Filtern
Erscheinungsjahr
- 2012 (42) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (30)
- Beitrag zu einem Tagungsband (6)
- Vortrag (6)
Schlagworte
- Laser beam welding (6)
- Laser welding (5)
- Lorentz force (4)
- Electromagnetic weld pool support (3)
- Gas metal arc welding (3)
- Laserstrahlschweißen (3)
- Marangoni stresses (3)
- Natural convection (3)
- Rissbildung (3)
- Corrosion (2)
- Crack formation (2)
- Electron beam welding (2)
- Elektronenstrahlschweißen (2)
- Festigkeit (2)
- Heat treatment (2)
- Hochfester Stahl (2)
- Instrumentierte Eindringprüfung (2)
- Mechanical properties (2)
- Microstructure (2)
- Punktschweißverbindung (2)
- Resistance spot welding (2)
- Schweißnahtfehler (2)
- Simulation and calculation (2)
- Simulation und Berechnung (2)
- Spannungen (2)
- Spot welding (2)
- Stainless steel (2)
- Stress reduction (2)
- Stresses (2)
- Weld defects (2)
- Weldability (2)
- Welding simulation (2)
- Werkstofffragen (2)
- Wärmebehandlung (2)
- AZ31 magnesium alloy (1)
- Aluminium (1)
- Aluminium alloy (1)
- Austenitic (1)
- Austenitic stainless steels (1)
- Automotive industry (1)
- Beam welding (1)
- Buoyancy (1)
- CO2 laser (1)
- CO2 lasers (1)
- CO2- and Nd:YAG laser (1)
- Controlled tensile weldability test (1)
- Corrosion resistance (1)
- Cracks (1)
- Critical strains (1)
- Deformation (1)
- Duplex (1)
- Duplex stainless steels (1)
- Electromagnetic weld pool control (1)
- Electromagnetically controlled laser beam welding (1)
- Fahrzeugbau (1)
- Fatigue life (1)
- Finite element analysis (1)
- Fluid flow (1)
- Full penetration (1)
- GTA welding (1)
- Gap (1)
- Gas-shielded arc welding (1)
- Hardness (1)
- Hartmann effect (1)
- Heißrisse (1)
- High energy beam welding (1)
- High power laser beam welding (1)
- High strength steels (1)
- High-strength steel (1)
- Higher manganese content (1)
- Hot cracking (1)
- Hot cracking test (1)
- Kornfeinung (1)
- Laser metal deposition (1)
- Laser powder cladding (1)
- Laser scanner optics (1)
- Lokale Festigkeit (1)
- Lokale Spannungs-Dehnungskurven (1)
- Manganese (1)
- Marangoni convection (1)
- Material questions (1)
- Mechanical properties of joints (1)
- Multi-pass welding (1)
- Normen (1)
- Numerical simulation (1)
- Ortsaufgelöst (1)
- Pores (1)
- Porosity prevention (1)
- Post-weld heat treatment (1)
- Post-welding heat treatment (1)
- Process combinations (1)
- Process reliability (1)
- Process stability (1)
- Prozesskombinationen (1)
- Repair welding (1)
- Residual stress (1)
- Residual stresses (1)
- Schutzgasschweißen (1)
- Schweißeignung (1)
- Sensitivity analysis (1)
- Shear strength (1)
- Shielding atmosphere (1)
- Shielding gases (1)
- Solidification cracking (1)
- Spannungs-Dehnungskurve (1)
- Stainless austenitic and duplex steels (1)
- Stainless steels (1)
- Standards (1)
- Strain rates (1)
- Strength (1)
- Tack welding (1)
- Tensile strength (1)
- Tensileshear (1)
- Thermography (1)
- Ti-6Al-4 V (1)
- Torsion (1)
- V groove (1)
- WIG-Schweißen (1)
- Weld metal (1)
- Weld microstructure (1)
- Weld pool dynamics (1)
- Weld pool stabilization (1)
- Weldbonding (1)
- Welding-induced distortion (1)
- Welding-induced residual stress (1)
- Widerstandspressschweißen (1)
- YAG lasers (1)
Eingeladener Vortrag
- nein (6)
In the rough conditions in the fabrication of automobile bodies, it is not always possible to avoid welding-induced imperfections such as cracks during the resistance spot welding of high-strength steels. In this respect, the influence of such cracks on the fatigue strength particularly of modern high-strength austenitic steels is not sufficiently well-known at present. The influence of welding cracks with various positions and formations was therefore investigated within the framework of this paper. In this case, the analysis of the standardised stiffness courses of specimens and the comparison of the numbers of failure stress cycles served to prove that the surface cracks produced without any spatter in the centre, interfacial region and peripheral region of the weld nugget do not have any negative influence on the fatigue strength of the high-strength austenitic material investigated here. Specimens which were manufactured with welding spatter and exhibit cracks in the peripheral region show considerably higher numbers of failure stress cycles than crack-free reference specimens.
Die lokalen Festigkeiten im Bereich einer Schweißverbindung sind maßgebend für deren Widerstandsfähigkeit gegenüber mechanischen Beanspruchungen. Im Gegensatz zu anderen präparationsaufwendigen Methoden, z. B. die Untersuchung von Mikro-Zugproben, liefert die instrumentierte Eindringprüfung mit deutlich geringerem Aufwand Verläufe von Festigkeiten mit sehr guter Ortsauflösung. Im Rahmen dieser Arbeit werden wahre Spannungs-Dehnungskurven aus zyklischen Eindringversuchen mittels Auswertungen auf der Basis repräsentativer Spannungen und Dehnungen und auf der Basis neuronaler Netze an Punktschweißverbindungen aus hochfesten Stählen, jeweils im Bereich des Grundwerkstoffs und der Schweißlinse, bestimmt. Die Ergebnisse werden exemplarisch für einen Stahltyp mit Ergebnissen von Zugversuchen am Grundwerkstoff und am thermisch behandelten Werkstoff mit Schweißgut ähnlicher Struktur verglichen und diskutiert.
This article studies the three dimensional transient weld pool dynamics and the influence of groove angle on welding of low carbon structural steel plates using the ForceArc® process. The deformation of the weld bead is also calculated with an accurate coupling of the heat transfer with fluid flow through continuity, momentum and the energy equations combined with the effect of droplet impingement, gravity, electromagnetic force, buoyancy, drag forces and surface tension force (Marangoni effect). Different angles of V groove are employed under the same welding parameters and their influence on the weld pool behavior and weld bead geometry is calculated and analyzed, which is needed for subsequent calculations of residual stress and distortion of the workpiece.
Such a simulation is an effective way to study welding processes because the influence of all welding parameters can be analyzed separately with respect to heat transfer, weld pool dynamic, and microstructure of the weld. Good agreement is found between the predicted and experimentally determined weld bead cross-section and temperature cycles. It is found that the main flow pattern is more or less the same although the groove angle increases, but it will evoke larger amount of fluid to flow downward to get deeper penetration.
Thick-walled pipes made of steel are the basis of a large number of components in mechanical and installation engineering, e.g. for hydraulic components, in power station technology or in the petroleum industry. Particularly when strict positional and shape tolerances are demanded, the classical manufacturing process is chip-producing machining from the solid material. However, this is time-intensive and material-intensive. The laser/GMA hybrid processes with modern high-power lasers are a suitable alternative. With these processes, it is currently possible to weld components with a wall thickness up to approx. 15 mm with little distortion in one pass. However, in initial experiments, solidification cracks with longitudinal and vertical orientations in relation to the welding direction, so-called central line cracks, were established in welds on pipes. Within the framework of a research project, it was possible to determine the cause of the cracking and to find measures in order to avoid it. The technical boundary conditions could be complied with in this respect. The article gives an overview of the research project and the essential results.
Dickwandige Rohre aus Stahl sind die Basis einer Vielzahl von Komponenten im Maschinen- und Anlagenbau, zum Beispiel bei Hydraulikkomponenten, in der Kraftwerkstechnik oder der Petroindustrie. Insbesondere, wenn hohe Lage- und Formtoleranzen gefordert werden, ist das klassische Herstellungsverfahren ein Zerspanen aus dem Vollmaterial. Dies ist jedoch zeit- und materialintensiv. Als Alternative bieten sich die Laserstrahl-MSGHybridverfahren mit modernen Hochleistungslasern an. Mit diesen Verfahren ist es derzeit möglich, Bauteile bis zu etwa 15 mm Wanddicke verzugsarm und einlagig zu verschweißen. In ersten Experimenten wurden bei Schweißungen an Rohren jedoch in Bezug auf die Schweißrichtung längs und vertikal orientierte Erstarrungsrisse, so genannte Mittelrippendefekte, festgestellt. Im Rahmen eines Forschungsprojekts konnte die Ursache der Rissentstehung ermittelt und Maßnahmen zur Vermeidung gefunden werden. Dabei ließen sich die technischen Randbedingungen einhalten. Der Artikel gibt einen Überblick über das Forschungsprojekt und die wesentlichen Ergebnisse. ---------------------------------------------------------------------------------------------------------------------------------------
Thick-walled pipes made of steel are the basis of a large number of components in mechanical and installation engineering, e.g. for hydraulic components, in power station technology or in the petroleum industry. Particularly when strict positional and shape tolerances are demanded, the classical manufacturing process is chip-producing machining from the solid material. However, this is time-intensive and material- intensive. The laser/GMA hybrid processes with modern high-power lasers are a suitable alternative. With these processes, it is currently possible to weld components with a wall thickness up to approx. 15 mm with little distortion in one pass. However, in initial experiments, solidification cracks with longitudinal and vertical orientations in relation to the welding direction, so-called central rib defects, were established in welds on pipes. Within the framework of a research project, it was possible to determine the cause of the cracking and to find measures in order to avoid it. The technical boundary conditions could be complied with in this respect. The article gives an overview of the research project and the essential results.
In a repair process chain, damaged areas or cracks can be removed by milling and subsequently be reconditioned with new material deposition. The use of laser metal deposition has been investigated for this purpose. The material has been deposited into different groove shapes, using both stainless steel and Ti-6Al-4 V. The influence of welding parameters on the microstructure and the heat affected zone has been studied. The parameters have been modified in order to achieve low heat input and consequently low distortion as well as low metallurgical impact. Finally, an evaluation of the opportunities for an automatized repair process is made.
Die aktuelle Normung bezüglich mikroskopischer Untersuchungen von Schweißverbindungen und die Zulässigkeit von Mikrorissen sowie deren Definition ist nicht eindeutig. Nach der Darstellung derzeit gültiger Normen im Bereich der Bewertung von Schweißnähten, Qualifizierung von Schweißverfahren und Ausführung von Schweißverbindungen, wird auf Grundlage aktueller Schweißversuche an hochfesten vergüteten Feinkornbaustählen die Problematik von Mikrorissen diskutiert. Offene Punkte und Fragen bzw. Verbesserungsmöglichkeiten werden aufgezeigt und zur Diskussion gestellt. Schließlich wird auf die Klärung des Einflusses von Mikrorissen auf die mechanisch- technologischen Werkstoffkennwerte der Schweißverbindung unter statischer sowie zyklischer Beanspruchung hingewiesen. ---------------------------------------------------------------------------------------------------------------------------------------------------------------
Neither the latest standardisation with regard to microscopic investigations on welded joints nor the permissibility of microcracks and their definition are unambiguous. According to the representation of currently applicable standards in the fields of the assessment of welds, the qualification of welding processes and the execution of welded joints, the problems associated with microcracks are discussed on the basis of the latest welding tests on high-strength quenched-and-tempered fine-grained structural steels. Not only outstanding points and questions but also improvement possibilities are indicated and opened for discussion. Finally, attention is drawn to the clarification of the influence of microcracks on the mechanical- technological material parameters of the welded joint subjected to both static and cyclic stresses.
In various applications, welding-induced residual stresses have a substantial impact on the integrity of welded constructions. Tensile residual stress can promote stress-corrosion cracking, brittle fracture, and reduces the fatigue life in service, as well as influences component design due to critical stress concentrations within the component.
In the present paper, a six bead multi-pass gas metal arc weld of 20 mm thick structural steel S355J2+N is experimentally and numerically investigated. The studies include transient 2D and 3D numerical calculations which consider temperature-dependent material properties, phase transformations, 'thermal' tempering, transformation plasticity, volume change due to phase transformation, an elasticplastic material model, and isotropic strain hardening. The experimentally determined and calculated residual stresses are in a good agreement. Furthermore, the influence of the preheat and interpass temperature on welding-induced residual stresses is shown in the present investigation.
A single-layer pulsed gas metal arc weld of structural steel S355J2+N with a thickness of 5 mm is experimentally and numerically investigated. Two tack welds are considered in the numerical simulation into two different ways. First, the tack welds are represented by elements belonging to the initial material. This implies that the 'tack weld material' was not exposed to any thermal load or phase transformation before actual welding was performed. The weld seam is shortened and there is an influence on the stiffness of the whole structure affecting the calculation result. Secondly, the tack welds were simulated as conducted in the experimental welding procedure. The cases considering tack welding are compared to a simulation neglecting tack welding and to the experimental results.
The influence of tack welds on the calculated welding-induced distortion is clarified and a contribution to an improved simulation-based prediction of welding-induced distortion is possible by modeling tack welding according to the realistic fabrication procedure.