Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (32)
- Zeitschriftenartikel (24)
- Beitrag zu einem Tagungsband (6)
- Sonstiges (5)
- Posterpräsentation (5)
- Beitrag zu einem Sammelband (1)
Schlagworte
- Mechanical properties (8)
- Haftfestigkeit (4)
- IIT (4)
- ISO 14577 (4)
- Instrumentierte Eindringprüfung (4)
- Nanoindentation (4)
- Instrumented indentation testing (3)
- Normung (3)
- Calibration (2)
- Dynamic testing (2)
Organisationseinheit der BAM
- 6 Materialchemie (9)
- 6.7 Materialsynthese und Design (8)
- 6.2 Material- und Oberflächentechnologien (2)
- 9 Komponentensicherheit (2)
- 9.5 Tribologie und Verschleißschutz (2)
- 5 Werkstofftechnik (1)
- 5.1 Materialographie, Fraktographie und Alterung technischer Werkstoffe (1)
- 6.1 Oberflächen- und Dünnschichtanalyse (1)
- 6.6 Physik und chemische Analytik der Polymere (1)
Eingeladener Vortrag
- nein (32)
Tribological screening tests (simple, reciprocating ball-on-flat tests) were performed with the objective to identify an appropriate coating for the articulating surfaces of artificial hip joints whose acetabular cups and femoral stems are made from Ti6Al4V alloy, which is appreciated for its light weight, good biocompatibility and elastic properties similar to those of natural bone. Standard coatings like TiN or CrN performed better than more complicated multi-layer systems, though not as good as different types of amorphous carbon coatings, generally referred to as diamond-like carbon or DLC coatings. Among the latter, hydrogenated amorphous carbon (a-C:H) displayed the best properties, especially if the hydrogen content was increased by reducing the bias voltage during PA-CVD-deposition.
The optimised a-C:H coating revealed the most promising wear behaviour under the applied testing conditions, i.e. the increase of linear wear with the number of cycles was close to zero. Regarding the materials examined in this study, correlation of wear with mechanical properties obtained by nano-indentation revealed that high hardness was not an adequate criterion for selecting appropriate coatings. A high ratio of hardness and elastic modulus (H/E) proved to be more important. Microstructural and micro-analytical investigations revealed transformation of TiN and CrN to TiO2 and Cr2O3, respectively, and amorphous carbon was, at least partly, transformed to graphite. Furthermore, incorporation of Al2O3 from the ball was observed at a very fine scale. The wear debris of favourable coatings always formed agglomerates of nano-scale particles. It was shown that commercial nano-particles of Al2O3, Cr2O3 and carbon black are comparable to particles generated by the tribological tests. However, it is uncertain whether they are comparable to those formed during simulator studies or in vivo. Furthermore, the performance of the favourable coating has to be tested in a hip joint simulator before its potential for application in prostheses can be assessed.
An attempt was undertaken to obtain a better understanding of the tribological properties of two wear-resistant coatings on tool steel by structural and microchemical analysis of wear particles using a transmission electron microscope. Coatings were deposited by physical vapor deposition and plasma-assisted chemical vapor deposition techniques and tribological properties were derived from reciprocating sliding tests of the coatings against alumina balls. Three types of wear particles were identified by electron diffraction and energy dispersive X-ray spectroscopy: nanocrystalline rutile (TiO2), nanocrystalline graphite and microcrystalline graphite. Low coefficients of friction, of the order of 0.2, were attributed to the formation of solid lubricant films of sub-stoichiometric TiO2-x Magnéli phases and/or graphite.
The chemical and microstructural changes occurring during braking simulation tests at the surface of a conventional brake pad material were investigated mainly by scanning and transmission electron microscopy and surface analytical techniques. It can be shown that patches of a third body material develop, comprising a compositional mix of all constituents of the pad and iron oxides from the disk. Milled debris particles still have the crystal structure of barite, the major phase of the pad material, but the grain size is reduced drastically to the nanometer scale. The major wear mechanism is delamination of filler particles from the organic binder, supported by local degradation of the phenolic resin during asperity heating. Quartz crystals are preserved thereby adopting the function of primary contact areas.
In the last years, a lot of research work has been performed in the field of surface coatings and thin films technology, often supported by governmental research programs, as i.e. in Germany, the Thin Film Technology and OSTec research programs. But up until now, there is still a lack in transfer of this large amount of knowledge created by research activities on to industrial application and commercialization. To overcome this problem, a new web based information system has been developed (http://www.schichttechnik.net), which in a first step will make the whole content of the German OSTec research program (approx. 180 research reports) of the last 10 years available. In further steps, data from products of coating suppliers and other research programs will be taken into account. The database contains the following sections: definition of the coating system, deposition equipment, deposition processes, application properties, test procedures and test equipment, information about standardization and base information about coating processes etc. It will be possible to search for coatings by material properties and functions of coatings, considering also restriction on the substrate. In addition, searching regarding combination of properties, e.g. for wear-resistant, conductive, decorative coatings etc. will also be possible.
Durch faseroptische Sensoren können Bauteile im Einsatz kontinuierlich überwacht und frühzeitig Informationen über Materialveränderungen gewonnen werden. Mittels einer magnetostriktiven Aktorschicht, welche den Sensor umhüllt, kann nun auch die korrekte Sensorfunktion jederzeit kontrolliert werden. Als Aktorschicht eignet sich galvanisch abgeschiedenes reines Nickel oder Nickel-Eisen in der Zusammensetzung 50:50. Um diese haftfest mit dem Sensor zu verbinden wurde ein ECD/PVD-Kombinationsschichtsystem entwickelt. Die mechanischen Eigenschaften der ECD-Schicht können sowohl mit einer auf die Fasergeometrie angepassten instrumentierten Eindringprüfung als auch einem 2-Punkt-Biegeversuch bestimmt werden.
Thin polybutadiene/polystyrene blend films were deposited on glass substrates by spin-coating. The two polymers were chosen, as they are immiscible and differ strongly in their mechanical properties. The blend was characterized with Tapping Mode and force–distance curves. Several advantages of force–distance curves measurements compared to Tapping Mode are shown, most of all the capability of yielding quantitative information about several properties, such as Young's modulus and adhesion. Also the aging behaviour of the blend exposed to air could be observed, in particular the increase of the Young's modulus due to cross-linking and dewetting processes. Additionally, the sample was used to improve the resolution of force–distance curves up to 6 nm, which is to date the best resolution achieved with force–distance curves. Such an improvement resolves the major disadvantage of force–distance curves, compared to other scanning mode, i.e. its inferior resolution.