Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (22)
- Beitrag zu einem Tagungsband (15)
- Beitrag zu einem Sammelband (11)
- Vortrag (8)
- Posterpräsentation (7)
- Sonstiges (1)
- Forschungsbericht (1)
Schlagworte
- Computed tomography (12)
- Computertomographie (6)
- Computer Tomographie (3)
- Fire resistance (3)
- Intumescence (3)
- Osteoporotic vertebral fracture (3)
- Simulation (3)
- X-ray refraction (3)
- Aerospace (2)
- Bone regeneration (2)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (8)
Die sehr gute Reproduzierbarkeit von tomographischen Messungen zusammen mit den digital vorliegenden Ergebnissen ermöglicht die zerstörungsfreie dreidimensionale quantitative Analyse der untersuchten Bauteile und Proben mit Methoden der Bildverarbeitung. Vorwiegend für den Nachweis von Poren eingesetzt, lassen sich mit CT auch unterschiedliche Materialbestandteile analysieren, wobei die einzige Voraussetzung ein hinreichender Unterschied (es genügen wenige Prozent) in den Röntgenabsorptionseigenschaften der zu unterscheidenden Bestandteile ist.
Mit den in der Bundesanstalt für Materialforschung und -prüfung entwickelten Computertomographieanlagen kann der Anteil von Hohlräumen und Materialbestandteilen einer Probe bestimmt werden, wobei die Größe der nachzuweisenden Bestandteile sich über mehrere Größenordnungen erstreckt.
An ausgewählten Beispielen aus den Bereichen Keramik, Bodenproben und Fahr-bahnübergangssystemen aus Asphalt werden die quantitativen Ergebnisse dargestellt und die in der Bestandteilanalyse erreichbare Genauigkeit diskutiert.
A novel 3D-CT scanner was set up at BAM to extend the applicability of the X-ray transmission microtomography (µ-CT) to specimens up to 30 cm in diameter. The scanner consists of a bipolar 320 kV micro focus tube and a flat panel detector of amorphous silicon. Minimisation of scattered radiation, control of room and system temperature, and corrective preprocessing on the projection data are necessary to achieve expectable CT images. Statistical evaluations to show the limits and results of CT investigations are reported.
Summary
Beside several favourable properties, like high specific strength and damping capacity, most magnesium alloys also exhibit an excellent castability and are therefore usually fabricated by high pressure die casting. Due to the high casting speed, the melt flow is non-laminar and air can be entrapped during the casting process causing porosity when the melt solidifies. The volume fraction of porosity can be up to 4%. Porosity highly influences the mechanical properties, reducing significantly the values of elongation, tensile strength and especially fatigue strength [1-5]. Additionally, no heat treatment is possible to reach the optimum mechanical properties of the material. An alternative casting technology to reduce porosity is the Thixomolding process where the material is cast in the semi-solid state.
Different methods of non-destructive testing are possible to detect and remove affected components to ensure using components with a low content of porosity. One alternative of evaluating the porosity is the computerized tomography (CT). The CT enables a 3-dimensional view of the cast component.
Drucksondierungen, teufengenaue Probenahme und Präparation MKW-kontaminierter Lockersedimente
(2000)
Metallische Schäume: Dichte, Porenverteilung und Verschiebungsfelder im 3D aus Microtomographiedaten
(2003)
Digitale Detektionssysteme in der Röntgentechnik - kenngrößen, Eigenschaften und Einsatzgebiete
(2003)