Filtern
Erscheinungsjahr
- 2013 (16) (entfernen)
Dokumenttyp
Sprache
- Englisch (16)
Schlagworte
- Aerosol-assisted DBD (3)
- Adhesion (2)
- Plasma polymerization (2)
- Polystyrene (2)
- Surface modification (2)
- Acrylic acid-styrene copolymer (1)
- Adhesion polypropylene-aluminium (1)
- Ageing of polyolefins (1)
- Aggregation (1)
- Analytik (1)
Mixtures of hexamethyldisiloxane (HMDSO) and oxygen have been used for deposition of SiO2-like layers by plasma polymerization under low-pressure conditions onto polyethylene and polystyrene used as basecoat. Water glass was cast onto these 0.5 µm plasma thick siloxane-like layers with a thickness of 5 to 40 µm. The adhesion of these bilayer systems and their flame resistance were tested.
The effect of different plasma parameters such as monomer/gas ratio, pressure and power input into the discharge on the deposition rate and the composition of the formed layers was studied. Characterization and chemical composition of the formed films were performed using infrared, X-ray photoelectron and solid state nuclear magnetic resonance spectroscopy.
Peel strengths of composites were measured and the locus of peel front propagation was detected. Thermal properties of composites were analyzed by thermo-gravimetric analysis. Finally, the fire-retardant properties of thick coated polymers were determined by exposure to flames and the behavior of coatings on the polymers during flaming was observed visually.
Degradation behavior of thin polystyrene films on exposure to Ar plasma and its emitted radiation
(2013)
Spin-coated films of amorphous polystyrene (PS) were exposed to argon plasma for a few seconds to several minutes. The PS film was either in direct contact with the plasma or was shielded from the direct plasma contact by filters with different cutoff wavelengths in the vacuum UV region or by a Faraday cage (FC) made from metal mesh to prevent the impinging of charged species. Only energy-rich neutrals and plasma radiation may be operative in presence of the FC. lithium fluoride (LiF) filter protects the sample from direct contact with the plasma. Wavelengths of plasma radiation shorter than c. 105 nm (≈ 11.8 eV) were cut off. Glass filters made of fused SiO2 have a cutoff at λ ≈175?nm completely the vacuum UV radiation of plasma (ca. 175 nm ≈ 7.0 eV). These energies are sufficient to produce C–C, C–H bond scissions in case of direct Ar plasma exposure and Ar plasma exposure with use of the LiF filter. Only quartz glass shielding did not produce significant effects on the polymer surface in comparison to the reference PS, either in surface energy or O/C ratio or in IR spectra. Oxygen plasma has worked most aggressive and had etched the PS film, thus establishing a steady state between introduction of new oxygen functionalities and polymer etching. Ar plasma exposure produces also oxidation and etching of the polymer films as the oxygen plasma. Using of a FC during Ar plasma exposure or the LiF filter a slightly weaker oxidation was observed.
Br bonding on plasma brominated graphite surfaces has been studied by using Near Edge X-ray Absorption Fine Structure (NEXAFS) and X-ray Photoelectron Spectroscopy (XPS). Br2 and bromoform were used as plasma gases in an r.f. cw low pressure plasma process. Kr plasma had been used to study separately the physical and chemical plasma etching effects. At early steps of plasma bromination which lead to only small XPS Br surface concentration values a quick decay of aromaticity has been observed. At low Br surface concentration radical or even electrophilic addition of bromine onto sp2 carbon atoms is discussed as the dominating reaction pathway. At higher Br surface concentrations the inherent formation of sp3 defects in the graphene network by chemical etching processes promotes nucleophilic substitution of bromine at sp3 carbons as a competing reaction pathway. Both reaction pathways lead to CBr species characterized by the same Br 3d XPS binding energy. However more than one Br 3d component in XP spectra has been found at lower Br2 plasma induced Br surface concentrations and complexation of bromine at HOPG is assumed as a third way of interaction with Br2 plasma.
Mixtures of hexamethyldisiloxane (HMDSO) and oxygen have been used for deposition of SiO2-like layers by plasma polymerization under low-pressure conditions onto polyethylene and polystyrene used as basecoat. Water glass was cast onto these 0.5 pm plasma thick siloxane-like layers with a thickness of 5 to 40 mu m. The adhesion of these bilayer systems and their flame resistance were tested. The effect of different plasma parameters such as monomer/gas ratio, pressure and power input into the discharge on the deposition rate and the composition of the formed layers was studied. Characterization and chemical composition of the formed films were performed using infrared, X-ray photoelectron and solid state nuclear magnetic resonance spectroscopy. Peel strengths of composites were measured and the locus of peel front propagation was detected. Thermal properties of composites were analyzed by thermo-gravimetric analysis. Finally, the fire-retardant properties of thick coated polymers were determined by exposure to flames and the behavior of coatings on the polymers during flaming was observed visually.
Brominated single-walled carbon nanotubes [(Br)n-SWCNT) produced by the plasma-chemical technique were involved in the liquid-phase process of hydrocarbons aerobic oxidation. The significant catalytic effect of the (Br)n-SWCNT was revealed at first by the cumene initiated model oxidation and then in experiments on profound aerobic oxidation of petroleum naphthenic fraction derived from the commercial Azerbaijan (Baku) oils blend diesel cut. The ability of (Br)n-SWCNT to accelerate the aerobic oxidation of the hydrocarbons was found out for the first time. Obviously this phenomenon originates from the peculiarities of electronic configuration of the (Br)n-CNT patterns. The plausible mechanism of (Br)n-SWCNT catalytic action is inclined to the formation of reactive oxygen species. The catalytic activity of (Br)n-SWCNT markedly exceeds the activity of the industrial catalysts, manganese salt of indigenous petroleum acids, used for the liquid phase petroleum hydrocarbons oxidation process.
A convenient way to overcome the chemical inertness of polyolefin surfaces is to expose them to the atmospheric air plasma of a dielectric barrier discharge (DBD). To improve the efficiency in formation of polar groups at the polyolefin surface, different liquids such as water and ethanol were sprayed as aerosol into the plasma zone between the powered electrode and the polyolefin surface. Both sprayed liquids as well as the polyolefin surface were simultaneously activated; thus, the formation of different functional groups at the polyolefin surface was realized. The type of aerosol-sprayed additive, exposure time, power etc. have been found to determine the efficiency with respect to introduction of polar groups.
Different surface treatments of polypropylene (PP) were tested to improve the peel strength of aluminium-PP systems. Plasma exposure followed by chemical grafting of spacers with -SiOH endgroups and thin adhesion promoting layers deposited by aerosol-assisted DBD using aqu. solutions of classic polymers were compared. Both methods were effective, however, –SiOH terminated spacers effected no peeling also after ageing.
Ultra-high molecular weight polyethylene membranes were modified and subsequently polymer coated using the underwater plasma produced by glow discharge electrolysis. This plasma pretreatment generated various O-functional groups among them OH groups have dominated. This modified inner (pore) surface of membranes showed complete wetting and strong adhesion to a hydrogel copolymerized by glow discharge electrolysis also. The deposited hydrogel consists of plasma polymerized acrylic acid crosslinked by copolymerization with the bifunctional N,N'-methylenebis(acrylamide). Tuning the hydrogel hydrophilicity and bio-compatibility poly(ethylene glycol) was chemically inserted into the copolymer. Such saturated polymer could only be inserted on a non-classic way by (partial) fragmentation and recombination thus demonstrating the exotic properties of the underwater plasma. The modification of membrane was achieved by squeezing the reactive plasma solution into the pores by plasma-induced shock waves and supported by intense stirring. The deposited copolymer hydrogel has filled all pores also in the inner of membrane as shown by scanning electron microscopy of cross-sections. The copolymer shows the characteristic units of acrylic acid and ethylene glycol as demonstrated by infrared spectroscopy. A minimum loss in carboxylic groups of acrylic acid during the plasma polymerization process was confirmed by X-ray photoelectron spectroscopy. Additional cell adhesion tests on copolymer coated polyethylene using IEC-6 cells demonstrated the bio-compatibility of the plasma-deposited hydrogel.
Copolymers of acrylic acid and styrene (AA/S) were prepared by pulsed plasma deposition technique. Their structure–property relationships were studied in dependence on the comonomer ratio. Both, the regularity of the structure and the composition of the thin copolymer films were investigated by bulk-sensitive (dielectric spectroscopy, FTIR, and differential scanning calorimetry) as well as surface-sensitive methods such as X-ray photoelectron spectroscopy (XPS). For an unambiguous identification of the functionality of the deposited films the COOH groups were estimated by derivatization with trifluoroethanol and subsequent XPS measurement as well as by the quantitative analysis of the FTIR data. As a result, the concentration of COOH groups on the surface and in the bulk is increasing with the fraction of AA in precursor mixture in a non-monotonous way but similar to the dependence obtained by conventional free radical polymerization.
The pulsed plasma polymerization of allyl alcohol was employed under the aspect of maximal retention of OH groups and the formation of a regular polymer structure. It should be noted that earlier investigations on plasma polymers deposited from allyl alcohol did not show extensive postplasma addition of oxygen and water vapor from ambient air during storage, measuring the elemental O/C ratio by means of X-ray photoelectron spectroscopy (XPS).The identification of OH groups in the plasma polymerized polymer using FTIR spectroscopy was such an indicator for fragmentation. The peak area of OH groups in the film which was stored was increased by about 20% compared to that measured ('in situ'). These phenomenons reflected that moisture and O2 in air played an important role in scavenging the free radicals. The addition of water and more specifically chemical bonding of OH of water in the deposited plasma polymer may serve as an indicator for monomer fragmentation, poly recombination, and the remaining radicals responsible for film formation. Moreover, the dielectric measurements show that the plasma deposited films are not thermally stable but undergo a postplasma chemical reaction during heating, where the reaction kinetics depends on pressure.