volume and not just the flames visible.
While an earlier paper of the authors focused on the ignition energy and burning duration of four standardized ignition sources, this paper focuses on the initial igniting volume, the ratio between initial igniting volume and the test-vessel size and other phenomena that were observed with the Schlieren-Technique-.
The article summarizes a short review of the literature focused on safety in the field of alternative energy sources. With an increasing orientation towards sustainable and renewable energy sources, new technologies will come to the fore. These facts must be demonstrated in occupational health and safety. Several studies focused on alternative energy sources are mentioned and show the trends for the future. Especially in the area of hydrogen and battery technologies, systems should pay attention to acquisitions as a normal part of our lives.
Safety research is essential for the acceptance of cleaner, efficient, and sustainable future.
Entwicklungen zu Bestimmungsverfahren für sicherheitstechnische Kenngrössen hybrider Gemische
(2020)
Zur Bestimmung sicherheitstechnischer Kenngrößen (STK) von hybriden Gemischen (Gemisch aus mindestens zwei brennbaren Phasen, wie z.B. Staub/Gas- oder Gas/Dampf-Gemisch) existieren bislang keine einheitlichen, genormten Prüfmethoden. Die Normen und Regelwerke zur Bestimmung der STK von einphasigen brennbaren Systemen (Staub, Gas, Dampf) unterscheiden sich teilweise erheblich. Beispielsweise sind in den jeweiligen Normen für Stäube, Gase und Dämpfe unterschiedliche Zündquellen und Zündenergien definiert. Des Weiteren unterscheiden sich die in den Normen definierten Prüfabläufe bei der Gemischherstellung. Bei der Entwicklung einer einheitlichen Norm für hybride Gemische muss der Einfluss dieser beiden Parameter ermittelt werden, um die Vergleichbarkeit mit den STK der einzelnen Komponenten Gas, Staub und Dampf gewährleisten zu können und bisherige Erkenntnisse zu hybriden Gemischen interpretieren und bewerten zu können.
For the determination of safety characteristics of gases, vapors and dusts different types of ignition sources are used in international standards and guidelines. Table 1 compares technical relevant ignition sources with their main features. The paper presents test results of a comparative calorimetric and visual study between four different types of ignition sources. The ignition procedures were analyzed visually with a high-speed camera and electric recordings. In addition to that, the influence of the electrode-orientation, -distance as well as ignition energy on the reproducibility of the exploding wire igniter was tested.
The exploding wire is already in use for standardized determination of safety characteristics of gases, first tests on the suitability of the exploding wire igniter for dust testing have been carried out by Scheid et al. Using the exploding wire, the ignition energy can be varied from 2 to 10 000 J (2 x 5 000 J) and thus it could be used for gases, vapors, dusts and hybrid mixtures. Moreover it can be used at high initial pressures and it is the only ignition source with an easily measurable ignition energy release. Furthermore, it does not introduce another chemical reaction into the system.
Finally, a proposal for a standard ignition source for explosion tests on hybrid mixtures is derived from the test results.
Safety characteristics are widely used in industrial processes to avoid explosive atmospheres (primary explosionprotection) or to mitigate the consequences of an explosion (constructive explosion protection). Several laboratory parameters influence the determined values when performing the test series such as the beginning pressure and the pre-ignition pressure rise, the ignition source, the ignition energy, the burning duration and volume or the concentration of the combustible substance.
In the different standards for the determination of safety characteristics of dusts there is no statement about the scattering or the deviation when parameters are chosen or occur on the borders of their allowed range. Thus, two laboratories might determine values that are hardly comparable for the same given substance.
This article summarizes some of the influential factors that cause a deviation and shows the inherent scattering of dust tests when all other parameters are kept constant. It also provides some advice how to minimize the deviation and the scattering with little effort.