Filtern
Dokumenttyp
Referierte Publikation
- nein (6)
Schlagworte
- Radioactive material (6) (entfernen)
Organisationseinheit der BAM
Internal cask content collisions during drop test of transport casks for radioactive materials
(2013)
In transport casks for radioactive materials, significantly large axial and radial gaps between cask and internal content are often present because of certain specific geometrical dimensions of the content (e.g. spent fuel elements) or thermal reasons. The possibility of inner relative movement between content and cask will increase if the content is not fixed. During drop testing, these movements can lead to internal cask content collisions, causing significantly high loads on the cask components and the content itself. Especially in vertical drop test orientations onto a lid side of the cask, an internal collision induced by a delayed impact of the content onto the inner side of the lid can cause high stress peaks in the lid and the lid bolts with the risk of component failure as well as impairment of the leak tightness of the closure system. This paper reflects causes and effects of the phenomenon of internal impact on the basis of experimental results obtained from instrumented drop tests with transport casks and on the basis of analytical approaches. Furthermore, the paper concludes the importance of consideration of possible cask content collisions in the safety analysis of transport casks for radioactive materials under accident conditions of transport.
The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of the sealing system of transport casks for spent fuel and high radioactive waste.
Applicants are requested by BAM to provide test programmes for verification of design leakage rates of the sealing system under the possible loads.
Two test series initiated to clarify the dependency of the standard leakage rate on dynamic lid displacement as well as the dependency of the useful elastic recovery ru of a metallic seal on temperature and time, are outlined in this paper as examples of present investigations:
Sliding tests simulating a lid displacement possible by a horizontal drop of the cask are carried out at the controlled drop test facility of BAM with test flange pairs equipped with metallic Helicoflex seals.
For specification of covering values for the useful elastic recovery ru GNS has started a very comprehensive test programme with overall 70 metallic seals installed in test flanges which are stored for a period of one year at three different temperatures up to 150°C.
This paper gives an overview about the current approach of BAM in the assessment of cask tightness and informs about the status of the running test series.
Type B(U) packages for the transport of radioactive material have to withstand accident conditions of transport defined in the regulations of the International Atomic Energy Agency in form of different mechanical (drop) tests with a subsequent thermal test. According to the regulatory requirements the orientation of the package in drop tests shall be such to cause the most damaged state in the components performing the safety functions.
For the package Iid system a 9 m drop onto the unyielding target with Iid side downwards is often the most damaging orientation. The impact Ioads acting on the Iid in this orientation result mainly from interaction between Iid and internal content. In case of a movable content its impact onto the inner side of the Iid can cause additional Ioad peaks on the Iid and the Iid bolts. The intensity of the internal collision depends on the position of content relating to Iid at the time of package first contact with target. Due to physical limitations an axial gap, which could be set in "pre-drop" configuration of package or which could spontaneously appear during the drop test, usually does not cover the maximum size possible in specific package design. In this context, the combination of drop tests with post-test analysis can be helpful to better estimate the effect of internal impact. The paper summarizes some aspects of this issue based on the BAM experience in the design assessment of Type B(U) transport packages. Additionally the paper shall support applicants in German approval procedures to reduce rounds of questions and ensure delivery of reliable safety case documents to the authorities.
Acceptable limits for activity release from transport casks for high-level radioactive material specified in the IAEA regulations must be kept by the integrity of cask body and the cask sealing system. BAM as the German competent authority for mechanical, thermal and containment assessment of packages liable for approval verifies the activity release compliance with the regulatory limits. One of the fundamental aspects in assessment is the specification of conservative package design leakage rates.
To ensure the required package tightness for both, storage, and transport of the cask before and after storage usually metal seals of the Helicoflex® Type are used. Due to the long-term use the seal behavior is influenced by temperature and time. The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport specified in the regulations can have a significant effect on the leak tightness of the sealing system. Whereas the safety for application of new, non- aged Helicoflex® seals is verified sufficiently, there are still technical data gaps concerning the efficiency of aged Helicoflex® seals.
BAM performed experiments to learn more about the sealing efficiency of aged Helicoflex® seals with Aluminum and Silver outer jackets. The seals were compressed in test-flanges and for artificial ageing the complete flange systems were stored in an oven for several month at a high temperature. During the compression and decompression tests after the aging, load-deformation characteristics of the seals, and leakage rates were measured. With these tests a load situation was simulated, which can occur in the regulatory drop test of the cask: Under high impact loads the bolted lid can lift a little for a short moment, allowing a little movement of the seal, so that the contact area can change before compressing again.
The poster presentation will show details about test conditions and first results.