Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (66) (entfernen)
Sprache
- Englisch (41)
- Deutsch (24)
- Mehrsprachig (1)
Schlagworte
- Wear (16)
- Friction (15)
- Reibung (10)
- Verschleiß (7)
- Relative humidity (6)
- Luftfeuchte (5)
- Silicon carbide (5)
- DLC (3)
- CVD (2)
- Ceramics (2)
- Diamond (2)
- Fretting (2)
- Humidity (2)
- Kohlenstoffschichten (2)
- Normalkraft (2)
- Oscillating sliding (2)
- Reciprocating sliding (2)
- Temperatur (2)
- Temperature (2)
- Titanium carbide (2)
- Titanium diboride (2)
- Verschleiss (2)
- Vibrating contacts (2)
- Water lubrication (2)
- AFM (1)
- Acoustic emission (1)
- Adhesion (1)
- Alumina (1)
- Bearbeitbarkeit (1)
- Ca-Ba fluoride (1)
- Calcium titanate (1)
- Calciumtitanat (1)
- Ceramic (1)
- Ceramic Composites (1)
- Ceramic composites (1)
- Chemical vapour deposition (1)
- Coating (1)
- Coating, debris (1)
- Corundum (1)
- Counter body material (1)
- Counterbody material (1)
- Cytokines (1)
- DLC-coatings (1)
- Database (1)
- Debris (1)
- Dental ceramic (1)
- Dentalkeramik (1)
- Depth-sensing indentation (1)
- Diamant-Beschichtungen (1)
- Diamond coatings (1)
- Diamond-like carbon (1)
- Dispersing behavior of particles (1)
- Dry-slidins (1)
- EDX (1)
- Elektrischer Widerstand (1)
- Feuchte (1)
- Frequency (1)
- Friction test (1)
- Hard coatings (1)
- High temperatures (1)
- Hip joint endoprostheses (1)
- Humidity water (1)
- Implant (1)
- Infiltration (1)
- Keramik (1)
- Kompositkeramik (1)
- Kontaktmechanik (1)
- LRS (1)
- Laserstrahlbearbeitung (1)
- Life time (1)
- Liquid media (1)
- Load (1)
- Lubrication (1)
- MW PACVD (1)
- Machinability (1)
- Macrophages (1)
- Mating material (1)
- Mechanical properties (1)
- Metalldotierung (1)
- Metalle (1)
- Microparticles (MP) (1)
- Model particles (1)
- Nano-particles (1)
- Nanoparticles (NP) (1)
- Normal force (1)
- Oberflächentopographie (1)
- Operational parameters (1)
- Oscillating Sliding (1)
- Oscillating sliding test (1)
- PECVD (1)
- Parameter effects (1)
- Particle size distribution (1)
- Particulate composite (1)
- Particulate composites (1)
- Polieren (1)
- Polishing (1)
- Porous zirconia (1)
- Preceramic polymer (1)
- Raman-Laser (1)
- Raman-Mikroskopie (1)
- Randzone (1)
- Reproduzierbarkeit (1)
- Role reversal (1)
- Roughness (1)
- Running in (1)
- Running-in (1)
- SEM (1)
- Schallemission (1)
- Scherenergiedichte (1)
- Schmierstoff (1)
- Schwingungsverschleiss (1)
- Schwingungsverschleiß (1)
- Si3N4 coating (1)
- SiC (1)
- SiO2 coating (1)
- Silicon nitride (1)
- Siliconcarbonitride (1)
- Siliziumkarbid (1)
- Slip-rolling (1)
- Solid lubrication (1)
- Stainless steel (1)
- Steel (1)
- Steel couples (1)
- Steel/diamond pairings (1)
- Stroke (1)
- Surface analysis (1)
- Surfaces (1)
- TEM (1)
- Test methods (1)
- Testdauer (1)
- Thermal resistance (1)
- Third body (1)
- Ti-6Al-4V (1)
- TiB2 (1)
- TiC (1)
- TiN (1)
- Titanium alloy (1)
- Titanium boride (1)
- Topography (1)
- Transfer layer (1)
- Tribo-oxidation (1)
- Tribobeanspruchung bei reversierendem Gleiten (1)
- Tribologie (1)
- Tribology (1)
- Tribooxidation (1)
- Tribotesting (1)
- Unlubricated friction (1)
- Verbundwerkstoffe (1)
- Verschleißprognose (1)
- Wear debris (1)
- Wear particle (1)
- Wear products (1)
- Wear scar (1)
- Wires (1)
- Zwischenmedium (1)
- pH-Wert (1)
- pH-value (1)
- ta-C coatings (1)
Diamantähnliche Kohlenstoffschichten (DLC) zeichnen sich durch ein sehr günstiges Reibungs- und Verschleißverhalten aus. Auf vielen Werkzeugen und hochbelasteten Bauteilen ist DLC daher bereits erfolgreich im Einsatz. In naher Zukunft wird die Bedeutung dieser Schichten als Oberflächenschutz in tribologischen Systemen weiter ansteigen.
Wie viele Applikationsbeispiele zeigen, ist die Leistungsfähigkeit von DLC als Schicht zur Verringerung von Reibung und Verschleiß zwar groß, weist aber auch Grenzen auf. Vor allem bei höheren Temperaturen (> 300 °C) treten Strukturveränderungen oder sogar Oxidationsvorgänge auf, die auch die tribologischen Eigenschaften der Schichten verschlechtern können.
Reibungs- und Verschleißuntersuchungen (Schwingungsverschleiß) von DLC-Schichten wurden im Temperaturbereich von 25 °C bis 250 °C durchgeführt und zeigen ein schnelleres Durchreiben der Schicht bei höheren Temperaturen. Die Lebensdauer der Schichten wird mit zunehmender Prüftemperatur reduziert. Einsatzgrenzen für DLC-Schichten können abgeleitet werden.
Tribological characterisation of siliconcarbonitride ceramics derived from preceramic polymers
(2006)
Amorphous SiCN ceramics were prepared in a laboratory scale as disk shaped specimens with 10 mm diameter and 0.3 mm thickness. The friction and wear behaviour was characterised in gross slip fretting tests under unlubricated conditions at room temperature against steel (100Cr6) and ceramic (Al2O3). Tests with a ball-on-disk contact were performed in laboratory air with different content of water vapour. The results show clearly that the relative humidity has a significant effect on friction and wear behaviour. All tests in dry air lead to higher friction and higher wear rate than in normal air. Improved friction and wear behaviour was observed with increasing pyrolysis temperature up to 1100 °C of the SiCN specimens. This is attributed to increasingly better mechanical properties and higher stiffness of the amorphous network due to the evaporation of gaseous organic species and the formation of free graphite like carbon.
Amorphous SiO2 and Si3N4 plasma-enhanced chemical vapour deposited (PECVD) coatings were deposited on two different substrate materials (fused silica and borosilicate glass), with three coating thicknesses (0.1, 0.5, and 1.0 µm). The mechanical properties (hardness and elastic modulus) were determined by depth-sensing indentation, with loads from 700 mN down to 0.1 mN. Tribological behaviour was studied in instrumented oscillating sliding tests at room temperature with a ball-on-flat arrangement, in which the coated disc was tested against an alumina ball, at a load of 1 N. Interpretation of the measurement of hardness and modulus of the coatings has to take into consideration the influence of layer thickness and the effect of the substrate. Tensile film stress and crack generation were only observed for Si3N4 on fused silica above a threshold thickness. Friction and wear measurements show that the coating has an effect on friction, while wear is affected by the thin coatings only for a short running-in phase. The morphology of the wear scars indicates that the coatings have good adhesion. Despite crack generation, delamination effects were not observed. Indentation patterns similarly showed excellent lateral homogeneity of the mechanical properties over the entire film surface, and indicated that load-displacement curves may be used to characterise the system.
Tribological screening tests (simple, reciprocating ball-on-flat tests) were performed with the objective to identify an appropriate coating for the articulating surfaces of artificial hip joints whose acetabular cups and femoral stems are made from Ti6Al4V alloy, which is appreciated for its light weight, good biocompatibility and elastic properties similar to those of natural bone. Standard coatings like TiN or CrN performed better than more complicated multi-layer systems, though not as good as different types of amorphous carbon coatings, generally referred to as diamond-like carbon or DLC coatings. Among the latter, hydrogenated amorphous carbon (a-C:H) displayed the best properties, especially if the hydrogen content was increased by reducing the bias voltage during PA-CVD-deposition.
The optimised a-C:H coating revealed the most promising wear behaviour under the applied testing conditions, i.e. the increase of linear wear with the number of cycles was close to zero. Regarding the materials examined in this study, correlation of wear with mechanical properties obtained by nano-indentation revealed that high hardness was not an adequate criterion for selecting appropriate coatings. A high ratio of hardness and elastic modulus (H/E) proved to be more important. Microstructural and micro-analytical investigations revealed transformation of TiN and CrN to TiO2 and Cr2O3, respectively, and amorphous carbon was, at least partly, transformed to graphite. Furthermore, incorporation of Al2O3 from the ball was observed at a very fine scale. The wear debris of favourable coatings always formed agglomerates of nano-scale particles. It was shown that commercial nano-particles of Al2O3, Cr2O3 and carbon black are comparable to particles generated by the tribological tests. However, it is uncertain whether they are comparable to those formed during simulator studies or in vivo. Furthermore, the performance of the favourable coating has to be tested in a hip joint simulator before its potential for application in prostheses can be assessed.
Diamond like carbon (DLC)-coatings are applied very successfully on computer discs. Sliding friction tests confirm their high performance as dry lubricants with friction coefficients (COFs) below 0.1. In contrast to sliding tests, until very recently most of the DLC-coatings failed in slip-rolling test after fewer cycles than uncoated samples. However, present tests with DLC-coatings of seven different suppliers show a more promising tribological behaviour under slip-rolling conditions. The DLC-coatings were deposited onto steel 100Cr6, HRC 60, with a thickness of 23 ?m. The counter bodies were uncoated, grinded or polished 100Cr6 discs with 30 mm radius of curvature. The tests were performed on a twin disc testing rig (Amsler type) with paraffin oil under boundary/mixed lubrication and rolling with 10% slip. The initial, average Hertzian contact pressure was adjusted to Pm = 1.0, 1.25, and 1.5 GPa. The failure criterion was defined as the occurrence of a single damaged area larger than 1 mm2, which was controlled by optical microscopy (OM). An acoustic emission (AE) measurement system was installed as an additional online control for coating failure. The stressed coatings and the chipping areas were analyzed by OM, SEM, EDX, AFM and Raman spectroscopy.
Until now, the results reveal that a large scatter in lifetime of coatings occurs not only between samples of different coaters but also between the samples of one single batch. The highest lifetime reached by a DLC-coating under these testing conditions is 10 × 106 cycles. That is the highest life time for a coating tested under the testing conditions above in our laboratory so far. The following factors were identified to influence the life time of the coatings: coating thickness, interlayer type, topography of the coatings, counter body roughness and mechanical properties. But the most important factor determining the life time of the coatings is that the coating process does produce homogenous layers free of faults.
Contact formation and development are the basis of friction and wear modelling and understanding. Unanimously topography formation and development in friction contacts are regarded of highest importance for understanding and modelling friction processes. The frequently found running in behaviour of sliding contacts is—aside from the build up of reaction and transfer layers-at least partly caused by the topography development due to friction processes until a stable equilibrium state is reached.
Experimental results of friction and topography measurements are presented which demonstrate the mutual modification of friction and contact topography.
A special experimental set up with an AFM allowed to correlate the measured friction forces with the contact position and the topography at this point. In this way, friction force transitions and changes can be assigned to topography changes due to abrasion, adhesion and wear particle agglomeration.
Contact surfaces with artificial regular structures have been prepared to avoid problems with topography and friction correlation due to the statistical nature of roughness on technical contact surfaces. The friction effects of roughness were simulated by etched ditches of defined width, depth and distance on silicon or metal surfaces. This allowed to explain the mutual influences of topography and friction. The effect of a single asperity and of the 'roughness structures' could be demonstrated.
Topography measurements with an AFM correlated with the friction force could help to understand friction changes without changing any parameter.