Filtern
Erscheinungsjahr
- 2019 (221) (entfernen)
Dokumenttyp
- Vortrag (221)
Sprache
- Englisch (132)
- Deutsch (85)
- Mehrsprachig (3)
- Russisch (1)
Referierte Publikation
- nein (221) (entfernen)
Schlagworte
- Additive Manufacturing (24)
- Additive Fertigung (18)
- Additive manufacturing (14)
- NDT (12)
- Thermografie (12)
- Concrete (11)
- Ultraschall (10)
- Ultrasound (10)
- Zerstörungsfreie Prüfung (10)
- Magnetocaloric (8)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (221) (entfernen)
Eingeladener Vortrag
- nein (221) (entfernen)
We compare four different sensing solutions suitable for distributed fiber optic humidity sensing in per uorinated graded-index polymer optical fibers (PFGI-POFs). Compared to silica fbers, polymer optical fibers over advantageous beneffits including signifficantly higher break down strain, fracture toughness and humidity sensitivity. Various humidity-related effects in PFGI-POFs have been reported in the last years including measured attenuation and length changes as well as Brillouin frequency and Bragg wavelength shifts. The four aforementioned methods could serve as a basis for distributed and quasi-distributed humidity sensing and are described here closely with an emphasis on plausible cross effects to temperature and strain. The main focus of this paper lies on the comparison of four approaches with regard to method complexity, sensitivity to humidity, spatial resolution, real-time capability and effort to compensate for cross effects.
The Spectral Element Method (SEM) has been proven to be an efficient numerical method for solving the wave equation in linear elastic bodies. This efficiency is reduced if a stress singularity is present in the body. For example, re-entrant corners, material interfaces, fixed boundaries, and especially crack tips can cause stress singularities. To preserve the efficiency of the SEM, special solution strategies are required. There are many approaches which consider stress singularities, but comparisons are rare for dynamic problems. Finding an efficient model is an important step for many applications. In particular, applications for structural health monitoring and non-destructive evaluation rely on accurate and efficient crack models.
In this contribution, we present several models to capture singularities in combination with the SEM. The theory behind the models are shortly summarized and we show results for different benchmark problems in two dimensions. The first model deploys a new class of singular elements. For these singular elements, the crack tip approximation is computed based on the static Scaled Boundary Finite Element Method (SBFEM). The second model uses the continued‐fraction‐based SBFEM, while the third model uses an hp-refinement near the singularity. The models are compared among each other and evaluated in terms of their respective efficiency and accuracy.
Recently, various guided wave tomography algorithms have been developed to map structural changes from remote locations. The focus has been on structures made of isotropic materials and little work has been done on structures made of anisotropic materials. Primary complication to implement tomography in composite laminates is associated with the complex forward model to accurately simulate the 3-D guided wave propagation. In this study, we demonstrate that guided wave propagation can be approximated by an equivalent 2-D acoustic model. It is based on finite-difference discretization method in which the wave-field is parameterized by phase velocity and dimensionless anisotropic parameters. The reconstruction of defects is based on a full-waveform inversion algorithm and was implemented on the data obtained from finite element simulations. Results on a localized stiffness defects in composite plates with various layups demonstrate the attractiveness of the proposed methodology.
The detection of delamination, rot and cracks causing a decrease of strength in wooden construction elements is a key task for nondestructive testing (NDT). Air-coupled ultrasound (ACU) is used to detect flaws without having to provide contact to the surface or otherwise affect the object. Novel ferroelectric transducers with a high signal-to-noise ratio enable an accurate flaw detection. Transducers made of cellular polypropylene (PP) are suitable for characterizing wood-based materials (WBM) because their extremely low Young’s modulus and low density mean a favorable acoustic impedance for the transmission of ultrasonic waves between the transducer and air. The transducers can be applied during the production of WBM and during its service life. The device enables a fast in-situ recognition of defects with frequencies between 90 kHz and 250 kHz. Measurements can be performed in through transmission for a high resolution or in pulse-echo technique in case of one-sided access at the expense of reduced signal strength. Ultrasonic quality assurance for wood is an important attempt to increase the acceptance of wooden structures and towards sustainability in civil engineering in general.
To date, there are very few technologies available for the conversion of low-temperature waste heat into electricity. Thermomagnetic generators are one approach proposed more than a century ago. Such devices are based on a cyclic change of magnetization with temperature. For thermomagnetic materials, we used a commercial magnetocaloric alloy with a transition temperature of 300 K.
Damage Quantification in Aluminium-CFRP Composite Structures using Guided Wave Wavenumber Mapping
(2019)
The use of composite materials is associated not only with the advantages of weight reduction and improved structural performance but also with the risk of barely visible impacts or manufacturing damages. One of the promising techniques for the detection and characterisation of such damages is based on ultrasonic guided wave propagation and analysis. However, the multimodal nature and dispersive behaviour of these waves make their analysis difficult. Various signal processing techniques have been proposed for easier interpretation of guided wave signals and extraction of the necessary information about the damage. One of them is the wavenumber mapping which consists of creating a cartography of the wavenumber of a propagating mode over an inspected area, using a dense wavefield acquisition measured for example with a scanning laser Doppler vibrometer. This technique allows both the quantification of the in-plane size and the depth of damage, for example, impact-induced delamination in composite laminates.
In this contribution, wavenumber mapping is applied to a delaminated aluminium-CFRP composite structure which corresponds to composite-overwrapped pressure vessels used for storing gases in aerospace and automotive industries. The analysis of experimental data obtained from measurements of guided waves propagating in an aluminium-CFRP composite plate with impact-induced damage is performed. The output of the imaging is a three-dimensional representation of the delamination induced by the impact. Good agreement between conventional ultrasonic testing and guided wave damage mapping can be found.
DICONDE für ET
(2019)
Diffraction-based experimental determination of Residual Stress in AM parts: A critical discussion
(2019)
Additive manufacturing (AM) technologies have experienced an exceedingly rapid growth, not always paralleled by the knowledge about the materials properties and performance. In particular, residual stress (RS) has been soon recognized as an issue in AM parts, so that parts are always post-heat-treated. Moreover, much effort has been spent on simulating RS, especially using finite element methods.
The experimental determination of RS has thereby become increasingly important, and even simple data constitute (to date) a piece of knowledge to fill the above-mentioned gap. In particular, diffraction methods, which are basically non-destructive, offer enormous possibilities to gain knowledge on real components, since neutrons and synchrotron radiation can penetrate even heavy metals up to several millimeters (or even centimeters). Indeed, some success has been obtained, and the knowledge about the origins of the RS fields, as well as their variation as a consequence of heat or mechanical treatments, has been greatly expanded.
In this talk, a few success stories will be outlined. It will be shown how the determination of RS in metallic parts (with focus on those produced by laser powder bed fusion) has even allowed showing that process parameters that were considered unimportant play a major role in the onset of stress.
However, while RS is starting to be considered in the part design, deposition strategy (e.g. build plate temperature), and even in the definition of the relevant metric to assess the quality of a part, much is still to be investigated about the hypotheses underlying its experimental determination. Therefore, some aspects to be aware of, or even to date unclear will also be discussed, such as the determination of the reference unstrained samples and of the principal axes of stress. All these aspects will draw the path towards a comprehensive understanding of the process-structure-performance relationships in AM materials and parts.