Filtern
Erscheinungsjahr
- 2014 (4) (entfernen)
Dokumenttyp
Sprache
- Englisch (4)
Referierte Publikation
- ja (4)
Schlagworte
- Magnetic flux leakage (4) (entfernen)
Size adapted GMR arrays for the automated inspection of surface breaking cracks in roller bearings
(2014)
Their small size together with a remarkable field sensitivity are the most prominent features of present-day GMR sensors paving the way for various applications in automated non-destructive testing (NDT). This work presents a prototype for fast and automated magnetic testing of roller bearings. A local magnetization unit excites the magnetic field inside the bearing. As a result of a design study and the following wafer fabrication the probe was equipped with NDT-adapted GMR sensor arrays in which 48 elements measures the field response. The detection of artificial and 40 µm deep defects could be resolved with a SNR better than 20 dB. In addition, we report of first results of a POD (Probability of Detection) analysis using GMR sensors to investigate bearings with EDM (electronic discharge machining) notches having depths down to 10 µm. Finally, we estimate successfully the depth of a 57 µm notch from the measured data.
We present a prototype for automated magnetic stray field testing of ferromagnetic roller bearings. For this purpose NDE-adapted GMR sensor arrays (giant magneto resistance) are used for the detection of surface breaking cracks. The sensors are miniaturized down to the lower µm-regime to achieve adequate spatial resolution. In doing so, sensor arrays with up to 48 elements are used to inspect the bearing surface within a few seconds only. In contrast to magnetic particle inspection (MPI), where the global magnetization requires a further inspection step and succeeding demagnetization, the presented prototype only locally magnetize the surface area in the vicinity of the GMR Sensors. For the local magnetization, the applied sub-surface magnetic field was simulated and proofed for detecting flaws with a depth of a few 10 µm. By multiplexing the sensor array with an adapted read out electronics we quasi simultaneously detect the normal field component of about 100µm above the surface. The detection of artificial notches with a depth of 40 µm and more could be resolved with a SNR better than 20 dB. The presented testing facility is fast and provides a step towards automated testing of safety relevant steel components.
At BAM, the Federal Institute for Materials Research and Testing, a group of scientists develops NDT-applications based on GMR sensor technology. In particular, the knowledge gained in the field of automated testing systems based on the magnetic flux leakage (MFL) were combined with GMR sensors to achieve high resolution testing of ferromagnetic materials.
In cooperation with Europe's second largest steel producer, Tata Steel Europe, BAM is working on solutions for the detection of small inhomogeneities in thin steel plates. The objective is to incorporate an automated testing facility in a production line.
Before setting up an automated testing system, a feasibility study was carried out in order to verify the ability of GMR-MFL-testing and eddy current testing (ET) for the detection of hidden defects in thin steel plates. For this purpose, Tata Steel Europe fabricated in a first step test samples of 0.2 mm thick steel plates in which defects of different depth (5 – 60 µm) were introduced. Only in case of GMR-MFL-testing, we were able to detect parts of the hidden defects trustworthily with a SNR better than 10 dB. The lift off between sensor and surface was 250 ìm. On this basis, we investigated different testing scenarios including velocity tests and different lift offs. The achieved results for this special testing problem were presented leading to a practical example for GMR-based testing and paving the way to an automated testing system in a production line.
We present a simulation study which pursues the objective to find probe geometries for a MR-based eddy current (EC) probe (MR magneto resistance, e.g., GMR giant magneto resistance, TMR tunnel magneto resistance). MR sensor technology exhibits two significant advantages compared with conventional coil systems. First, MR sensors are relatively frequency-independent within common EC-frequency ranges which enable us to operate them in hidden defects testing problems. Secondly, MR technology is well suited for miniaturization helping us to design small elements in the order of below 100 µm. In this paper simulation and experimental results obtained with the probes for low frequency application, i.e. for hidden defects detection are discussed.
Our simulations are based on two different approaches for a better validation, a commercial finite element method software (Opera, Vectorfields) and the semi-analytical software CIVA. We investigated both coil arrangement in order to excite sufficient high eddy currents inside the test samples and position of MR-elements at the array chip. In doing so the MR sensors were positioned that they are not exposed to excitation fields. In addition, different coil geometries, in particular coil length, e.g. Ι = 20 mm, were analyzed in order to generate a consistent eddy current distribution beneath an array of up to 32 MR-elements. To prove obtained probe principles we built GMR-EC-probes. The first test measurements are in good agreement with the simulations performed by BAM and CEA. On basis of our findings the IMAGIC consortium developed new MR-EC-probes using integrated ASIC technology.