Filtern
Erscheinungsjahr
Dokumenttyp
Referierte Publikation
- ja (61) (entfernen)
Schlagworte
- GMR (11)
- Magnetic flux leakage (7)
- Ferroelectret (5)
- Non-destructive testing (5)
- Cellular polypropylene (4)
- Reconstruction (4)
- Sensor array (4)
- Ultrasonic testing (4)
- Active thermography (3)
- FEM (3)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (3)
- 8.4 Akustische und elektromagnetische Verfahren (3)
- 5 Werkstofftechnik (2)
- 5.2 Metallische Hochtemperaturwerkstoffe (2)
- 9 Komponentensicherheit (2)
- 5.1 Mikrostruktur Design und Degradation (1)
- 7 Bauwerkssicherheit (1)
- 7.1 Baustoffe (1)
- 8.5 Röntgenbildgebung (1)
- 9.2 Versuchsanlagen und Prüftechnik (1)
Ultrasonic investigation of inhomogeneous anisotropic materials such as austenitic welds is complicated because its columnar grain structure leads to curved energy paths, beam splitting and asymmetrical beam profiles. A ray tracing model has potential advantage in analyzing the ultrasonic sound field propagation and there with optimizing the inspection parameters. In this contribution we present a 2D ray tracing model to predict energy ray paths, ray amplitudes and travel times for the three wave modes quasi longitudinal, quasi shear vertical, and shear horizontal waves in austenitic weld materials. Inhomogenity in the austenitic weld material is represented by discretizing the inhomogeneous region into several homogeneous layers. At each interface between the layers the reflection and transmission problem is computed and yields energy direction, amplitude and energy coefficients. The ray amplitudes are computed accurately by taking into account directivity, divergence and density of rays, phase relations as well as transmission coefficients. Ultrasonic sound fields obtained from the ray tracing model are compared quantitatively with the 2D Elastodynamic Finite Integration Technique (EFIT). The excellent agreement between both models confirms the validity of the presented ray tracing results. Experiments are conducted on austenitic weld samples with longitudinal beam transducer as transmitting probe and amplitudes at the rear surface are scanned by means of electrodynamical probes. Finally, the ray tracing model results are also validated through the experiments.
Polypropylene based ferroelectret films exhibit a strong electromechanical activity and provide a promising solution for the air coupled ultrasonic (ACUS) transducers. Ultrasonic transmission between two air coupled ferroelectret transducers in dependence on the amplitude and polarity of the high voltage exciting pulse revealed a strongly non-linear electromechanical response of the ferroelectret transmitter which provides an increase in the transmitter efficiency. The authors present a simple model describing both promotion and competition of the piezoelectric and electrostriction contributions, as well as increase in the transducer constant under high voltage excitation. Enlargement of the inverse transducer constant of the polypropylene ferroelectret film by a factor of 4 was demonstrated. The non-linear properties of the polypropylene ferroelectrets result in a strong increase in their ACUS figure of merit under the high voltage excitation, which exceeds the results of their technological optimisation. Consequently, enhancement of the ACUS system transmission by 12 dB and signal to noise ratio by 32 dB was achieved.
Fast defect parameter estimation based on magnetic flux leakage measurements with GMR sensors
(2011)
We present a fast inverse scheme that is capable of simultaneously estimating the parameters depth, opening and length for rectangular 3D geometries of surface-breaking defects. The parameter estimation is realized by an iterative least-squares minimization using the trust-region reflective algorithm. A semi-analytic magnetic dipole model that allows the sensor characteristics to be incorporated is used for predicting the stray magnetic fields. Giant magneto-resistance (GMR) measurements were carried out on a test specimen that includes a series of artificial defects. For the estimation of the defect depths relative errors between 0.6% and 15.9% have been obtained. Due to its very low computational costs, the inverse scheme can suitably be employed in automated production environments.
Active thermography is a nowadays widely used NDT method making use of thermal material properties for defect detection. Basically, the sample is heated and the resulting surface temperature is recorded by an IR camera. For laser thermography a laser is used to heat the sample locally. The resulting spherical heat flow allows the detection of voids in arbitrary orientation. In this work, a method is presented which is suitable for the quantitative characterization of depth and angle of surface cracks. The main idea is to evaluate the crack-caused asymmetries of the laser's thermal footprint. The heat is introduced at fixed reference positions relative to the crack. In this paper a data analysis procedure is presented which allows the crack depth and angle to be described by only two characteristic scalar parameters. By investigating artificial test specimens with spark eroded notches, the feasibility of this method is validated. Furthermore, the behavior of the characteristic parameters with variations of crack angle, depth and experimental conditions is studied systematically by FEM simulations, showing that these parameters are well behaved.
The structures and properties of silver selenide samples strongly depend on the method of preparation. Thin films prepared by pulsed laser deposition (PLD) contain lamellae of two low-temperature modifications of Ag2Se whose structures were analyzed in detail by electron microscopy techniques. Besides the stable and known Naumannite-type phase (LT1), a metastable phase was observed (LT2), and the phase transformation was examined in situ. Via cooling and annealing, LT2 becomes dominant in thin films, thus enabling solving the structure of LT2 by electron diffraction. These experiments and HRTEM point to an Acanthite-type (stable low-temperature modification of Ag2S) structure of LT2. Rapid-quenching procedures were applied for the first synthesis of LT2 as bulk sample. Depending on the conditions of melt spinning experiments, well-defined products were formed. In one series, we found a separation of LT1 and LT2 into distinct morphologies, i.e. microspheres and dendrites, respectively. The results on the magnetoresistance of the rapidly quenched materials support previous work.
Impulse and lock-in thermography have been applied to detect delaminations of prototype solder joints, similar to those to be produced between Cu shunts and Cu busbar stabilisers at the Large Hadron Collider (LHC) at CERN. Two infrared cameras with different detector materials and with different spectral ranges and two excitation techniques have been tested and compared for their ability to detect delaminations behind 2 and 3 mm thick Cu shunts. We have analyzed the signal to noise ratio (SNR) for each detected defect and are able to detect defects down to a nominal edge length of 4 mm behind 2 mm thick Cu shunts by using fast impulse thermography and a camera with a microbolometer array. For the 3 mm thick Cu shunt, on the other hand, the nominal 4 mm defect is only visible in the lock-in thermography phase images and the highest SNR has been achieved with a cooled InSb-based camera. In addition, numerical simulations show the influence of the minimum detectable defect size on the shunt thickness and that the developed on-site testing technique is sufficient to find all defects that are detectable theoretically.
Ferroelectrets are promising materials for air-coupled ultrasonic transducers. A transducer made of polarized cellular polypropylene, including its electronic interface, was developed and compared with conventional air-coupled probes. Test pieces of fiber-reinforced polymer containing impact flaws and flat-bottom holes were inspected in transmission. The ferroelectret transducers achieved a considerably higher signal-to-noise ratio. The impacts were clearly visible with all transducers, but less noisy with ferroelectret transducers. The flat-bottom holes were better detectable than with a conventional probe with about the same focus size.
Ultrasonic examination of anisotropic inhomogeneous austenitic welds is challenging, because of the columnar grain structure of the weld leads to beam skewing and splitting. Modeling tools play an important role in understanding the ultrasound field propagation and optimization of experimental parameters during the ultrasonic testing of austenitic welds as well as the interpretation of the test results. In this contribution, an efficient theoretical model based on the ray tracing concepts is developed to calculate the ultrasonic fields in inhomogeneous austenitic welds quantitatively. The developed model determines the ultrasound fields by taking into account the directivity of the ray source, the inhomogenity of the weld as well as ray transmission coefficients. Directivity of the ray source in columnar grained austenitic materials (including layback orientation) is obtained in three dimensions based on Lamb's reciprocity theorem. Ray energy reflection and transmission coefficients at an interface between two general columnar grained austenitic materials are calculated in three dimensions. The ray tracing model predictions on inhomogeneous austenitic weld material are compared against those from CIVA, a commercial non-destructive modeling and simulation tool. The ultrasonic modeling tools in CIVA are based on semi-analytical solutions. For beam propagation simulation, a so-called 'pencil method' is used, which involves modeling the probe as a set of individual source points, each radiating 'a bundle' of diverging rays into the medium and integrating those elementary contributions. Inhomogenity in the weld region is approximated by mapping the grain orientations on weld macrograph. Simulation results for ultrasonic field profiles for an austenitic weld are shown to be in good agreement with the corresponding experimental results.
Spot welding is one of the most important technologies for joining sheet metal. While there are lot of approaches to non-destructive testing, quality assurance still mainly relies on welding parameter monitoring and destructive testing, leading to significant failure rates. In this paper an approach to spot weld testing using flash thermography is presented. The main focus of attention is on the identification of two typical error classes: stick welds and welds at the splash limit. Besides investigating the principal feasibility of thermography for zinc plated samples the results of a series test of spot welds joining 1 mm thick TRIP steel are shown. Based upon these results a statistical criterion is developed which allows a reliable classification of the named error classes.
Für die luftgekoppelte Ultraschall-Prüfung wird der Prototyp eines neuartigen Prüfkopfes vorgestellt. Statt eines piezokeramischen Ultraschall-Wandlers mit einer λ/4-Anpassschicht wird eine Ferroelektret-Folie aus schaumförmigem Polypropylen eingesetzt. Durch die außerordentlich geringe akustische Impedanz der Folie reduzieren sich die Reflexionsverluste an den Grenzschichten zur Luft so stark, dass bei diesem Prüfkopf auf eine λ/4-Anpassschicht verzichtet werden kann. Außerdem ist die Folie hochspannungsfest. Sie konnte mit Spannungen von mehr als 3500 V angesteuert werden und erlaubte eine Vorspannung am Ultraschall-Wandler des Empfangsprüfkopfes von 2000 V. Mithilfe der hohen Anregungsspannung stieg die Amplitude des akustischen Prüfimpulses auf das 11,2-Fache. Die Empfindlichkeit des Empfängers erhöhte sich durch die Vorspannung weiter um den Faktor 4,3. Insgesamt steigt die Amplitude am Empfänger also auf das 48-Fache, bei gleichbleibendem Rauschpegel. Ein abschließender Vergleich mit kommerziellen Luftultraschall-Prüfköpfen belegt die Überlegenheit der Folien-Prüfköpfe. Damit rückt der Einsatz einer vollwertigen Impuls-Echo-Technik auch bei der luftgekoppelten Ultraschallprüfung deutlich näher.