Filtern
Erscheinungsjahr
Dokumenttyp
Referierte Publikation
- ja (21) (entfernen)
Schlagworte
- Explosion (5)
- Explosionsgrenzen (4)
- Explosionsschutz (3)
- Explosion limits (2)
- Fire (2)
- Wasserstoffspeicherung (2)
- Acetylen (1)
- Acetylene (1)
- Acetylene cylinders (1)
- Adiabatsiche Verdichtung (1)
Organisationseinheit der BAM
In Gasphasen aus Ethylenoxid (EO) und Propylenoxid (PO), die bei technischen Alkoxylierungsreaktionen vorkommen, können auch ohne den Zutritt von Luft Zerfallsreaktionen stattfinden, die explosionsartig mit einer vielfachen Temperatur- und Drucksteigerung verlaufen. Zur Abschätzung der Auswirkungen solcher Explosionen wurden die Explosionsdrücke und die zeitlichen Druckanstiege von reinem EO und EO/PO-Gemischen bei Temperaturen von 100°C bis 200°C und Drücken von 1 - 10 bar in einem 3-dm³-Behälter und punktuell in einem 100-dm³-Behälter experimentell bestimmt.
Determination of deflagration venting requirements in chemical/process plants is usually carried out using well established standards employing an empirically based formula. However, this formula is shown to have severe shortcomings, especially in the range of low KG-values, where either negative or inconceivably large venting areas can be predicted. Due to these shortcomings a method has been developed using the efflux function for gases as a basis to predict the mass flow through a vent opening in a vessel during an internal explosion. The simulated rise in pressure due to the internal explosion is quantitatively determined from the KG-value, with the mass flow through the vent opening in the vessel resulting from the pressure difference between the vessel and its surroundings. This enables the maximum overpressure as a function of the pressure relief surface area to be predicted. The method takes into account the temperature of the efflux gases and turbulence enhancement brought about by the venting process. In the following paper explosion pressure relief experiments are described and the results from these experiments are compared to predictions from the efflux method. It is shown that by adjusting the assumed turbulence which evolves during the venting process, the reduced explosion pressure can be reasonably well reproduced.
The explosion of hydrogen gas storage cylinders on May 25, 1894, represents one of the most spectacular failure cases during the late industrialization period in Germany. With respect to modern applications to hydrogen storage as energy carrier, it has several times been referred to as precedent failure case for the whole industrial sector. The detailed investigation reports by Martens have thus gained interest in the last years, but also, because the publications in 1896 about his expertise already provided in September 1894 document one of the first and most comprehensive investigations which can be regarded as a nucleus for modern failure analysis.
After summarizing the newspaper reports in the introduction, the present contribution provides a review of Martens' reports targeted at the development of failure analyses and materials testing procedures as well as potential failure origins.
Preventing the explosion of acetylene cylinders involved in fire with help of numerical modeling
(2012)
The current paper describes a mathematical model, which was developed to simulate the heat transfer in acetylene cylinders during exposure to a fire. The cases of a direct engulfment of the cylinder in the flames and of exposure to a distant fire were considered. Furthermore, the model was also applied to the prediction of the heat transfer during the cooling with water of heated acetylene cylinders, in order to assess the effectiveness of this procedure as a measure to prevent the burst of the cylinder. To provide data for the definition and validation of the model a total of 13 bonfire tests with 8.9-, 10- and 50-dm³-cylinders were performed, where pressure and temperature measurements in the samples were performed. During 5 experiments the fire was extinguished before the expected cylinder burst and a cooling with water was applied. In the paper a short description of the experimental set-up and of the test results is given. Finally, a comparison with the model predictions is provided, showing reasonable agreement.
In this paper two different approaches for predicting the heating-up of an acetylene cylinder involved in a fire and the afterward cooling with water are presented. In the simulations polynomial functions were used to describe the temperature dependency of the thermal properties of the cylinder interior, which is a complex system composed by a solid porous material, a solvent (typically acetone) and acetylene dissolved in it. Model equations covered heat conduction in the cylinder interior and at its walls. In the first approach the cylinder surroundings were simulated as a further domain constituted by CO2, during the fire exposure, and for water, during the cooling. In this domain the coupled heat transfer (convection and conduction) and the momentum equation (Navier-Stokes) were solved. In the second approach no further domain was considered but boundary conditions were set directly on the cylinder walls. Results of the calculations performed with both approaches are presented. This work could prove helpful in predicting to which extent the interior of an acetylene cylinder exposed to fire reaches temperatures capable of initiating the decomposition of acetylene and to determine how long a water cooling should be applied, so that the system is brought again under non-critical conditions.
Messung und Simulation des Inertgaseinflusses auf Explosionsgrenzen bei erhöhten Anfangsdrücken
(2001)