Filtern
Dokumenttyp
- Zeitschriftenartikel (29) (entfernen)
Schlagworte
- Hybrid mixtures (4)
- Dust explosion (3)
- Dustiness (3)
- 20L-sphere (2)
- CFD (2)
- Cone calorimeter (2)
- Dispersion (2)
- Dust explosion protection (2)
- Dust explosions (2)
- Explosion protection (2)
Organisationseinheit der BAM
Paper des Monats
- ja (2)
Observed autoignition events and extinguishing the resulting smouldering fires in an underground storage system of a coal-fired power plant have provided insight into the array of contributing variables, and some experience on quantifying the risk with alternative scenarios of event initiation, progress and potential mitigation. Although the first attempts to quantify the risk suggest high sensitivity to the sequence of action taken after fire alarm, and no similar storage sites really exist, some recommended preventive, corrective and other mitigating activities can be at least partly defined and improved by using the cumulative experience and parallel efforts in other closed or underground storage sites. However, there are also so-called black (or at least grey) swans: unexpected events for which the facility may be poorly prepared for. In the case of the underground storage silos, such an event was experienced when incoming cold coal during a harsh winter season froze the sewer system that normally protects the stored coal from seepage water. With blocked normal bypass, the seepage water found its way to the coal silos and created large clumps of icy coal that blocked the coal conveyors. Although freezing weather is not unusual at high-latitude power plants, the common methods to combat freezing of coal are mainly useful for open storage sites and above-ground transport. Options for mitigation are discussed, as well as the event chain leading to an event that had never previously occurred. The case is discussed from the point of view of options to prepare for rare or unforeseen events.
A new safety characteristic the 'dustiness' according to VDI 2263 part 9 (Verein Deutscher Ingenieure, 2008) is investigated. Dustiness means the tendency of a dust to form clouds. The paper deals with the influence of the dustiness on vented dust explosions. In order to look into the effects of the dustiness on dust cloud formation and explosion properties experiments and simulations in a vertical dust dispersion glass tube apparatus were carried out.
Preliminary explosion experiments showed that the dustiness has an influence on the reduced explosion pressure in a vented 75 L test apparatus. Dusts with comparable pmax and KSt values and different dustiness were tested. Dusts with higher dustiness produced higher overpressures, despite comparable safety characteristics. In order to verify the results for applications in the process industries further tests with different settings are planned as well as industrial scale experiments. Characteristics of the dust such as particle size, density, specific surface area and particle shape, which influence the dispersibility, have been determined experimentally.
The Euler/Lagrange and the Euler/Euler approaches are compared for simulating an exemplary dust/air mixture. Especially sedimentation and the ability of the approaches to simulate the tendency of dust to stay airborne were investigated. The Euler/Lagrange approach is better suited for simulating local dust concentrations, particle size distributions and particle forces. It could be used to point out regions of high dust concentrations in a vessel. With the Euler/Euler method it is possible to achieve fast solutions for one specified diameter, but the simulated dust/air mixtures are always more homogenous than in reality. ANSYS CFX version 13 was used in all simulations.
Determination of measurement uncertainties in adiabatic hot-storage experiments for reactive dusts
(2013)
The formal kinetics of self-ignition of solid bulk materials theoretically can be derived from just one single adiabatic hot-storage test. The question arises how uncertainties in the measurements can be quantified and how these uncertainties affect the results of the subsequent predictions. Adiabatic and isoperibolic hot-storage basket tests were performed for samples of lignite coal, black coal, cork dust, a polymer dust, and wax-coated silicid acid. In the adiabatic experiments, the starting temperature and the temperature control of the oven were varied systematically to study the uncertainty margin of adiabatic tests. The apparent activation energy and the pre-exponential factor of the lumped reaction were derived from the adiabatic tests including average values and standard deviations and compared to isoperibolic experiments performed according to the European standard EN 15188. It could be shown that with a precise temperature control of the adiabatic oven combined with an automated computation of the maximum rate of temperature rise the uncertainty of the apparent activation energy can be limited to less than 10%.
Approaches towards a generic methodology for storage of hazardous energy carriers and waste products
(2013)
Energy carriers – either conventional or 'new' ones – have to be provided in large amounts to meet the requirements of permanent availability and reliable supply of electricity. Depending on their state of aggregation, energy carriers are either stored in large masses (if solid or liquid) or at elevated pressures (if gaseous). Both impose the hazard of large-scale fire, in the latter case additionally the danger of explosion or unintended release. Very similar hazards occur for wastes. Solid wastes are present in large masses and only a small part is recycled. Most of the solid wastes are used in energy conversion. The main gaseous waste is CO2. During capturing also the hazard of unintended release exists. In this article, existing approaches for safe storage and fire prevention are discussed and a generic methodology is outlined. This methodology consists of the following steps:
gaining knowledge about the behaviour of the material stored (reactivity, thermal stability, etc.),
assessing the environmental conditions for the storage site (neighbourhood, safety distances, etc.),
assessment of prospective consequences of an incident and
development of individual loss prevention conceptions.
All steps require both experimental testing and theoretical considerations about accident scenarios as integral parts of the methodology.
Minimum explosion concentration (MEC) of three agriculture dusts and two coal dusts was studied via a 20-L explosion chamber to reveal the role of gaseous inhibitors. Both active method (CO2 diluting air) and passive method (CO2 replacing O2) were used. The TG and DTG thermal analysis tests were conducted to study the pyrolysis and combustion characteristics of dust samples. An alternative explosion criterion based on combustion duration time was used to determine MEC, and compared with the standardized overpressure method. Under 10-kJ ignition condition, as oxygen mole fraction (XO2) decreased from 21% to 10%, MEC of agriculture dusts and coal dusts respectively increased by around 5 times and 2 times. The active inerting method with a lower N2/CO2 ratio was found to have a better suppression effect on the explosion of the five carbonaceous dusts because the blend has a higher specific heat and a lower oxygen diffusion rate.
In this study, 19 experiments were conducted with 25 pouch cells of NMC cathode to investigate thermal runaway and the release of gases from lithium-ion batteries (LIBs). Single cells, double cells, and a four-cell battery stack were forced to undergo thermal runaway inside an air-tight reactor vessel with a volume of 100 dm3 . The study involved two series of tests with two types of ignition sources. In the Series 1 tests, a heating plug was used to initiate thermal runaway in LIBs in the ranges of 80–89% and 90–100% SOC. In the Series 2 tests, a heating plate was used to trigger thermal runaway in LIBs in the ranges of 30–50%, 80–89%, and 90–100% SOC. Thermal runaway started at an onset temperature of 344 ± 5 K and 345 K for the Series 1 tests and from 393 ± 36 K to 487 ± 10 K for the Series 2 tests. Peak reaction temperatures ranged between 642 K and 1184 K, while the maximum pressures observed were between 1.2 bar and 7.28 bar. Thermal runaway induced explosion of the cells and lead to a rate of temperature increase greater than 10 K/s. The amounts of gases released from the LIBs were calculated from pressures and temperatures measured in the reactor.
Then, the gas composition was analyzed using a Fourier transform infrared (FTIR) spectrometer. The highest gaseous production was achieved at a range of 90–100% SOC and higher battery capacities 72 L, 1.8 L/Ah (Series 1, battery stack) and 103 L, 3.2 L/Ah (Series 2, 32 Ah cell)). Among the gases analyzed, the concentration of gaseous emissions such as C2H4 , CH4 , and C2H6 increased at a higher cell capacity in both series of tests. The study results revealed characteristic variations of thermal behavior with respect to the type of ignition source used.
There is no applicable existing standard for the determination of safety characteristics for hybrid mixtures. While developing a new standard in a joint research project in Germany first results from parameter studies led to a standard procedure that can be adopted by laboratories that are already testing dusts in the so called 20L-sphere with as little additional effort as necessary. In fact, one of the main objectives of this research project was to keep modifications and adjustments from the generally accepted dust testing procedures as easy and minimal as possible so as to limit potential deviations from one laboratory to another.
In this first round robin test on hybrid mixtures ever, with methane as gas component and a specific corn starch as dust sample, the practicality of the whole procedure, the scattering of the results and the deviation between the testing apparatuses is investigated. This paper summarizes the experimental procedure adopted and objectives of the first round-robin phase involving three of the four original German companies, plus volunteering laboratories from Australia, Belgium, Czech Republic, France, Poland and P.R. China. The results will have an impact on the new standard and may lead to robust data for later simulation purposes.
The explosion characteristics of anthracite coal dust with/without small amount of CH4 (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (Pex) and the rate of explosion pressure rise ((dp/dt)ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N2 with CO2, suggesting that CO2 has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH4 moderates the inhibition effect of CO2 and the promotion effect of O2 on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH4 mixture explosions, Barknecht’s curve was found to be more accurate and conservative than Chatelier’s line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.
The production of materials with dimensions in the nanometre range has continued to increase in recent years. In order to ensure safety when handling these products, the hazard potential of such innovative materials must be known. While several studies have already investigated the effects of explosions (such as maximum explosion pressure and maximum pressure rise) of powders with primary particles in the nanometre range, little is known about the ignition temperatures and flame velocities. Therefore, the minimum ignition temperature (MIT) of metallic nano powders (aluminium, iron, copper and zinc) was determined experimentally in a so called Godbert-Greenwald (GG) oven. Furthermore, the flame velocities were determined in a vertical tube. In order to better classify the test results, the tested samples were characterised in detail and the lower explosion limits of the tested dust samples were determined. Values for the burning velocity of aluminium nano powders are higher compared to values of micrometre powd
ers (from literature). While MIT of nanometre aluminium powders is within the range of micrometre samples, MIT of zinc and copper nano powders is lower than values reported in literature for respective micrometre samples.
Quasi-static dispersion of dusts for the determination of lower explosion limits of hybrid mixtures
(2022)
Knowledge of explosion limiting concentration of explosible materials is necessary forthe design of explosion protection measures. Currently employed methods of testing MEC of a dust cloud or LEL of a hybrid mixture are based on arbitrary assumptionsand possess technical limitations that often lead to values of MEC/LEL, which are unrealistically low or poorly reproducible. This contribution presents an improved method for experimental determination of MEC of a combustible dust cloud or LEL of a flammable gas or hybrid mixture. The new setup operates under laminar conditions and allows a uniform suspension of dust particles in an open top acrylic glass tube. Dust concentration is measured with the help of infrared sensors installed a few centimeters above and below the ignition source. In order to evaluate the dependence of MEC on flow front velocity, MEC of lycopodium was determined at four flow velocities. The results show that the flow field intensity does not significantly influence the MEC of lycopodium for the flow ranges tested in this work. Moreover, LEL of hybrid mixtures of lycopodium and methane was also tested at flow velocities of 4.7 cm/s, 5.8 cm/s, 7 cm/s and 11 cm/s and compared with the values obtained from other sources. The results suggest that the requirement of high energy pyrotechnical igniter may be relinquished, provided that a truly homogeneous suspension of dust particles could be achieved. Moreover, the effect of relative amount of dust and gas, on the course of ignition and flame propagation in hybrid mixtures at their LEL, was studied by the help of high speed videos. For hybrid mixtures of carbonaceous dusts (like lycopodium) at their LEL, ignition occurs in the gas phase, however, flame propagation is only possible through a two-way interaction of dust and gas during the course of combustion.