Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (36)
- Beitrag zu einem Tagungsband (20)
- Vortrag (18)
- Beitrag zu einem Sammelband (11)
- Buchkapitel (2)
- Posterpräsentation (1)
Sprache
- Englisch (88) (entfernen)
Schlagworte
- Creep (19)
- Nickel-base superalloys (12)
- Superalloy (8)
- Rafting (7)
- Low cycle fatigue (6)
- Single crystal (6)
- Superalloys (6)
- Constitutive law (5)
- Crack growth (5)
- Creep damage (5)
Organisationseinheit der BAM
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (18)
The shape of X-ray reflections from the cuboidal γ/γ'-microstructure was investigated. The measurements were performed on the 4th generation single-crystal nickel-base superalloy TMS138. It is shown that reflections from non-cubic crystallographic planes split not only in d-scale due to the different spacing of the γ- and γ'-lattices but also in the pole figure due to the tilting of γ-lattice planes. This tilting results from the elastic distortion of the γ-lattice caused by the γ/γ'-misfit. The results obtained are discussed under the methodical aspect of misfit measurement.
The calculation of the glide force on a dislocation in finite elasticity requires a suitable description of the variation of the deformation due to dislocation motion. This is achieved in this paper by extending the linear Somigliana-type dislocation model to finite strains. The core is modeled by a strip of finite width where the displacement jump continuously decreases with the distance to the dislocation tip. In the case of finite transformations, this distance can be defined in the deformed or in the undeformed state. By defining it in the undeformed natural state of the crystal, we show that the work dissipated by friction in the core region only depends on the dislocation motion. Using the principle of virtual work, the equation of the dislocation motion and several alternative expressions for the glide force are derived. The obtained force may be interpreted as a generalization of Eshelby's configurational forces for a noncoherent singular surface. In the linear case, the glide force of Peach and Koehler as well as the well-known expression of the self-force due to De Wit and Koehler are retrieved.
Results of an extended TMF test program on grade P92 steel in the temperature range of 620 °C - 300 °C, comprising in-phase (IP) and out-of-phase (OP) tests, partly performed with symmetric dwells at Tmax/Tmin, are presented. In contrast to previous studies, the low-strain regime is also illuminated, which approaches flexible operation in a power plant with start/stop cycles. At all strain amplitudes, the material performance is characterized by continuous cyclic softening, which is retarded in tests at lower strains but reaches similar magnitudes in the course of testing. In the investigated temperature range, the phase angle does not affect fatigue life in continuous experiments, whereas the IP condition is more detrimental in tests with dwells. Fractographic analyses indicate creep-dominated and fatigue-dominated damage for IP and OP, respectively. Analyses of the (micro)hardness distribution in the tested specimens suggest an enhanced microstructural softening in tests with dwell times for the low- but not for the high-strain regime. To rationalize the obtained fatigue data, the fracture-mechanics-based D_TMF concept, which was developed for TMF life assessment of ductile alloys, was applied. It is found that the D_TMF parameter correlates well with the measured fatigue lives, suggesting that subcritical growth of cracks (with sizes from a few microns to a few millimeters) governs failure in the investigated range of strain amplitudes.
A crystallographic constitutive model is developed, which accounts for both rate-sensitive and rate-insensitive flow. Single-crystal plasticity and viscoplasticity are the limiting cases of the model, so that it properly reflects the material response over a wide temperature range. A non-linear dynamic recovery is included to properly describe ratchetting. We provide a robust integration scheme based on generalization of the return-mapping algorithm and of the procedure for active set search.
The implicit integration and consistent tangent are implemented through the UMAT subroutine in the ABAQUS finite element program. The capability of the model to account for both high and low strain rates is demonstrated in numerical examples. Finally, the stability of integration scheme and quadratic convergence of the global NewtonRaphson equilibrium iterations are demonstrated on the example of a notched bar under tension.
Single crystal superalloys usually contain pores of sizes 5-10 micro-m after casting and heat treatment. These pores can be reduced under compression by combined creep and diffusion in a subsequent treatment called Hot Isostatic Pressing (HIP). The paper presents a methodology to simulate pore shrinkage under HIP conditions in two dimensions (2D).
At the scale of the pores, which is also the scale of the sub-grains (<50 micro-m) the dislocation sources cannot be assumed to be homogeneously distributed. Thus, the applicability of classical crystal plasticity is questionable. In this case, the transport of dislocations under an applied stress from the location where they are nucleated must be explicitly modelled. This is done by solving the transport equations for the dislocation densities and the elasticity equations in 2D. The dislocations are assumed to be nucleated at Low Angle Boundaries. They glide or climb through the sub-grains with a stress dependent velocity.
The transport equations are solved by the Flux-Corrected Transport method, which belongs to the predictor-corrector class of algorithms. In the first step, an artificial diffusion is introduced, which suppresses spurious oscillations of the solution. In a second step, the solution is corrected in such a way that no additional extremes appear and that the extremes do not grow. The algorithm is validated by simulating the transport of simple distributions with a constant velocity field.
With the dislocation velocities and the computed dislocation densities, the inelastic shear rate at the slip system level is computed by integrating the Orowan equation. In the 2D-setting, three slip systems are considered. The contributions of these slip systems are summed up to obtain the total inelastic strain rate. Dislocation glide and climb and the coupling of climb with vacancies diffusion are considered.
The resolution of the equilibrium equations from the inelastic strains turned out to be prone to numerical instabilities. As an alternative, the stresses are directly computed from the distribution of geometrically necessary dislocations following the method presented in. The resulting boundary value problem is solved by the Least-Square Finite Element method.
Examples of simulations are presented for a representative region under creep tension and for a pore shrinking under external pressure.
An extension of the constitutive viscoplastic model of Meric and Cailletaud is presented. The new model
accounts for coupling of plasticity and viscoplasticity to describe the rate dependence at low and moderate
temperatures. The model contains two boundaries: an elastic one and a viscoplastic one. Between the
boundaries, the only contribution to yielding is the rate dependent viscoplastic mechanism. Once the viscoplastic
boundary is reached, an additional rate independent flow mechanism becomes active. However, the extended
model is not able to predict properly both creep and long-term relaxation tests simultaneously. Therefore, a
deformation-induced softening is assumed, which is supposed to mainly affect static recovery.
The model has been calibrated with the mechanical tests on a single crystal nickel-basis superalloy. The uniaxial
tests have been carried out in the temperature interval 600°C – 1100°C in [001], [011] and [111] specimens.
The predicted creep, relaxation and non-isothermal cyclic tests exhibit reasonable agreement with the
experimental observations.
Gas turbines are widely used for a variety of purposes including power generation, compression or as jet engines in aircrafts. The critical components of a gas turbine are the high-pressure turbine blades which operate under severe conditions. These include thermo-mechanical loadings over temperatures ranging from room temperature up to 1100°C.
While a large number of constitutive models for single crystals have been proposed, most applications are restricted to special loading scenarios, temperature range and deformation mechanisms. In particular, a number of models are focused on pure creep. Only a few papers consider application of both creep and fatigue. Applications of the constitutive models to long-term stress relaxation are even scarcer. The new model assumes deformation-induced softening and can properly reproduce the viscous behavior at different time scales.
The model has been calibrated with the uniaxial tests at 800°C and 950°C in [001], [011] and [111] specimens of a nickel-basis superalloy. The predicted creep, short- and long-term relaxation and cyclic tests are in reasonable agreement with the experimental observations.
Single-crystal components made of nickel base superalloys contain pores after casting and homogenization heat treatment. Hot isostatic pressing (HIP), which is carried above the γ' -solvus temperature of the alloy, is industrially applied to reduce porosity. A modeling of HIP based on continuously distributed dislocations is developed in a 2D setting. Glide and climb of straight-edge dislocations, as well as vacancy diffusion, are the deformation mechanisms taken into account.
Thereby, dislocation glide is controlled by dragging a cloud of large atoms, and climb is controlled by vacancy diffusion. Relying on previous investigations of the creep behavior at HIP temperatures, it is assumed that new dislocations are nucleated at low-angle boundaries (LAB) and move through subgrains until they either reach the opposite LABs or react with other dislocations and annihilate.
Vacancies are created at the pore surface and diffuse through the alloy until they are either consumed by climbing dislocations or disappear at the LABs. The field equations are solved by finite elements. It is shown that pore shrinking is mostly controlled by vacancy diffusion as the shear stresses at the LABs are too low to
nucleate a sufficient amount of dislocations.
Simulation of fatigue crack growth by crack tip plastic blunting using cohesive zone elements
(2010)
The propagation of a fatigue crack in 2D specimens by crack tip plastic blunting is simulated by using a Finite Element implementation of the strip-yield model. At each cycle, the crack growth is assumed to result from the variation of the Crack Tip Opening Displacement (ΔCTOD). The implementation is based on cohesive elements with an elastic perfectly plastic behavior, which allows to simulate, the crack closure phenomena due to the plastic wake behind the crack tip. A mesh sensitivity analysis provides the minimum number of elements requested in the crack tip plastic zone for a given accuracy. Then, the advance scheme based on crack tip blunting is described. Finally, the variation of the opening load with respect to the load ratio R, and to the maximum load is investigated and compared with analytical results.
The stress States of components under Service conditions differ in general from the loading conditions that are routinely applied during material testing. When data that results, e.g., from uniaxial testing should be used for lifetime assessment, a good understanding of the failure behaviour in dependence of the stress state is necessary. For polycrystalline materials under high temperature loading, the development of creep damage is one important factor that limits a component’s lifetime. For cases where creep damage is related to the nucleation and growth of grain boundary cavities, the local normal stress acting on a grain boundary has been found to have a strong influence on the damage development. Hence, creep damage is usually localized along planes that lie perpendicular to the maximum principal tensile stress.