Filtern
Erscheinungsjahr
- 2011 (2247) (entfernen)
Dokumenttyp
- Vortrag (985)
- Zeitschriftenartikel (439)
- Posterpräsentation (401)
- Beitrag zu einem Tagungsband (331)
- Beitrag zu einem Sammelband (32)
- Forschungsbericht (18)
- Dissertation (13)
- Buchkapitel (12)
- Sonstiges (8)
- Zeitschriftenheft (Herausgeberschaft für das komplette Heft) (4)
Sprache
- Deutsch (1643)
- Englisch (595)
- Französisch (2)
- Mehrsprachig (2)
- Russisch (2)
- Italienisch (1)
- Polnisch (1)
- Chinesisch (1)
Schlagworte
- Corrosion (13)
- Fluorescence (13)
- Recycling (13)
- Steel (11)
- Concrete (10)
- Monitoring (10)
- Beton (9)
- CCS (9)
- Korrosion (9)
- Flame retardancy (8)
Eingeladener Vortrag
- nein (985)
The present work shows results on elemental distribution analyses in Cu(In,Ga)Se2 thin films for solar cells performed by use of wavelength-dispersive and energy-dispersive X-ray spectrometry (EDX) in a scanning electron microscope, EDX in a transmission electron microscope, X-ray photoelectron, angle-dependent soft X-ray emission, secondary ion-mass (SIMS), time-of-flight SIMS, sputtered neutral mass, glow-discharge optical emission and glow-discharge mass, Auger electron, and Rutherford backscattering spectrometry, by use of scanning Auger electron microscopy, Raman depth profiling, and Raman mapping, as well as by use of elastic recoil detection analysis, grazing-incidence X-ray and electron backscatter diffraction, and grazing-incidence X-ray fluorescence analysis. The Cu(In,Ga)Se2 thin films used for the present comparison were produced during the same identical deposition run and exhibit thicknesses of about 2 µm. The analysis techniques were compared with respect to their spatial and depth resolutions, measuring speeds, availabilities, and detection limits.
With the publication of EN ISO 6892-1:2009, the harmonisation of tensile testing at room temperature in Europe was achieved by combining EN 10002-1:2001 with ISO 6892:1998. Essential changes are the introduction of the strain rate and the strain rate control as the significant testing rate or control mode, respectively, referred to as “Method A”. By using this method in the correct way it is guaranteed that in the moment of determination of properties comparable resulting strain rates at the test piece in smaller ranges of specified strain rates are adopted — also if different stiffnesses of the testing equipment are present. This leads especially for strain rate sensitive materials to better comparable results. In this paper it is documented the need for the implementation of method A, methods for the realisation — also by the use of older testing systems — and an example of the comparability of results of the methods for a strain-rate-sensitive-steel.
Mit der Veröffentlichung der DIN EN ISO 6892-1:2009 wurde für den Zugversuch bei Raumtemperatur eine Harmonisierung der in Europa verbindlichen EN 10002-1:2001 mit der ISO 6892:1998 erreicht. Wesentliche Änderungen sind die Einführung der Dehngeschwindigkeit und der Dehngeschwindigkeitsregelung als maßgebliche Prüfgeschwindigkeit bzw. Regelungsart, als Verfahren A bezeichnet. Mit der korrekten Anwendung dieses Verfahrens wird gewährleistet, dass im Moment der Kennwerteermittlung bei enger spezifizierten zulässigen Dehngeschwindigkeitsbereichen vergleichbare resultierende Dehngeschwindigkeiten an der Probe auch bei unterschiedlichen Steifigkeiten der Prüfaufbauten vorliegen. Dieses führt besonders bei dehngeschwindigkeitssensitiven Werkstoffen zu deutlich vergleichbareren Ergebnissen. In diesem Beitrag wird auf die Notwendigkeit der Einführung des Verfahrens A, der möglichen Umsetzungen auch bei Verwendung von älteren Prüfsystemen sowie exemplarisch auf vergleichende Ergebnisse der Verfahren an einem dehngeschwindigkeitssensitivem Stahlwerkstoff eingegangen.