Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (21)
- Zeitschriftenartikel (2)
- Buchkapitel (1)
- Vortrag (1)
- Posterpräsentation (1)
- Forschungsbericht (1)
Referierte Publikation
- nein (27) (entfernen)
Schlagworte
- Dust explosions (3)
- Brandlastberechnung (2)
- CFD (2)
- Explosionsschutz (2)
- Kenngrößen (2)
- Nanostäube (2)
- Nichtatmosphärische Bedingungen (2)
- Sicherheitstechnische Kenngrößen (2)
- Zündkriterium (2)
- ANSYS CFX (1)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
This paper describes a modified experimental setup for the test apparatus 20-L-Sphere (also known as 20-L Siwek Chamber), that enables the test samples to be kept under inert atmospheric conditions nearly until ignition. This setup was designed to allow the determination of safety characteristics of nano powders under most critical circumstances (e.g. minimisation of the influence of oxidation before the test itself). The aim of this modification was to determine, whether or not the current setup and procedures underestimate the explosion violence and ignitability of nano powders. For this purpose, two different methods, the so called inerting method and the modified method (using a special nozzle called mushroom nozzle) are used. Both methods are described in the paper. The work includes experimental results of micrometer dusts to validate the modified method. Moreover first results of nanometer iron and aluminium dusts are presented, which were kept at inert conditions until shortly before the ignition. The tested nano iron was found to react pyrophoric, as soon as it gets in contact with air, while the tested nano aluminium did not generally show such behaviour. Tests with nano aluminium using the inerting method revealed a higher pressure rise in comparison to the standard test procedure. This could suggest a different extent of passivation. To investigate this effect more closely, further testes with more nano powders are required.
In practice, occurring explosive dust/air mixtures are usually not homogeneous and in many cases do not spread over the whole enclosure. For the safety measure explosion venting, a smaller venting area might be sufficient as calculated according to venting standards (EN 14491 'Dust Explosion Venting Protective Systems'). The tendency of bulk materials to form dust clouds is not taken into account so far. To optimize the design of explosion protection measures, a new safety characteristic the so-called 'dustiness' (see VDI 2263 part 9 'Determination of Dustiness of Bulk Materials'.) could be useful. Dustiness means the tendency of dust to form dust clouds. There are six dustiness groups (DG) from one to six (one means little tendency to stay airborne, six the opposite). The paper describes first results on the reasons for different dustiness and on dust explosion venting for several dusts of different dustiness. A 75 L vertical tube apparatus for vented dust explosion experiments was created. Pressure, pressure rises and flame speeds were measured to evaluate the course of the dust explosions. In addition the paper includes CFD simulations (ANSYS CFX) about the possibilities to model the dust/air mixtures with the Euler/Lagrange approach. In order to simulate the settling of dust clouds more realistic the particle surface area was adjusted and the particle size distribution was taken into account. Results were compared to experimentally determined terminal velocities.
Determination of measurement uncertainties in adiabatic hot storage experiments for flammable dusts
(2012)
Experimentelle Untersuchungen zum Einfluss von Brandbeschleuniger auf den Verlauf von Raumbränden
(2013)
Es werden die Untersuchungsergebnisse für ein geeignetes Zündkriterium zur Bestimmung von Explosionsgrenzen bei nichtatmosphärischen Bedingungen vorgestellt. Dazu wurden für Anfangsdrücke bis 20 bar Zündversuche an den Explosionsgrenzen von CHL/Luft-, CaHg/Luft-, H2/Luft- und NHs/Luft-Gemischen in einem Autoklav mit Sichtscheibe durchgeführt. In der Auswertung wurden visuelle Zündkriterien und ein Druckschwellenkriterium miteinander verglichen. Weiterhin wurden Untersuchungen zum erforderlichen Mindesvolumen des Explosionsgefäßes in Abhängigkeit des Anfangsdrucks durchgeführt. Dazu wurden jeweils Zündversuche mit demselben Gemisch aus CH4 und Luft bei Anfangsdrücken bis 50 bar in Volumina zwischen 0,2 dm3 und 6,0 dm3 durchgeführt.
A controlled-atmosphere cone calorimeter that is built by modifying the Standard apparatus with the addition of a controlled-atmosphere chamber offers a time- and cost-saving approach for reaction-to-fire testing in vitiation- and ventilation-controlled atmospheres. Due to the design of the added enclosure no mechanical changes on cone calorimeter’s Standard ductwork are required. This offers some advantages but also important limitations. The design has an open connection between the outlet of the added enclosure and the cone calorimeter’s exhaust hood. Therefore, sufficient ambient air from the laboratory surroundings is drawn into the System to introduce effects which have the potential to affect test results significantly.
A procedure which is is suitable to consider physical effects of the ambient air on the calculation of the heat release rate is presented as well as initial results of an application towards toxic potency assessment. Signs for Chemical effects of the ambient air such as post reactions are shown but subject of an ongoing work.
The Fractional Effective Dose model was used to predict the fire smoke toxicity numerically. In this context fire tests were carried out for three different building materials: polyurethane, flame retardant polyurethane and polyvinyl chloride. The fire tests were performed for flaming and smoldering combustion. The aim of the fire tests was to determine the light extinction, the smoke density and the combustion products at varying oxygen concentrations, different temperatures and different irradiance levels. The fire tests were performed in the German DIN-tube and also in the Cone Calorimeter. Stoichiometric coefficients at varying oxygen concentrations and temperatures were determined from measurements. With these stoichiometric coefficients reaction equations were defined and implemented in the Computational Fluid Dynamics (CFD) program, ANSYS CFX. The implemented reaction equations were used to account for different ventilation and temperature conditions in the simulation. The fire and smoke propagation was calculated numerically with CFD in the room corner test geometry. Equations to account for toxicity and light extinction were also implemented and were used to analyse the toxicity and the optical properties of fire smoke with CFD.