Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (54) (entfernen)
Sprache
- Englisch (47)
- Deutsch (5)
- Mehrsprachig (1)
- Polnisch (1)
Schlagworte
Organisationseinheit der BAM
We demonstrate (and are the first to do so) 63 km Brillouin Optical Frequency-Domain Analysis (BOFDA) for temperature and strain monitoring using a 100 km fiber loop. The use of BOFDA for long-range applications can be considered a novel approach, as previous investigations focused on the utilization of Brillouin Optical Time-Domain Reflectometry and Analysis (BOTDR and BOTDA, respectively). At 51.7 km, a 100 m hotspot (37 °C) was detected without using distributed Raman amplification or image processing.
We present, to our knowledge for the first time, a 100-km Brillouin Optical Frequency-Domain Analysis (BOFDA) employing a 200-km fiber loop. Compared to our previous publication, enhanced sensor length, sensor accuracy and spatial resolution are presented. The performance improvements are achieved by applying distributed Raman amplification (DRA) and a digital high-pass filter. We report on temperature measurements over sensing distances of 75 km and 100 km both with a 12.5-m spatial resolution. Temperature changes of 5 °C have been measured along 75 km sensing fiber. A temperature change of 30 °C has been detected at 99.5 km.
We present a novel technique based on incoherent optical frequency domain reflectometry (OFDR) to measure length changes quasi-distributed between reflection points in optical fibres. The technique enables length changes to be measured with a resolution better than 1 µm and allows for static and dynamic measurement capabilities up to 2 kHz. We demonstrate that dynamic measurements of multiple fibre sections can be conducted independently from each other with high precision. Due to the precise and dynamic measurement capabilities, the proposed sensor system is expected to open new fields of application, especially in the structural-health-monitoring sector. Possible applications are discussed in the paper.
Application of Intensity-Based Coherent Optical Time Domain Reflectometry to Bridge Monitoring
(2022)
Although distributed fiber sensing techniques have been widely used in structural health monitoring, the measurement results of bridge monitoring, particularly under destructive testing, have rarely been reported. To the best of our knowledge, this paper is the first report of distributed vibration measurement results, which we obtained during a three-day destructive test on an abolished bridge. A coherent optical time domain reflectometry (COTDR) was used to acquire the vibration information while the bridge was being sawed. The obtained signal was analyzed in time and frequency domain. Some characteristics of the sawing-induced vibration were retrieved by the short-time Fourier transform; the vibration exhibited several high frequency components within the measured range up to 20 kHz and all the components appeared in the same time slot. Some unexpected signals were also detected. Thorough analysis showed that they are quite different from the sawing-induced vibration and are believed to originate from internal damage to the bridge (probably the occurrence of cracks).
Application results of a dynamic technique for simultaneous measurement of length changes and optical power changes between multiple reflection points in an optical fiber are presented. The technique is based on incoherent optical frequency domain reflectometry (I-OFDR) and allows for measuring for example length changes and optical power changes quasi-distributed at repetition rates up to 2 kHz. Precise measurement with length change resolutions in the µm-range can be conducted using standard single-mode or multi-mode fibers. Previous results of dynamic refractive index change measurement and the use of polymer optical fibers for high-strain measurement are concluded and possible sources of measurement inaccuracies are discussed. Field test results with sensors installed on a masonry building during a seismic shake test are presented. The versatility and simplicity of this technique makes it potentially interesting for application in the structural health monitoring sector and chemical process control.
In this study, a signal processing approach for heterodyne Փ-OTDR and C-OTDR systems that can obtain external perturbation and its frequency content in a faster way is proposed. We can detect vibrations with the same or better SNR using this processing approach, only with a single step and fast calculation. Fig. 12 shows the comparison of the normalized measurement time for the gamma matrix method and the conventional method throughout the three experiments. The speed of processing using a gamma matrix is ~35%–50% faster compared to a conventional method in high frequency test (PZT), low frequency test (walking) and street monitoring test. The processing speed in low frequency test is normally a bit lower than the similar high frequency one, since we must use higher number of time frames. Also, in street test we have higher speed because we can select wider gauges.
A novel DAS setup based on geometric phases in coherent heterodyne detection is applied for the first time to the characterisation of the Earth’s subsurface. In addition, an optimisation of the proposed setup in terms of its spatial resolution is also presented for the first time. The surface waves are generated by strong blasts of 25 kg of explosives at a dedicated test site. A 10 km dark fiber link in the vicinity of the test site connected to the test setup records the resulting strain signals. The spike-free and low-noise strain data thus obtained minimize post-processing requirements, making the setup a candidate for real-time seismic monitoring. An analysis of the dispersion characteristics of the generated surface waves is performed using a recently reported optimised seismic interferometric technique. Based on the dispersion characteristics, the shear wave velocities of the surface waves as a function of the depth profile of the Earth’s crust are determined using an optimised evolutionary algorithm.
Bond monitoring in temperature dependent applications using Brillouin optical time domain analyser
(2016)
Adhesive bond has to be evaluated for its integrity over a range of temperature. Adhesive is being used to bond the sensors with structures. There is no validated technique to test its performance. In this paper, we propose a Brillouin Optical Time Domain Analyzer (BOTDA) based methodology to detect temperature-induced adhesive bond failure below room temperature using distributed fiber optic sensor. The differential coefficient of thermal expansion of the structure and fiber sensor can lead to bond failure at low temperature. Optical fiber impregnated in the structure will experience differential temperature/strain due to debond of the adhesive. This leads to the frequency and amplitude decomposition of the Brillouin spectra. This is a good indication for real-time monitoring of the integrity of a bond.
We characterize the Brillouin gain spectra (BGS) in perfluorinated graded-index polymer optical fibers (PFGI-POFs) at 1.32 µm and 1.55 µm. Three kinds of PFGI-POFs with the same core diameter, but which are fabricated by different manufacturers, are tested. For all the PFGI-POFs, the Stokes power measured at 1.32 µm is higher than that at 1.55 µm due to the lower propagation loss, but significant differences in Stokes power are observed among the three. Based on the measurement obtained by the optical time-domain reflectometry, we show that the actual propagation loss of the PFGI-POFs plays a crucial role in observing BGS.
Phase-sensitive optical time domain reflectometry (φOTDR) is an excellent distributed fiber sensing technique and has been applied in various areas. Its noise is however never been comprehensively studied to the best of our knowledge. The different detection noise sources in such a sensing system are thoroughly investigated. The impacts of thermal noise, shot noise and the beat between signal and the amplified spontaneous emission from a pre-amplifier have been theoretically and experimentally demonstrated. Due to the random nature of the φOTDR signal, the detection noise demonstrates distinct features at different fiber positions in a single measurement. The theoretical analysis and the experimental result explicitly affirm most of the fiber sections, and the difference at some positions may be explained by ambient noise.