Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (25) (entfernen)
Referierte Publikation
- nein (25) (entfernen)
Schlagworte
- VOC (6)
- Emission test chamber (4)
- VOC emission (4)
- AgBB-Scheme (2)
- Chamber test (2)
- Construction product (2)
- Copiers (2)
- Dust (2)
- Emissionen (2)
- Emissions (2)
- Odour (2)
- Ozone (2)
- Printers (2)
- Tenax thermal desorption (2)
- Adsorptive wall material (1)
- Aerosol (1)
- AgBB-scheme (1)
- Aldehyde (1)
- Aldehydes (1)
- Antioxidant (1)
- Bauprodukte (1)
- Blue Angel (1)
- Building product (1)
- CO2 assisted impregnation (1)
- Cascade impactor (1)
- Cell (1)
- Certification/labelling (1)
- Chamber (1)
- Chamber copmparison (1)
- Construction and renovation (1)
- Construction products (1)
- Construction products directive (1)
- Cyclosiloxanes (1)
- Dämmstoffe (1)
- EN-Standards (1)
- Emission (1)
- Emission studies (1)
- Emissions testing (1)
- Environmental label (1)
- Fatty acid (1)
- Gas mixing device (1)
- Glas (1)
- Hardcopy device (1)
- Healthy homes and buildings (1)
- Hexanal (1)
- Indoor air (1)
- Indoor air quality (1)
- Insulation material (1)
- Interlaboratory study (1)
- Kammerverfahren (1)
- Laser printer (1)
- Medieval staind glass (1)
- OSB (1)
- Oriented strand boards (OSB) (1)
- Oxidation products (1)
- Plywood (1)
- Polymeric material (1)
- Proficiency testing (1)
- Quality assurance (1)
- Quality control (1)
- Round robin test (1)
- SVOC (1)
- Saturated and unsaturated aldehyde (1)
- Secondary emissions (1)
- Sorption flux (1)
- Sources/emissions (1)
- Terpenes (1)
- Test chambers (1)
- Thermal extraction (1)
- UFP (1)
- Ultra fine particle (1)
- VOC-Emission (1)
- VOCs (1)
- VOCs and SVOCs (1)
- Volatile Organic Compounds (1)
- Volatile organic compound (VOC) (1)
- Volatile organic compounds (1)
- Wood (1)
Organisationseinheit der BAM
Wood and wood products are often used as construction material for buildings and even more for furniture and indoor decoration. Therefore Chemical emissions from wood have an influence on the indoor air quality. A research project financed by the Federal Environmental Agency focused on VOC emissions from oriented Strand boards (OSB) and also from plywood made from pine and spruce (Wilke et al., 2011a). This paper shows results of the plywood testing because only little information is available about plywood emission behaviour and its impact on indoor air quality.
11 laser printers from 5 manufacturers were purchased in 2017 and tested for their UFP emissions. Size resolved sampling of the emitted particles was done with a 13 stage (30 nm to 10 µm) low pressure cascade impactor. The sampled particles were analysed for their chemical composition by thermal extraction (vaporization at 290°C) followed by GC-MS analysis. High boiling cyclic siloxanes (D10 to D16) were detected as constituents of UFP from laser printers. In comparison to measurements in 2008, aliphatic long-chain alkanes (C22 to C34) were detected additionally as chemical constituents of UFP from most of the tested printers and their amounts were higher than for cyclic siloxanes. Printers of one manufacturer showed very low UPF emissions compared to the other manufacturers.
Comparison of different types of emission test chambers and cells regarding VOC- and SVOC-emission
(2005)
VOC/SVOC-Emissions from materials for flooring installation (primer, screed, adhesive, floor covering) were measured by means of emission test chambers and cells over a time period of at least 28 days at 23 C, 50 % relative humidity and an area specific air flow rate of q = 1.25 m³/m²h. Single components were tested in comparison to three complete structures (same concrete, primer, screed, adhesive) with different types of floor covering (PVC, carpet, linoleum). Sorption into concrete/screed and different sealing by the flooring materials affected the emissions from the complete structures. The complete structures with linoleum and PVC showed the same emissions and emission rates as the flooring materials alone. Emissions from the carpet-covered structure resulted mainly from the lower layers. For two adhesives the formation of secondary emissions (aldehydes and organic acids) was observed starting after the standard testing time of 28 days.