Filtern
Erscheinungsjahr
- 2011 (312) (entfernen)
Dokumenttyp
- Beitrag zu einem Tagungsband (312) (entfernen)
Sprache
- Englisch (177)
- Deutsch (133)
- Mehrsprachig (1)
- Russisch (1)
Referierte Publikation
- nein (312) (entfernen)
Schlagworte
- Recycling (8)
- Sekundärrohstoffe (7)
- Beton (6)
- Concrete (6)
- Leichtbeton (6)
- Schallemissionsprüfung (6)
- Sekundäre Gesteinskörnung (6)
- Computed tomography (5)
- Korrosion (5)
- Ultraschall (5)
Mineralische Sekundärrohstoffe finden im Beton als Gesteinskörnung, Betonzusatzstoff, Bestandteil von Zementen oder Spezialbindemitteln Anwendung. Für den Einsatz von rezyklierten Gesteinskörnungen, Kesselsand, Steinkohlenflugasche, Silicastaub und Hüttensand bestehen bereits Normen bzw. bauaufsichtliche Zulassungen. Für weitere Reststoffe, wie Mauerwerkbruch und beim Baustoffrecycling anfallende feinkörnige, heterogene Sandfraktionen, existieren noch keine höherwertigen Verwertungswege. In einem Forschungsprojekt werden derzeit Möglichkeiten zur Verwertung von heterogenen mineralischen Bau- und Abbruchabfällen durch Herstellung von Blähgranulaten mit maßgeschneiderten Eigenschaften (Schüttdichte, Rohdichte, Korngröße und Kornfestigkeit) untersucht. Dies eröffnet die Möglichkeit einer rohstofflichen Verwertung solcher Abfälle. Im Mittelpunkt der Untersuchungen steht der Mauerwerkbruch. Er fällt mit über 20 Tonnen pro Jahr an und weist im Vergleich zum Betonbruch größere Verwertungsdefizite auf hl. Die erzeugten Granulate sollen als leichte Gesteinskörnung im Beton, Schüttung oder Pflanzsubstrat Anwendung finden.
Die ersten Ergebnisse der Granulatherstellung mit einer thermischen Behandlung zeigen, dass sich Mauerwerkbruch als Rohstoff zur Herstellung leichter Gesteinskörnungen eignet 121. Die so erzeugten Blähgranulate weisen ähnliche Eigenschaften wie herkömmliche Blähtöne auf 131. Das Hauptziel der in diesem Beitrag vorgestellten weiteren Untersuchungen war, die Rohdichte der Granulate bei gleichbleibender oder steigender Kornfestigkeit zu senken. Aus energetischer Sicht des Blähprozesses wurde neben dem thermischen Verfahren auch die Möglichkeit einer hydrothermalen Erhärtung der Granulate untersucht.
The paper presents numerical methods to detect and classify defects and inhomogeneities by means of active thermography. The objective is to determine the wall thickness of structure elements with an inaccessible back wall, for example, of pipes or Containers. As test specimens we used approximately 2 cm thick PVC samples with spatial variations in the back wall geometry. Flash lamps provided the heating. To know the thickness of the wall, we used two inversion methods and compared the results achieved. One is an iterative echo defect shape method and already tested on Steel test specimens with good reconstruction results. The second one is the Levenberg-Marquardt method, applied here to thermographic data for non-destructive testing. Since data capturing using active thermography and the presented numerical methods can easily be automated, the combination of these two procedures is a promising approach providing a broad area of application.
Reinforced concrete piles are used in case of structures that are constructed on soft ground to transfer the loads into deeper strata with sufficient bearing capacity. In order to determine the pile’s behavior and possible damage, static and dynamic pile tests are carried out. Dynamic measurements taken from the pile head can show the bearing behavior and structural integrity by using the theory of wave propagation. In order to receive more precise information about the pile features, now, a string of sensors is embedded at different levels of the pile. A fiber optic strain wave sensor, based on the extrinsic Fabry-Perot interferometer (EFPI), has already been developed and tested in full-scale field tests by Schallert (2010). It was possible to detect the introduced deformation caused by the static load and the dilatational wave during dynamic loading. Although the full-scale tests were successful, the engineering design of the sensor body left room - from the economical point of view - to be optimized. After laboratory tests with the optimized sensor, a cast-in-situ bored pile has been built at the BAM Test Site Technical Safety in Horstwalde, South of Berlin. Additionally to the EFPI sensors, fiber Bragg grating (FBG) sensors, temperature sensors and resistance strain gauge (RSG) sensors are embedded in order to compare the signals with each other. In this paper, the modified sensor and the Setup of the cast-in-situ bored pile along with results of dynamic tests are shown.
Ein stereo-fotogrammetrisches Messverfahren wurde zur quantitativen Analyse der Bewegungssignale eines elektrischen Multi-Sensorsystems eingesetzt. Der Vergleich von Weg- und Winkel-Zeitverläufen zeigte bereits eine recht gute Übereinstimmung, verdeutlichte jedoch auch die Notwendigkeit einer weiterzuentwickelnden Kalibriermethodik. Die Stereo-Videogrammetrie hat sich als Referenzverfahren zur Analyse und Validierung dreidimensional ausgelegter elektrischer Bewegungssensorik für den Nahbereich bewährt.
Beton mit leichten Gesteinskörnungen (Leichtzuschlägen) ist seit dem Altertum bekannt. Leichte Gesteinskörnungen vulkanischen Ursprungs wurden bereits zur Errichtung der Maya-Pyramiden in Mexiko und von monumentalen Bauwerken im Römischen Reich verwendet. Zu den berühmtesten Beispielen der ersten Anwendung von Leichtbeton in Europa gehören das Kolosseum und das Pantheon in Rom, Hier wurden sowohl natürliche als auch künstliche Zuschlagstoffe, wie Bims, Lava und zerkleinerter Ziegelsplitt, benutzt.
Mit steigender Nachfrage nach leichten Gesteinskörnungen und einer weltweit begrenzten Verfügbarkeit natürlicher Leichtzuschläge wurden synthetische leichte Gesteinskörnungen entwickelt. Ihre großtechnische Herstellung begann nach dem Ersten Weltkrieg. Heute werden leichte Gesteinskörnungen in einem breiten Schüttdichtespektrum von 100 bis 1200 kg/m3 hergestellt. Sie stellen einen wichtigen Teil der Gesteinskörnungen in der Baubranche dar.
Structural health monitoring of wind turbine blades by strain measurement and vibration analysis
(2011)
Wind turbine blades have to withstand a high number of load cycles in mostly hard weather conditions over 20 years. In a research project BAM and several partners have designed, evaluated and tested a condition monitoring system for all parts of a wind turbine. At a rotorblade with a length of 58 m fibre bragg grating sensors were applied for in-service strain measurement. Additionally a complex test rig was designed to enable real biaxial loading conditions at a representative test rotor blade to simulate the mechanical loading conditions in the lab. In this test blade with a length of 8 m also fibre bragg grating sensors were implemented to determine their influences for the structure and the condition monitoring system. Vibration measurements were carried out at different test phases. The results were compared with finite element strain and modal analysis.
Integration of magnetic functional components in LTCC Circuit boards calls for co-firing of dielectric and ferrite tapes. Ni-Cu-Zn ferrites with permeability of p=900 were developed which can be fully densified at the Standard LTCC sintering temperature of 900 °C. Successful co-firing of this ferrite with dielectric tapes requires the adaptation of the shrinkage behavior of the materials as well as the thermal expansion during the cooling period - especially in the temperature range below the transformation point of the glassy phase of the dielectric tape. To match these preconditions, a new dielectric LTCC material with steep sintering curve and high thermal expansion coefficient was designed. Sintered multilayer composed of Ni-Cu-Zn ferrite and tailored dielectric tapes are free of cracks and possess no open porosity. No significant interdiffusion between the ferrite and dielectric tapes was found by EDX measurements. Compared to pure ferrite laminates the permeability of co-sintered Ni-Cu-Zn ferrite layers is drastically reduced to 400, i.e. a decrease of more than 50 %.
To investigate the origin of this permeability reduction, Ni-Cu-Zn ferrite laminates were sintered separately, and in combination with alumina release tapes or dielectric tapes, respectively. SEM and EDX analysis of co-fired laminates reveal differences in the ferrite grain growth behavior. Ferrite laminates with homogeneous microstructure and grain size up to 50 pm exhibit large permeability. However, growth of ferrite grains does not take place near the interface between ferrite and release or dielectric tapes. There is a strong correlation between high permeability and volume fraction of large ferrite grains. Regions of fine and coarse grains inside the ferrite layers show different bismuth concentration; the Bi-content is larger in regions of fine ferrite grains.
Die Streuung der Agt-Werte von Betonstahl bleibt durch die Variation der Prüfbedingungen (Temperatur, Geschwindigkeit) innerhalb der prüfnormseitig zulässigen Grenzen weitgehend unbeeinflusst. Gleichzeitig führt die Variation der Prüfbedingungen zu einer signifikanten, für die Produktabnahme relevanten Änderung des Niveaus von Agt. Die Auswertemethodik des Zugversuches (Festlegung der Höchstkraft, Wahl des Verfahrens zur Agt-Bestimmung) hat einen signifikanten Einfluss auf Niveau und Streuung von Agt. Es werden Empfehlungen zur Minimierung der Streuung von Agt gegeben.
Fatigue testing in the VHCF ränge requires testing machines with increased frequencies. However, application of energy-saving resonance testing leads to a linkage between test frequency and specimen Parameters. The frequency ränge and the available forces of the testing machine are limiting possible specimen dimensions.
Electrodynamic shakers combine test frequencies up to 4000 Hz with forces in the kN range. Thus, a relatively wide range of tests is possible which allows studying the influence of specimen size on VHCF behaviour.
Electrodynamic shakers as well as the respective Computer control Systems and Vibration measurement techniques are well established in scientific and technical applications. We present results of a first study of VHCF testing on electrodynamic shakers conducted at BAM. Test frequency, specimen size and stress levels have been varied. One goal is to balance the needs of materials testing with the Standard test Systems of environmental Simulation to provide a powerful and flexible tool for very high cycle fatigue testing. Further investigation to optimize the technique is required.
Der Begriff „Materialfehler“ wird nicht nur im Bereich der Schadensanalyse von Laien, Juristen und Ingenieuren sondern auch in der Öffentlichkeit sehr häufig verwendet, leider mit den verschiedensten Bedeutungen. Dies führt immer wieder zu Missverständnissen. Ziel der hier vorgestellten BAM-Untersuchung und Recherche war zu klären, ob und ggf. wo es Definitionen für den „Materialfehler“ gibt, wie der Begriff in den oben angesprochenen Bereichen verwendet wird. Weiterhin wurde untersucht, ob diese Verwendungen / Definitionen in die in der Schadensanalyse definierte Begriffswelt passen bzw. welche Definition ergänzt werden sollte. Im Gegensatz zu „Material“, „Werkstoff1 oder „Werkstofffehler“ ist der häufig verwendete Begriff „Materialfehler“ erstaunlicherweise bisher nicht definiert!
Um den oft verwendeten Begriff des Materialfehlers für die Schadensanalyse und die damit befassten Bereiche einheitlich zu beschreiben, wird folgende Definition vorgeschlagen:
„Materialfehler" sind Werkstoff- und/oder Fertigungsfehler. Darin sind alle Fehler (Abweichungen von Spezifikationen/Normen) im Werkstoff bzw. dessen Herstellung/Fertigung enthalten.
Demgegenüber sind Konstruktions-/Planungsfehler oder Betriebsfehler keine Materialfehler.
In the approval procedure of transport packages for radioactive materials, the mechanical and thermal safety assessment is carried out in Germany by competent authority BAM. In recent years BAM was involved in several licensing procedures of new spent fuel and HLW package designs, where the cask body was made of Ductile Cast Iron (DCI). According to IAEA regulations package designs have to fulfill requirements for specific conditions of transport. Type B(U) packages must withstand the defined accident conditions of transport. The temperature range from -40°C up to the operational temperature has to be considered. For the cask material DCI, it is necessary to determine the brittle fracture behavior. The German guideline BAM-GGR 007 defines requirements for the fracture mechanics of DCI. Due to complex structure of the cask body and the dynamic loading a fracture mechanical assessment in an analytical kind is not always possible. Experience of recent design approval procedures show that the application of numerical calculations are applicable to determine the fracture mechanical load in the cask body. At the first step a numerical analysis has to be done to identify the loading state at the whole cask body. Secondly an analysis of a detail of the cask body is made considering the displacement boundary conditions of the global model. An artificial flaw is considered in this detailed model to calculate the fracture mechanical loading state. The finite element mesh was strongly refined in the area of flaw. The size of the artificial flaw is characterized by the ultrasonic inspection used for the quality assurance of the package. The applicant developed additional analysis tools for calculation of stress intensity factor and/or J-Integral. The assessment approach by BAM led to the decision to develop own tools to the possibility for independent check of the results.
The paper describes the authority assessment approach for the DCI fracture mechanics analysis. The validation procedure incl. the development of own tools is explained. BAM developed a post-processor called JINFEM to determine the fracture mechanical loads. The regulatory 1 m puncture bar drop test is used to give an example of the assessment procedure.
Further miniaturization of electronic packaging calls for integration of magnetic functional components into LTCC modules. For integration of magnetic function into LTCC, low fired MnZn- and NiCuZn-ferrites which can be fully densified at the standard LTCC sintering temperature of 900°C were developed. To co-fire these ferrite tapes with dielectric tapes the sintering shrinkage and the coefficient of thermal expansion of ferrite and dielectric tapes must be matched. For each ferrite material a new LTCC dielectric material was designed. The embedded ferrite tapes into new LTCC dielectric tapes can be sufficiently densified during co-firing at 900°C without any cracking. Compared to separately sintered ferrites the permeability of embedded ferrite tapes is reduced. For embedded NiCuZn ferrites permeabilities between 230 and 570 (at 2 MHz) according to the thickness of the embedded ferrite layer were measured. For embedded MnZn ferrites a permeability of 300 was measured.
Die Qualität von rezyklierten Gesteinskörnungen muss nicht nur bautechnischen Anforderungen und rechtlich verbindlichen Umweltstandards genügen, sondern ihr Einsatz in der Betonherstellung wird auch vor dem Hintergrund der Leitlinien der Nachhaltigkeit bewertet. Für die Gewinnung von rezyklierten Gesteinskörnungen bedeutet dies, dass sowohl bei den Abbrucharbeiten als auch bei der Bauschuttaufbereitung darauf geachtet werden muss, dass die gewählten Verfahren nicht nur ökonomischen Kriterien genügen müssen, sondern auch keine nachteiligen ökologischen oder sozialen Auswirkungen haben dürfen.
In verschiedenen Forschungsprojekten konnte durch ökobilanzielle Bewertungen von einzelnen Verfahren und Verfahrensabläufen gezeigt werden, dass rezyklierte Gesteinskörnungen aus Altbeton unter bestimmten Rahmenbedingungen umweltverträglich gewonnen werden können und ihre Nutzung durch die Substitution von Natursteinkörnungen sowohl zur Schonung von natürlichen Ressourcen als auch zu einer Reduzierung von Umweltbelastungen beitragen kann.
Die im Mai 2011 veröffentlichte Internationale Norm ISO 6892-2 "Metallische Werkstoffe — Zugversuch - Teil 2: Prüfverfahren bei erhöhter Temperatur" ersetzt die Europäische Norm EN 10002-5 und die Internationale Norm ISO 783.
Technische Änderungen/Ergänzungen im Vergleich zu den Vorgängernormen beziehen sich im Wesentlichen auf die Prüfgeschwindigkeiten und die Dehnungsmessung. In Anlehnung an Teil 1 der ISO 6892 (Prüfung bei Raumtemperatur) wird die Dehngeschwindigkeit als maßgebliche Prüfgeschwindigkeit mit eingeengten Bereichen (Verfahren A) empfohlen. Zum Ansetzen des Dehnungsaufnehmers und zur Festlegung der Messlänge sind nun verschiedene Verfahren möglich.
In dem Beitrag wird auch anhand von Beispielen auf mögliche Auswirkungen auf die zu bestimmenden Kennwerte eingegangen.
Ein wesentlicher Vorteil der Dünnschichtphotovoltaik gegenüber der waferbasierten Photovoltaik liegt in der monolithischen Serienverschaltung. Bei der Herstellung von Chalkopyrit(CIGSe) -Dünnschicht-Solarmodulen erfolgen dafür typischerweise ein Laser-Strukturierungsschritt (P1) und zwei mechanische Strukturierungsschritte (P2, P3). In diesem Beitrag wird gezeigt, dass die Strukturierung von CIGSe-Solarmodulen vollständig mit kurzen Laserpulsen (<10 ns Pulsdauer) und einer einzigen Wellenlänge (532 nm) möglich ist. Der P1- und P3-Schnitt erfolgen durch direkte induzierte Ablation. Für den P2-Schnitt wird gezielt der hohe Wärmeeintrag der ns-Laserpulse genutzt, um die CIGSe-
Absorberschicht lokal aufzuschmelzen und strukturell so zu verändern, dass eine elektrisch gut leitende Verbindung zwischen Front- und Rückkontakt entsteht.
Manufacturing of CIGSe thin film solar modules involves typically one laser structuring step (P1) and two mechanical structuring steps (P2 and P3) for serial interconnection. In our approach, complete laser structuring is successfully demonstrated by application of short nanosecond laser pulses (<10 ns) with a single, visible wavelength of 532 nm. The P1 and the P3 trenches are scribed by induced and direct ablation, respectively. For the P2 scribe, the thermal input of the ns laser pulses is used to transform the CIGSe absorber layer locally into a highly conductive compound to provide proper electrical interconnection. These findings promise further simplification and flexibility to thin film solar cell production.
Structuring of thin-film photovoltaic modules requires basic knowledge of the laser – thin-film interaction in order to adapt the accessible laser parameters, like wavelength, power, repetition rate and scribing speed whilst taking into account the specific material properties of the layer. We have studied the nanosecond laserablation behavior of corresponding layers (i) of silicon based thin-film solar cells with a-Si/µc-Si tandem absorber type and (ii) of back contact and absorber layer of CIGSe solar cells. The respective ablation threshold fluences were determined as integrative parameters describing the specific laser – material interaction. For the threshold determination we used two different methods and developed a new analytical approach taking into account scribing through the glass substrate as it is preferred for most structuring processes. This was done by analyzing the thin film ablation results by means of optical microscopy, profilometry, scanning electron microscopy (SEM). Moreover, we determined the incubation coefficient of the regarded material layers which allows us to predict quantitatively the influence of the spot overlap on the scribing threshold.
Towards an industrial laser doping process for the selective emitter using phosphoric acid as dopant
(2011)
Different laser supported approaches have already been realized, proving the great potential of laserdoped selective emitters (LDSE). However, it is challenging to establish a low-cost process by using pulsed laser tools. So far a single-step process only leads to satisfying results utilizing cw-lasers. In this paper we have examined a two-step process to produce laser-doped selective emitters on multicrystalline textured standard silicon photovoltaic wafers (90-Ω/sq-Emitter, SiN-antireflection coating (ARC)). The precise ARC removal by near-infrared fs-laser pulses (30 fs, 800 nm), and the doping of uncoated silicon wafers by ns-laser pulses (8 ns, 532 nm) were systematically investigated. In the fs-experiment, optimum conditions for ARC removal were identified. In the nsexperiments under suitable conditions (melting regime), the phosphorous concentration underneath the wafer surface was significantly increased and the sheet resistance was reduced by nearly a factor of two. Moreover, electrical measurements on fired metallization fingers deposited on the laser processed wafers showed low contact resistances. Hence, wafer conditioning with combined fs-laser- and ns-laser-processes are expected to be a promising technology for producing selective emitters.
The selective emitter is a well-known technology for producing highly doped areas under the metallization grid to improve the solar cell performance. In this work, the influence of laser irradiation on phosphoric acid coated multicrystalline silicon PV-wafers on the wafer surface structure, the phosphorous depth distribution and the electrical contact resistance within the laser treated area as well as the electrical series resistance of laserprocessed solar cells was evaluated. Different laser processing settings were tested including pulsed and continuous wave (cw) laser sources (515 nm, 532 nm, 1064 nm wavelength). Complementary numerical simulations using the finite element method (FEM) were conducted to explain the impact of the laser parameters on the melting behavior (melt duration and geometry). It was found that the melt duration is a key parameter for a successful laser Doping process. Our simulations at a laser wavelengths of 515 nm reveal that low-repetition rate (<500 kHz) laser pulses of 300 ns duration generate a melt duration of ~0.35 µs, whereas upon scanning cw-laser radiation at 532 nm prolongates the melt duration by at least one order of magnitude. Experimentally, the widely used ns-laser pulses did not lead to satisfying laser irradiation results. In contrast, cw-laser radiation and scan velocities of less than 2 m/s led to suitable laser doping featuring low electrical resistances in the laser treated areas.
Die lokalen Festigkeiten im Bereich einer Schweißverbindung sind maßgebend für deren Widerstandsfähigkeit gegenüber mechanischen Beanspruchungen. Im Gegensatz zu anderen präparationsaufwendigen Methoden, z. B. die Untersuchung von Mikro-Zugproben, liefert die instrumentierte Eindringprüfung mit deutlich geringerem Aufwand Verläufe von Festigkeiten mit sehr guter Ortsauflösung. Es werden wahre Spannungs-Dehnungs-Kurven aus zyklischen Eindringversuchen mittels Auswertungen auf der Basis repräsentativer Spannungen und Dehnungen und auf der Basis neuronaler Netze an Punktschweißverbindungen zweier hochfester Stähle, eines TRIP-Stahls und eines martensitischen Stahls, sowie eines weichen niedrig legierten Stahls bestimmt, jeweils im Bereich des Grundwerkstoffs und der Schweißlinse.
Use of higher-alloyed metallic materials and duplex steels for transport tanks of dangerous goods
(2011)
Compatibility evaluations of selected metallic materials under the influence of dangerous goods are published in the BAM-List - Requirements for Tanks for the Transport of Dangerous Goods” as basis for substance-related prototype approvals for tank Containers designed for the carriage of dangerous goods.
There is a request of the tank manufacturing industry and transportation Companies to incorporate additional materials into the BAM-List, especially corrosion-resistant materials because of the large number of corrosive dangerous goods. One solution to solve corrosion Problems is to line the tank with a polymer, an alternative solution is the application of high-alloyed stainless steels and nickel-based alloys as there are 1.4529 (XINiCrMoCu 25-20-7, alloy 926), 1.4562 (X1NiCrMoCu32-28-7, alloy 31) and 2.4605 (NiCr23Mo16AI, alloy 59).
There is an interest to use cost-efficient steels with high strength values and concomitant adequate corrosion resistance such as duplex steel 1.4362 (X2CrNiN23-4).
This steel grade was originally developed as a substitute for the austenitic grades 1.4404 (X2CrNiMo17-12-2) and 1.4571 (X6CrNiMoTi17-12-2). Due to the lower content of the alloy elements nickel and molybdenum this duplex steel is a cost-efficient alternative to molybdenum containing austenite.
Due to the limited number of corrosion test results with welded test samples of these high-alloyed materials and the duplex steel under the influence of corrosive dangerous goods a comprehensive test Programme was performed with these materials in Cooperation with ThyssenKrupp VDM and Deutsche Edelstahlwerke GmbH. It can be concluded from the test results that the superaustenitic steels 1.4529 and 1.4562 as well as the nickel-based alloy 2.4605 are a really good alternative as tank materials for the transport of dangerous goods in comparison to the lining of the tanks. The nickel-based alloy 2.4605 shows the best resistance and is suitable as material for tanks transporting all tested corrosive substances. One exception is the temperature limit during the transport of hydrochloric acid.
The superaustenit 1.4562 is a resistant material with a wide ränge of application. Exceptions for use are: ammonium bifluoride, brine, 34 % calcium Chloride solution, hydrochloric acid, perchloric acid, 90 % 2-chloropropionic acid, nitrating acid with nitric acid content > 50 % and molten monochloroacetic acid. The alloy is limited suitable for allyl Chloride, aluminum Chloride, copper (II) -Chloride and ferric Chloride. The superaustenit 1.4529 showed the lowest resistance compared to the other two materials. This steel is not resistant in hydrochloric acid, perchloric acid, sodium Chlorite and sodium hypochlorite. The application is limited in the concentration ränge of aqueous Solutions of aluminum Chloride, copper (II) Chloride and ferric Chloride. Due to the reduced alloying content of the duplex steel 1.4362 (X2CrNiN23-4) compared to the austenitic CrNiMo-steels, a lower resistance especially in acidic media like formic, acetic or sulfuric acid was observed. Within the more than 7.000 substances contained in the BAM-List there is a large amount of dangerous goods such as hydrocarbons, alcohols, aldehydes, ketones, ethers, esters, and inorganic alkaline substances which have a large transport volume and do not corrode the duplex steel 1.4362 (X2CrNiN23-4).
The test results are included in the actual 11th edition of the BAM-List and therefore available for the costumer.
Rubbers are often used for seal applications due to their special material properties and easy use. In many applications the material is exposed to low temperatures during Operation. Therefore it is important to know the material behavior at low temperatures to determine the temperature ränge that allows a Safe Operation of the seal, e.g. in storage and transport Containers for radioactive materials.
The seal function of an elastomer is limited in temperature by the rubber-glass transition during which the material properties change from rubber-like to stiff and glass-like. For a given application this correlation is not trivial and therefore needs an in-depth investigation under consideration of the physical properties and the
application conditions.
In this work different analytical methods are used to characterize the material behavior at low temperature in the ränge of the glass-rubber-transition and are compared with the quality of Operation of a component which is here defined by the detected leakage rate.
We present the status of our work on a tube shaped 3D deformation sensor based on continuously distributed fiber optic sensing. A sensor tube of very large diameter is used to ensure high sensitivity while the transportability and applicability are still comfortable due to our application strategy. The setup is designed to use different measurement techniques in the applied optical fibers including Brillouin based measurements and interferometric optical frequency domain measurements using an OBR 4400 from Luna Technologies.
Zur Abschätzung der Lebensdauer eines bei höherer Temperatur langzeitbelasteten Bauteils wurden Zeitstandversuche, Relaxationsversuche und weitere Versuche mit unterschiedlichen Umgebungssteifigkeiten durchgeführt.
Die Zeitstandversuche, deren Versuchsführung eine unendlich niedrige Umgebungssteifigkeit simuliert, liefern geringere Lebensdauern (Bruchzeiten) im Vergleich zu Versuchen mit endlich hohen, technisch relevanten Steifigkeiten bei vergleichbarer Probensteifigkeit (Geometrie), wobei die Lebensdauern mit steigender Umgebungssteifigkeit zunehmen. Die längsten Lebensdauern zeigen Relaxationsversuche mit einer unendlich hohen Umgebungssteifigkeit aufgrund ihrer Versuchsregelung.
Für die Übertragung der an Proben gewonnenen Ergebnisse auf das Bauteil wurde das Steifigkeitsverhältnis Z zwischen der Steifigkeit der 'Probe' und der der 'Umgebung' definiert und angewandt. Das Steifigkeitsverhältnis des kritischen Bereichs im Bauteil und das der Werkstoffprobe in der Prüfmaschine sollten möglichst ähnlich sein. Dann lassen sich bei der Übertragung auf das Bauteil realistisch höhere Lebensdauern abschätzen als nur mit Kenntnis der Ergebnisse der Zeit-standversuche.
Die Restlebensdauerabschätzung von Faserkunststoffverbunden ist ein ungelöstes
Problem. Die Beobachtung der Matrixschädigung ist dabei ein vielversprechender Ansatz zur Bewertung des Schädigungszustandes insgesamt. Unter kombinierter Beobachtung mit Röntgenrefraktionsmessungen und Schallemissionsmessung wurden uni- und biaxiale Lasten statisch und zyklisch auf Kohlenstofffaserepoxidharz-Proben aufgebracht. Die uniaxiale Belastung erfolgt mittels einer eigenentwickelten Kompaktprüfmaschine direkt während der Röntgenrefraktions- und Schallemissionsmessung in der Röntgenkammer. Die biaxiale Belastung wird an Modelldruckbehältern ebenfalls mit Schallemissionsmessung durchgeführt. Hier wird der Modelldruckbehälter mit dem Röntgenrefraktionsverfahren periodisch inspiziert.
Structural performances of earthen building materials. A comparison between different typologies
(2011)
Traditional construction techniques utilizing earthen materials are often seen as inferior compared to modern ways of building. Structural earthen elements are perceived as vulnerable towards environmental influences (moisture, frost) and in particular towards the load scenarios during earthquakes. In comparison to the recent advances in research on stone and brick masonry, knowledge on the structural performance of earthen building construction is limited and scattered. Consequently the confidence in the performance of these earthen buildings constructed in the traditional techniques during earthquakes is fairly low. The research presented here aims to make a comparison of mechanical behavior between different earth masonry material typologies, consisting of earth block masonry, rammed earth and cob. The paper has been developed in the framework of a larger research program called NIKER. BAM and other seventeen research partners from the Mediterrean area are jointly involved to develop and validate innovative materials and technologies for the systemic improvement of the seismic behavior of Cultural Heritage assets
Experimental investigation of the laser-plume interaction during high power fiber laser welding
(2011)
The effect of the well-known plasma absorption and refraction in CO2-laser metal welding plumes is in case of high power solid state laser welding negligibly small. By contrast, the diffraction effects of shorter wavelength laser radiation are considerable. According
to the results of preliminary studies, the fine condensed metal particles in the welding plume can lead to essential worsening of the laser beam quality.
This work is devoted to the investigation of the lasermatter interaction during up to 20 kW ytterbium fiber laser welding of thick mild steel plates. The plume attenuation of a probe 1.3 µm wavelength diode laser beam as well as of continuous radiation in 250-600 nm
wavelength range was measured during welding with and without Ar shielding gas supply. The measured results allow it to calculate average size and concentration of fine condensed metal particles in
different plume areas using the multi-wavelength method and the Mie scattering theory. The plume temperature, which determines the condensation conditions, was measured by means of Fe I atom
spectral line emission registration.
The obtained results can be also of interest for remote metal treatment with high-power fiber or disc lasers.
In connection with the use of chemically unstable gases (especially acetylene and ethylene oxide) accidents keep on happening - amongst them also quite serious ones. These gases are known to be chemically unstable. A chemically unstable sas is a flammable gas that is able to react exolosivelv even in the absence of air or oxveen. The investigation of accidents showed that the Chemical instability of flammable gases played an important role in the severity of accidents. Therefore, this hazardous property was included in the global harmonizatiön of the Classification of Chemicals. The Classification of chemically unstable flammable gases and mixtures is an amendment to Chapter 2.2 “Flammable gases” of the UN Globally Harmonized System of Classification and Labelling of Chemicals (GHS), because most chemically unstable gases are flammable as well. The proposal to add them to the GHS originated from the experts of an informal working group of the UN Sub-Committee of Expert on the GHS (UNSCEGHS) headed by BAM, Germany. The UNSCEGHS has decided to include it in the Fourth Revised Edition of the GHS. The respective method for determining whether a gas is chemically unstable or not, is included in the UN Manual of Tests and Criteria. This paper presents some experimental investigations of these gases, the test methods, examples of new classifications and results from CHEMSAFE
Faserverbundbauteile werden durch Tränkung von Fasergewebe mit flüssigem Harz, in der Regel Epoxidharzen, und anschließender Härtung des Harzes gefertigt. Dabei kann man das Gewebe im Vorfeld mit reaktivem Harz tränken und als so genanntes Prepreg verarbeiten oder man injiziert das frisch mit dem Härter gemischte Harz in ein Werkzeug, in dem das Gewebe bereits liegt - z. B. beim RTM-Prozess. Ausgehend von der Aufgabenstellung, eine Prepregherstellung mit hohem Qualitätsstandard zu realisieren und Möglichkeiten der Fertigungskontrolle für den Prepreg-Verarbeiter aufzuzeigen, wurde an einem für die Prepregherstellung vorgesehenen Harzsystem eine weitgehende Charakterisierung des Aushärtungsverlaufs vorgenommen. Wegen der Schwierigkeit, schnell konstante Aushärtungstemperaturen zu erreichen, wurden bei allen Methoden mit einer Heizrate von 1 K/min von RT bis 200 °C aufgeheizt.
Cementitious materials, in particular concrete, are durable materials if prepared appropriately and the Service life of concrete structures is now often required to last 120 years or more. Concrete durability depends strongly on intrinsic (e.g. composition, porosity) and exterior factors (e.g. moisture condition and composition, frost cycles, load pattem). Deleterious actions leading to concrete degradation are often created by the environment. Extemal sulfate attack is one of the more spectacular damage scenarios for concrete structures caused by the ingress of sulfate ions into the pore System of the material and successive formation of expanding phases. Though in recent years well studied there are still many questions remaining conceming the mechanisms of sulfate attack. In particular over the last ten years, with the increased utilization of blended cements, new questions arose concerning the sulfate resistance of those binder Systems. In the presented study therefore a method was developed to analyze the changes of the phase composition within the micro structure due to sulfate attack. The analytical method was based on pX-Ray diffraction (pXRD) using Synchrotron radiation in Debye-Scherrer (transmission) geometry. The spatial resolution of the method is ca. 10 pm and allows the characterization of phase transformations in the wake of damaging processes in more detail compared to other techniques. Furthermore, the experimental setup provides the possibility for analyzing the phase assemblage of a given sample without destroying the micro structure. This is possible because the specimens for phase analysis consists of thick sections, which can be used for further microscopic analysis of the micro structure and micro chemistry (e.g. by SEM-EDX). Samples containing supplementary cementitious materials were measured in comparison and to reconstruct the influence of the degradation process in detail. Additionally, reaction ffonts within the samples were localized by micro x-ray fluorescence analysis (MXRF).
A three-dimensional laminar steady
state numerical model was used to investigate
the influence of an alternating current (ac)
magnetic field during high power laser beam
keyhole welding of 20 mm thick nonferromagnetic
aluminum. COMSOL
Multiphysics was used to calculate the threedimensional
heat transfer, fluid dynamics and
electromagnetic field equations. Most
important physical effects of the process were
taken into account: Thermo-capillary
(Marangoni) convection at the upper and lower
weld pool boundaries, natural convection due
to gravity and latent heat of solid-liquid phase
transition. It is shown that the gravity drop-out
associated with welding of thick plates due to
the hydrostatic pressure can be prevented by
the application of an ac magnetic field. The
application of an oscillating magnetic field of
70 mT was investigated to allow for singlepass
laser beam welding of thick aluminum
plates. The flow pattern in the molten zone and
the temperature distributions are significantly
changed.
The inelastic torsional response of an asymmetric-plan hospital building is studied. The response of the structure in the time domain as recorded by highly sensitive sensor network, integrated by a data acquisition system. The identification was performed using techniques of modal extraction in the frequency domain (frequency Domain decomposition). A calibration process was applied in order to identify a reliable structural model to be used for the seismic vulnerability assessment of the hospital building. In particular, a nonlinear static procedure accounting for mass distribution, higher modes contribution and mode-shapes correlation was proposed for the estimation of the seismic response of irregular buildings. Finally, the influence of lateral force distribution, node control during pushover and accidental eccentricity is investigated.
The paper addresses two case studies of structural monitoring and seismic assessment of medieval masonry Towers in Italy: the bell tower of Aversa and the bell tower of Capua. These monuments in the Campania region were monitored by means of full-scale environmental vibration testing. Measured responses were then used for modal identification. The procedure is based on a typical finite element model updating technique based on vibration test results. Parameters optimization is carried out by minimizing a weighted error criterion relative to the building’s modal properties. A satisfactory improvement on modal parameters is thus obtained, resulting in a close Agreement between the modal properties observed in dynamic tests and those calculated from numerical model. Seismic assessment is carried out with nonlinear static analysis of the tower under multimodal distributions of lateral loads.
Nonlinear analysis indicates the potential collapse mechanisms and evidences dangerous structural weakness which may play a role in the seismic vulnerability of the towers.
Whenever the preservation of original substance obtains priority in a restoration task, reprofiling techniques using repair mortars are a welcome solution. For ordinary concrete repair aesthetic aspects are of minor importance whereas for the restoration of natural stone elements they come to the fore. Especially for listed buildings and monuments, historico-cultural and aesthetical interests become the ruling Parameters for planning and execution of restoration tasks. Nevertheless the technical and constructive requirements have to be considered and deterioration processes have to be understood to ensure sustainability and durability of the repair task. Due o differences in the Chemical and mineralogical composition, natural stone provides a vast variety of texture and colour. Also the range of different mechanical and durability related properties is far wider than found with concrete for example. A research project dealing with the development of a modular repair mortar System for natural stone is currently set up at the BAM. To provide the conservator with the best possible options to match colour, texture and technical requirements, the System will be setup on a modular basis. Several different binder Systems on basis of cement, lime and sodium Silicate as well as polymer based Systems are planned, which can be combined with different aggregate compositions and different pigments. To evaluate the mortar performance, test procedures will be defined for tests on mortar samples and on composite specimens. In the paper the experimental Programme will be explained and first results will be presented and discussed.