Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Sammelband (28)
- Vortrag (25)
- Beitrag zu einem Tagungsband (24)
- Zeitschriftenartikel (16)
- Posterpräsentation (4)
Sprache
- Englisch (78)
- Deutsch (18)
- Mehrsprachig (1)
Referierte Publikation
- nein (97) (entfernen)
Schlagworte
- Ablation (5)
- Femtosecond pulse laser (4)
- Laser processing (3)
- Micromachining (3)
- Femtosecond-Pulse Laser (2)
- Laser (2)
- Lasersicherheit (2)
- Semiconductors (2)
- Silicon (2)
- Acoustical measurement (1)
Eingeladener Vortrag
- nein (25)
Abstract Femtosecond laser micromachining has excited vivid attention in various industri-
al fields and in medicine owing to the advantages of ultrashort laser pulses compared to
long-pulse treatment.These are mainly the reduction of the laser fluence needed to induce
ablation and the improvement of the contour sharpness of the laser-generated structures.
Recently,special attention was paid to femtosecond laser experiments on nonabsorbing in-
organic dielectrics.This is due to the fact that optical damage in dielectric optical elements
limits the performance of high-power laser systems.Despite the fact that a large variety of
organic polymers can be machined with excimer lasers successfully,the involvement of
thermal processes can lead to an unsatisfactory quality of the structures.Ultrashort,fs-laser
pulses might be an alternative for the treatment of polymers.Therefore,femtosecond laser
machining investigations of dielectrics and polymers are reviewed in this paper.Similarities
and differences of the ablation behavior of both material classes are discussed.The influ-
ence of the bandgap on the ablation threshold in dependence on the pulse duration,the en-
hancement of the machining precision with a shortening of the pulse duration,incubation
phenomena,and morphological features appearing on the surface after femtosecond laser
treatment are mentioned.Possible applications,e.g.,in medicine and biosensors,are de-
scribed.
The removal and accelerated corrosion monitoring of metal coating systems is of general interest in materials science
and engineering technology. The femtosecond and nanosecond laser ablation and delamination at 800 nm and 532 nm,
respectively, of anodic oxide layers on aluminium alloys in electrolyte contact were investigated. Laser-induced
modifications of the oxide layer resulted in an ionic contact between electrolyte and metal, which produced a current
transient and thus allowed the in-situ electrochemical monitoring of the modification. Oxide coatings with different
optical properties, almost transparent and opaque, were examined. The transparent anodic oxides showed contrasting
ablation mechanisms in the nanosecond and femtosecond pulse duration regime: nanosecond pulses caused spallation,
whereas femtosecond treatment led to ablation. Current signals measured in the transparent film were consistent with
light absorption below the metal-oxide interface and with film spallation. Irradiation of the opaque coating yielded ionic
current transients within the so-called shock-affected-zone of the oxide layer. This investigation provided insight into the
role of the penetration depth of light and the heat-affected zone, the extent of the shock-affected zone, and the defect
formation in the coating and at the solid-solid interface between metal and oxide.
Ultra-short pulse laser seeding techniques for silicon crystallite growth on amorphous substrates
(1999)
In this paper, safety-related experiments with ultra-short laser pulses (down to 30 fs) on various components
(goggles, curtains) for laser protection are presented. The damage and failure behaviour of
protective devices has been investigated dependent on practical conditions such as pulse duration, laser
.uence, pulse number, and repetition rate.
The e.ects of laser-irradiation on materials can be roughly divided into transient ones like laserinduced
transmission (LIT) or short-lived colour centres and permanent damages like the stable colour
centres and ablation. The former e.ects are particularly important for transparent devices like laser
goggles.
To obtain a complete overview on laser safety issues and the prevention of failure there are two
important .elds of investigation:
1. the e.ects of laser radiation on human eyes and skin, and
2. on the possible protection materials.
Both .elds have been addressed during the recently .nished German project SAFEST (safety aspects
in femtosecond technology). The amount of safety data available in the ultrashort pulse region has
been increased remarkably. This allows for a re-evaluation of known laser protection materials for this
region of pulse durations and for the evaluation of new designs that promise high protection levels
while being light-weight and convenient to use.