Filtern
Erscheinungsjahr
- 2013 (11) (entfernen)
Dokumenttyp
- Beitrag zu einem Tagungsband (4)
- Zeitschriftenartikel (3)
- Buchkapitel (2)
- Vortrag (2)
Schlagworte
- Tribologie (3)
- Festschmierstoffe (2)
- MoS2 (2)
- Cryogenic temperatures (1)
- Humidity resistance (1)
- Hydrogen environment (1)
- Kryogene Temperaturen (1)
- Kryotechnik (1)
- Laser arc deposition (1)
- Low temperatures (1)
Eingeladener Vortrag
- nein (2)
Cryogenic solid lubrication
(2013)
The tribological behaviour of MoS2/ta-C double layer coatings deposited by Laser-Arc technology was investigated in vacuum and air. In vacuum environment, the friction coefficient against steel balls varies between 0.005 and 0.02 depending on the contact pressure. At high contact pressures, the friction coefficient is as low as 0.005 and the life time between 340,000 and 500,000 cycles. Furthermore, it is shown that a ta-C base layer improves the performance of MoS2 coating.
Surface analyses were performed before and after the tribological tests by means of SEM, EDX, XRD, and TEM. They show that in the top layer beneath the sliding surface crystallization of the initially quasi-amorphous MoS2 took place. TEM images also verified an orientation of the basal MoS2-lattice planes parallel to the surface.
MoS2 is a suitable solid lubricant for environments free of oxygen or water vapor (i.e. vacuum). Humid air degrades film properties due to oxidation accompanied by high wear and increasing coefficients of friction. The present study aims at the further development of sputtered pure MoS2 coatings, extending their applicability to varying environmental conditions by increasing the resistance against humidity. The systematic coating development process is supported by using an experimental Box–Behnken design with variations of the deposition parameters cathode voltage, target/substrate distance, temperature and argon gas pressure. In contrast to common one-factor-at-a-time (OFAT) studies, this approach enables a determination of interactions between deposition process parameters and tribological–mechanical MoS2 film properties. The tribological improvement focuses on a maximization of wear resistance in air and vacuum measured in ball-on-disk experiments. The evaluated mechanical properties are hardness, elastic modulus and residual stresses. These stresses were determined by the substrate curvature method. The study reveals that the residual stress state in the films and the hardness-to-modulus ratio are crucial for their tribological performance in humid air and vacuum environments. After a detailed determination of the relationships between deposition conditions and film properties, some selected microstructural analyses are presented which show that a substantially basal orientation of the lattice has positive effects on wear but also causes anisotropic film properties which result in fissile fracture of the coating if strong shock or point loads occur.
Der Festschmierstoff Molybdändisulfid ist insbesondere für Extremanwendungen ein gerne eingesetzter Werkstoff, problematisch ist jedoch der negative Einfluss von Feuchtigkeit. Bei mittels PVD-Verfahren abgeschiedenen MoS2-Schichten ergibt sich jedoch die Möglichkeit, durch Anpassung der Beschichtungsparameter vorwiegend basal ausgerichtete Schichten herzustellen, die auch an Luft ein verbessertes tribologisches Verhalten zeigen.
Superconducting magnets are susceptible to quenching, even with the smallest amounts of energy disturbances due to the extremely low thermal capacity of materials at 4.2 K. Hence, small mechanical disturbances resulting in frictional heating can be sufficient to exceed the wire’s critical temperature, causing it to quench. Unfortunately, relative motion between surfaces in the magnet System is inevitable due to various forces present in the System, including winding pretension, differences in material thermal contraction and the large electromagnetic forces. Typically insulating polymers are present at this interface to achieve the required electrical insulation requirements.
Ensuring a sustainable energy supply is currently one of the most important areas for industry and research institutions. Hydrogen technology is a promising candidate, but its broad extension requires extremely high reliability and safety in all areas for common applications as automobiles and stationary fuel cells. Particularly components containing tribosystems are critical parts.
Polymers are extensively used for sliding systems in cryogenic applications because of their favourable friction and wear behaviour in the absence of external lubrication. Since important new technologies are based on applications under extreme conditions, such as at low temperatures, new requirements on material properties, in particular regarding their operability and reliability, must be met. Up to now, most tribological investigations have been carried out in inert cryogens or cryogenic gas (He, N2). Few experiments have been performed in vacuum environment at cryogenic temperatures. Rarely were testing in reactive media, such as LH2 or LOX. Due to the wide range of operating conditions in cryogenic applications, it is difficult to state general rules. Therefore, this chapter tends to give an overview on theories and experimental studies on polymer tribology at cryogenic temperatures.