Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (64) (entfernen)
Sprache
- Englisch (36)
- Deutsch (22)
- Mehrsprachig (6)
Schlagworte
- Rheology (14)
- Rheologie (6)
- Cement (5)
- Concrete (5)
- Betoninstandsetzung (4)
- Geopolymers (4)
- Instandsetzung (4)
- Self-compacting concrete (4)
- Alkali-activation (3)
- Beton (3)
Organisationseinheit der BAM
Paper des Monats
- ja (2)
Grouted connections are intensively used in offshore rigs, platforms as well as jacket and monopile offshore wind turbine structures. Being located in remote offshore conditions, these connections can experience considerable adverse loading during their lifetimes. Degradation was reported inside similar connections, which were installed in the last three decades. Grouting in the offshore sites may often be proven difficult, which eventually leads to reduced load-bearing capacity of connections in the long run. Thus, repair and rehabilitation of such connections should be planned ahead to minimize operational delays and costs. In this study, scaled grouted connections were manufactured using a novel mould, whose integrity were monitored using digital image correlation (DIC). The connections were loaded under static load to visualize the main failure pattern using distributed fibre optic sensors and acoustic emission (AE) analysis. Grouted connections were then repaired using a cementitious injectable grout. The effectiveness of the grout injection was monitored using dye penetration technique. Finally, specimens are reloaded to identify the potential of such repair for grouted connections.
Superplasticizers (SPs) have been employed in concrete technology for decades to improve the workability of concrete in its fresh state. The addition of SPs in cement-based systems affects the early properties. Although the interaction of the cement particles with various SPs has been extensively researched, there still exists limited research on the interaction of SPs with supplementary cementitious materials such as rice husk ash (RHA). This paper investigates the rheological properties and early hydration kinetics of RHA-blended systems with three types of SPs, a polycarboxylate ether (PCE) and two lignosulphonates (LS-acc and LS-ret). In rheological properties, the addition of SP causes an initial improvement of workability as the yield stress is significantly reduced. The pastes with PCE and LS-acc show a slight increase of yield stress over time whereas pastes with LS-ret tend to lower the yield stress slightly over time, further improving the workability. Without SP, pastes with RHA show a lower yield stress but an increase in plastic viscosity as cement is further replaced with RHA. The addition of the LS SPs is observed to lower the plastic viscosity but remains constant with further replacement of cement with RHA. This indicates that LS SPs further adsorbs on RHA particles and hydration products produced causing dispersion of the particles
within the system. In early hydration kinetics, pastes with PCE retard hydration and the degree of retardation is further increased with LS SPs. In the presence of RHA, the retardation of LS SP systems is significantly reduced. The pastes with PCE show more ettringite in the SEM micrographs, but is observed to be shorter needles. This indicates an initial good workability for PCE. However, C-S-H and CH were observed to be low in quantity, whereby the pastes with LS show more nucleation sites for C-S-H and CH. The ettringite needles in the LS systems were similar in quantity and more elongated in some cases but not abundant as in the PCE systems.
Design : and use of engineered recycled mineral admixtures obtained from industrial and mineral waste are promising strategies to increase the range of materials suitable for use in cement-based composites. In this work, Portland cement-blended pastes containing mineral admixtures designed for improving particle packing were evaluated in the presence of low- and high-charge polycarboxylate-based superplasticizers. The powders were obtained from basic oxygen furnace slag, iron ore tailings, quartz mining tailings, and quartzite mining tailings. The zeta-potentials of the particles were obtained via electrophoretic mobility. The flow properties were evaluated by rheological tests performed in a Couette type rheometer. The hydration kinetics was evaluated by isothermal calorimetry and an adapted method based on the Vicat needle test. The high-charge PCE and the finer mineral admixtures produced more stable blends. Coarser mineral admixtures led to increased flowability and delayed hydration compared to finer ones. Steel slag powders presented the most significant plasticizer effects, but also the largest setting delays and segregation tendency. Quartz-rich superfines reduced the setting delays caused by the superplasticizers. In summary, both superplasticizers were effective in improving flow properties, but the high-charge PCE was effective in preventing segregation in pastes containing mineral admixtures coarser and heavier than cement.
Rice husk as (RHA) is an eco-friendly material, which can be used as a supplementary cementitious material (SCM) in cement and concrete. Due to the high water demand for the material, superplasticizers (SPs) are essential to improve the performance. However, the interaction between the SPs and RHA systems is limited. This paper investigates the interaction of the binders with three SPs, i.e. two polycarboxylate ethers (PCEs) and one lignosulphonate (LS). The investigations are performed on blended systems of mortar containing various percentages of RHA and limestone powder (LSP). LSP is used in this research to improve the workability of the mortar. The results from the zeta potential (ZP) shows that the SPs are extremely dependent on the pH of the suspension. At higher pH values such as in a cementitious system, the ZP becomes less negative indicating that the ions in the suspension interact with the carboxyl groups in the backbone of the polymers thus reducing the surface charges of the SP. The mini-slump flow shows that the workability of the blended mortar systems is significantly improved with the addition of SPs. LS systems with increasing RHA is observed to have similar workability as the control mix over time. The compressive strength test results show increased strength for all mortar specimens with added RHA and LSP at later ages.
The fresh behaviour of self-compacting concrete (SCC) at varying temperatures differs from that of normal vibrated concrete. This is because the rheology of SCC depends not only on degree of cement hydration, but also on the adsorption of superplasticizers – mostly polycarboxylate based polymers (PCE) -, which is affected by the time and hydration progress. Due to the variety of PCEs and mixture compositions for SCC a prediction of the rheology at varying temperatures is complicated. The charge densities of PCEs as well as the water to solid ratio in the paste are identified to be the main decisive parameters for robust fresh concrete properties.
Rheometric concrete investigations with different SCC mixture compositions and varied anionic charge densities of the PCE were conducted. SCC which is rich in powder components showed robust performance at low temperatures while SCC with low powder content was favourable at high temperatures. High charge density PCE pointed out to be very robust at low temperatures but at high temperatures it significantly reduced the flow retention. Low charge density PCE could not generate self-compacting properties at low temperatures but retained the flow performance over sufficiently long time. Based on considerations about particle interactions and adsorption mechanisms of PCEs, the relevant processes are explained and options for the development of robust mixture compositions for individual temperature ranges are itemised.
Worldwide an increasing migration from rural to urban regions can be observed. Hence cities are growing and as a result the building density and the land sealing rise. Concrete as commonly used building material in urban structures provides a high heat storage capacity. Therefore the microclimate in cities has become warmer than in the surrounding areas. This phenomenon is called Urban Heat Island Effect. To mitigate this situation a large scale application of self-cooling concrete pavers is an approach to reduce the urban heat island effect. Making use of evaporation enthalpy, this new type of pavements counterbalances the absorption of solar radiation and the subsequent transfer of heat to the surrounding environment. The typical double-layer structure of concrete paving stones can be maintained. The mass concrete acts as a water storage layer and is covered by a permeable face concrete. As the different requirements of these layers demand different concrete mixtures, they are developed and optimised for their respective functions. This paper presents some suitable no-slump concrete mixtures that combine a sufficient compressive strength as well as good water transportation properties for the above mentioned approach.
To design robust self-consolidating concrete (SCC) for various environmental conditions, it is essential to understand the relevant mechanisms that control the flow performance. This paper depicts how high range water reducing agents (HRWRAs) interact with clinker and hydration phases, and it discusses the important role of the charge density of polycarboxylic HRWRAs in the way the rheology is affected. Based on the rheometric investigations on SCC mixture compositions with different water to powder ratios (w/p) and observations of their pastes' Vicat setting times, the study shows that increasing charge densities of the HRWRA and decreasing w/p reduce the flow retention and have lesser retarding effect on the setting. Based on the test results and discussions optimization procedures for the mixture composition and the HRWRA modification are suggested to achieve optimized performance for varying environmental situations and highest robustness for specific conditions.
The study introduces the porous medium model for the simulation of concrete flow through highly-reinforced sections. It shows that numerical simulations can predict concrete behavior during casting and help to avoid expensive mistakes.
Polysaccharides provide high potential to be used as rheology modifying admixtures in mineral binder systems for the construction industry such as concrete or mortar. Since superplasticizers have become state of technology, today, concrete is more and more adjusted to flowable consistencies. This often goes along with the risk of segregation, which can be effectively avoided by adding stabilising agents supplementary to superplasticizers. Stabilising agents are typically based on polysaccharides such as cellulose, sphingan gum, or starch. Starch clearly distinguishes in its effect on rheology from other polysaccharides, mainly due to the strong influence of amylopectin on the dispersion and stabilisation of particles. Based on rheometric investigations on cementitious and limestone based dispersions with different volumetric water to solid ratios, the mode of operation of modified potato starch is explained in comparison to a sphingan gum. It is shown that the stabilising effect of starch in a coarsely dispersed system is mainly depending upon the water to solid ratio and that above a certain particle volume threshold starch mainly affects the dynamic yield stress of dispersions, while plastic viscosity is affected only to a minor degree. Sphingans operate more independent of the particle volume in a coarsely dispersed system and show significantly higher effect on the plastic viscosity than on the yield stress. In systems incorporating superplasticizers, influences of both stabilising agents on yield stress retreat into the background, while both observed polysaccharides maintain their effect on the plastic viscosity.
Seit Juli 2014 liegt die EN 206:2014 als neue Betonnorm vor. Neben kleineren Änderungen ergibt sich hierdurch als einschneidende Änderung zur Vorgängerversion EN 206-1:2008 ein ergänzendes Konzept zur Konformitätsbewertung der Druckfestigkeit von Beton. An dieser Stelle werden neben dem bekannten Mittelwertkriterium alternativ sogenannte Kontrollkartenverfahren möglich. Für die Konformitätsbewertung stellt in diesem Zusammenhang insbesondere die Kusum-Methode (kumulierte Summen, aus dem Englischen cusum – cumulative sum) ein Novum dar. Weiterführende Informationen zu Kusum-Methode in der Konformitätsbewertung können der Literatur entnommen werden. Eigentlich ist die Kusum-Methode aber nicht für die Konformitätsbewertung entwickelt worden, sondern vielmehr für die Produktionskontrolle. Der Unterschied zwischen Konformitätsbewertung und Produktionskontrolle ergibt sich daraus, dass die Konformitätskontrolle eine Bedeutung für die öffentliche Sicherheit hat und dass eindeutige technische Grenzwerte vorliegen müssen, die nicht unterschritten werden dürfen, während die Produktionssteuerung ein Werkzeug mit frei wählbaren Grenzwerten für Hersteller ist. Der Handlungsbedarf ist für die Produktionskontrolle optional und ergibt sich in der Regel aus Wirtschaftlichkeitsbetrachtungen.