Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (11)
- Vortrag (3)
- Posterpräsentation (3)
Schlagworte
- Nucleation (17) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (3)
The demand for improved castability and low angle grain boundary (LAGB) resistance has led to the addition of low contents of e.g., B, Hf, Zr or C, into large industrial gas turbine components made of Ni-base superalloy single crystals (SXs). Due to the long-term application of Ni-base superalloy SX components in the temperature regime > 1000 °C, the formation of carbides is highly probable, which could jeopardize mechanical properties, such as high cycle fatigue. In the present contribution, the effect of internal and external stresses on the nucleation and growth characteristics of M23C6 carbides is investigated. Creep experiments are performed on the Ni-base superalloy SX LEK 94, which shows a low C concentration (= 0.1 at. %), at 1020 °C under parallel and circularly notched tensile specimens at a nominal stress of 160 MPa in the crystallographic direction [001]. The carbides are then characterized via scanning (S) and transmission (T) electron microscopy (EM). Nucleation is enhanced in the dendritic cores, often as coalesced colonies, extending over micrometers within M-rich (M: Cr, Re, W, Mo) γ channels. Lath shapes with facets on {100} (parallel to growth direction) and {111} are common. These facets exist since early stages (Fig.1a) and later develop misfit dislocations (Fig.1b), preserving the orientation relationship {100}γ || {100}M23C6. Fig. 1c shows a region from the creep gage, where carbides interact with superdislocations in the γ’ phase. Possible mechanisms are discussed.
The transformation of amorphous precursors into crystalline solids and the associated mechanisms are still poorly understood. We illuminate the formation and reactivity of an amorphous cobalt phosphate hydrate precursor and the role of water for its crystallization process. Amorphous cobalt phosphate hydrate nanoparticles (ACP) with diameters of ∼20 nm were prepared in the absence of additives from aqueous solutions at low concentrations and with short reaction times. To avoid the kinetically controlled transformation of metastable ACP into crystalline Co₃(PO₄)₂ × 8H₂O (CPO) its separation must be fast. The crystallinity of ACP could be controlled through the temperature during precipitation. A second amorphous phase (HT-ACP) containing less water and anhydrous Co₃(PO₄)₂ was formed at higher temperature by the release of coordinating water. ACP contains approximately five molecules of structural water per formula unit as determined by thermal analysis (TGA) and quantitative IR spectroscopy. The Co²+ coordination in ACP is tetrahedral, as shown by XANES/EXAFS spectroscopy, but octahedral in crystalline CPO. ACP is stable in the absence of water even at 500 °C. In the wet state, the transformation of ACP to CPO is triggered by the diffusion and incorporation of water into the structure. Quantitative in situ IR analysis allowed monitoring the crystallization kinetics of ACP in the presence of water.
Fukuda et al. published a paper (Scripta Mater. 68 (2013) 984–987) in which they claimed to be able to determine the isothermal nature of the martensitic transformation in a Ti–Ni alloy. They analyzed the evolution of electrical resistance during isothermal holding stages and concluded that the variations were a consequence of the isothermal transition between austenite and martensite. In the following we will demonstrate that the discussed data do not allow the interpretation presented and that the isothermal nature is not proved.
The formation mechanisms of silver nanoparticles using aqueous silver perchlorate solutions as precursors and sodium borohydride as reducing agent were investigated based on time-resolved in situ experiments. This contribution addresses two important issues in colloidal science: (i) differences and analogies between growth processes of different metals such as gold and silver and (ii) the influence of a steric stabilizing agent on the growth process. The results reveal that a growth due to coalescence is a fundamental growth principle if the monomer-supplying chemical reaction is faster than the actual particle formation.
Glass bricks are important transparent building materials. They are produced by joining two halves of glass pressings at 600700 °C. During this production process alkali oxides evaporate and are redeposited at the cooler inner front surfaces of the bricks. This surface layer reacts with H2O and CO2 from the residual brick atmosphere, leading to the formation of an alkali-rich silicate-hydrate layer of ≥50 nm thickness, which could be evidenced leading to a reduced nano-hardness of similar thickness, and from which NaHCO3 crystals can finally grow. Climate chamber experiments (repeated cooling between at -8 and -14 °C and reheating to 0 to 15 °C) resulted in reversible NaHCO3 crystallization and redissolution, presumably influenced by water evaporation or condensation and driven by the NaHCO3 supersaturation of the silicate-hydrate layer. Depending on the timetemperature schedule, different crystal morphologies became visible in this closed system, e.g. isolated spherical crystals, crystals arranged in chains and in double-chains, respectively, which can limit already the transmittance of the glass bricks. When a crack occurs or the brick is opened, the hygroscopic NaHCO3 crystals take up more H2O from the ambient, react irreversibly with the glass surface, finally leading to a total loss of transmittance.
The adsorption and condensed film formation of dodecyl (DTAB)-, tetradecyl (TTAB)-, hexadecyl (CTAB)-, and octadecyl (OTAB)-trimethylammonium bromides on the hanging mercury electrode is studied in KBr as supporting electrolyte, at various temperatures from 5 to 45 °C. A condensed film is formed at negative potentials and at room temperature only in the presence of CTAB. The decrease of the temperature favors the formation of the condensed film. A transition temperature is observed for the film formation. Capacitytime curves at the potentials where the film is formed show a nucleation and growth mechanism, with induction time depending not only on the final potential but also on the initial potential range, although it is in the desorption region. In this temperature range no film is observed for DTAB and TTAB. However, the film is observed for OTAB, but only at higher temperatures, and is more easily formed with increasing temperature. The film is formed in a certain potential region and the nucleation rate increases while moving toward more negative potentials. Hysteresis phenomena are observed during changes of scan direction. The capacity vs time curves for OTAB, where condensed film is formed, are treated using an Avrami plot formulation and have been explained as progressive one-dimensional nucleation with a decrease of the nucleation rate during the overall film formation. The results show a marked effect of the chain length of the alkyl chain on the film formation.