Filtern
Erscheinungsjahr
- 2011 (27) (entfernen)
Dokumenttyp
- Vortrag (12)
- Beitrag zu einem Tagungsband (10)
- Zeitschriftenartikel (4)
- Beitrag zu einem Sammelband (1)
Schlagworte
- Inversion (2)
- Luftultraschall (2)
- Magnetic flux leakage (2)
- Active thermography (1)
- Air-coupled ultrasonic transducers (1)
- Aktive Thermografie (1)
- Aktive thermografie (1)
- Akustische Impedanz (1)
- Blitzlichtanregung (1)
- Crack sizing (1)
Eingeladener Vortrag
- nein (12)
The extremely low acoustic impedance of polypropylene ferroelectret combined with its piezoelectric properties makes this material suitable for construction of aircoupled ultrasonic transducers for non-destructive testing. For the fabrication of transducers with a stable quality, the reproducibility of their key parameters is of interest.
The reproducibility was evaluated by means of (i) impedance spectroscopy and (ii) pulse-echo measurements. (i) Impedance spectroscopy was applied to identify the resonance frequency, the coupling factor and the acoustic impedance of several nominally identical transducers. (ii) Pulse-echo measurements yielded the signal form of these transducers.
The variation of the signal amplitude measured with pulseecho technique was about 10 dB. A part of this variation Comes from the deposition of transducer electrodes and another part from local variations of ferroelectret properties. The variation of the signal amplitude was caused by the observed variation of the coupling factor, which was also about 10 dB. The variation of the acoustic impedance was only about 1 dB, thus having no effect on the variation of the signal amplitude.
These results indicate that the variability can be reduced by improving the control of electrode deposition and by optimizing the production technology affecting the reproducibility of material properties.
Charakterisierung der Wandler für Luftultraschallprüfung aus zellulärem Polypropylen-Ferroelektret
(2011)
In den letzten Jahren stieg die Anfrage für zerstörungsfreie Prüfung (ZIP) mit Luftultraschall deutlich. Die klassische ZfP mit Ultraschall nutzt Flüssigkeiten als Koppelmittel zwischen dem Wandler und dem Prüfkörper. Für die Prüfung von Gegenständen mit empfindlicher Oberfläche, die das Koppelmittel beschädigen oder verunreinigen kann, ist deswegen Luftultraschall besser geeignet. Eine mögliche Anwendung ist beispielsweise der Nachweis von Delaminationen in glas- und kohlefaserverstärkten Verbundwerkstoffen sowie Sandwichbauteilen, die in der Luftfahrt- und der Automobilindustrie eingesetzt werden.
The structures and properties of silver selenide samples strongly depend on the method of preparation. Thin films prepared by pulsed laser deposition (PLD) contain lamellae of two low-temperature modifications of Ag2Se whose structures were analyzed in detail by electron microscopy techniques. Besides the stable and known Naumannite-type phase (LT1), a metastable phase was observed (LT2), and the phase transformation was examined in situ. Via cooling and annealing, LT2 becomes dominant in thin films, thus enabling solving the structure of LT2 by electron diffraction. These experiments and HRTEM point to an Acanthite-type (stable low-temperature modification of Ag2S) structure of LT2. Rapid-quenching procedures were applied for the first synthesis of LT2 as bulk sample. Depending on the conditions of melt spinning experiments, well-defined products were formed. In one series, we found a separation of LT1 and LT2 into distinct morphologies, i.e. microspheres and dendrites, respectively. The results on the magnetoresistance of the rapidly quenched materials support previous work.
High-precision magnetic field sensors are of increasing interest in non destructive testing (NDT). In particular GMR-sensors (giant magneto resistance) are qualified because of their high sensitivity, high signal-to-noise ratio and high spatial resolution. We performed magnetic flux leakage measurements of artificial cracks with a GMR-gradiometer and a 3-axes GMR-magnetometer. Cracks of a depth of 44 μm still could be detected with a sufficient high signal-to-noise ratio. A semi-analytic magnetic dipole model was used for swiftly predicting magnetic stray fields. The reliable reconstruction based on measurements of artificial rectangular-shaped defects is demonstrated.
In diesem Beitrag wird ein neuartiger Ansatz zur Erzeugung von Luftultraschall vorgestellt, der auf dem thermoakustischen Prinzip beruht. Mikro- und nanostrukturierte Kohlenstoffmaterialien werden dabei mit einem harmonischen Wechselstrom gespeist und erfahren durch ohmsche Verluste eine Temperaturänderung, die sich auf das umgebende Fluid überträgt. Daraus resultieren Druckmodulationen, und es wird eine ausbreitungsfähige Schallwelle erzeugt. Dabei tritt Frequenzverdopplung gegenüber der Anregungsfrequenz auf. Es konnte gezeigt werden, dass der entscheidende Parameter für die Effizienz der Methode, d.h. für ein möglichst großes Verhältnis von Schalldruck zu eingebrachter Leistung, die Wärmekapazität pro Flächeneinheit ist. Da dieser Quotient für Kohlenstoffmaterialien sehr klein sein kann, erlaubt das thermoakustische Prinzip hier die effiziente Erzeugung von Luftultraschall. Schalldruckmessungen an verschiedenen Materialproben wurden bis 100 kHz mit einem Mikrofon durchgeführt, oberhalb von 100 kHz wurde eine laservibrometrische Schnellemessung eingesetzt. In experimentellen Untersuchungen wurde die Schallerzeugung in Abhängigkeit der Materialeigenschaften analysiert und systematisiert. Die experimentellen Ergebnisse wurden mit numerischen und analytischen Berechnungsergebnissen verglichen.
Progress in Acoustical Defect Sizing NDT Methods for the Inspection of Power Plant Components
(2011)
Thermoacoustic generation of airbone ultrasound using carbon materials at the micro- and nanoscale
(2011)
The paper presents numerical methods to detect and classify defects and inhomogeneities by means of active thermography. The objective is to determine the wall thickness of structure elements with an inaccessible back wall, for example, of pipes or Containers. As test specimens we used approximately 2 cm thick PVC samples with spatial variations in the back wall geometry. Flash lamps provided the heating. To know the thickness of the wall, we used two inversion methods and compared the results achieved. One is an iterative echo defect shape method and already tested on Steel test specimens with good reconstruction results. The second one is the Levenberg-Marquardt method, applied here to thermographic data for non-destructive testing. Since data capturing using active thermography and the presented numerical methods can easily be automated, the combination of these two procedures is a promising approach providing a broad area of application.
Fast defect parameter estimation based on magnetic flux leakage measurements with GMR sensors
(2011)
We present a fast inverse scheme that is capable of simultaneously estimating the parameters depth, opening and length for rectangular 3D geometries of surface-breaking defects. The parameter estimation is realized by an iterative least-squares minimization using the trust-region reflective algorithm. A semi-analytic magnetic dipole model that allows the sensor characteristics to be incorporated is used for predicting the stray magnetic fields. Giant magneto-resistance (GMR) measurements were carried out on a test specimen that includes a series of artificial defects. For the estimation of the defect depths relative errors between 0.6% and 15.9% have been obtained. Due to its very low computational costs, the inverse scheme can suitably be employed in automated production environments.
We present an all-purpose crack detection algorithm for flying spot thermography which is directly applicable to a thermogram sequence without the need of any additional information about the experimental setup. A single image containing distinct crack signatures is derived in two steps. Firstly, the spatial derivative is calculated for each frame of the sequence and, secondly, the resulting data set is sorted pixel wise along the time axis. The feasibility of the proposed procedure is proven by testing a piece of rail that comprises roll contact fatigue cracks and by comparing the results with magnetic particle testing.