Filtern
Erscheinungsjahr
- 2019 (9) (entfernen)
Dokumenttyp
- Vortrag (6)
- Beitrag zu einem Tagungsband (2)
- Posterpräsentation (1)
Sprache
- Englisch (9) (entfernen)
Referierte Publikation
- nein (9)
Schlagworte
- Fibre break (8)
- Multiscale model (7)
- Composite pressure vessels (6)
- Reduced volume method (3)
- Integral range (2)
- Composite Pressure Vessel (1)
- Composite pressure vessel (1)
- Correlation length (1)
- Correlation width (1)
- Fibre misalignment (1)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (6)
The reduced volume method has found a particular zone to be used for evaluating the strength of unidirectional composite materials. To validate the method, modelling an experimental test where it has the same basic assumption of the model had been carried out. The result was favourable as the model can predict the average value from the experiment and also the time dependent effect.
A general explanation of reduced volume method was introduced. This has allowed the simulation runs much faster without compromising the failure prediction of the multiscale fibre break model. The validation results with a material samples were shown. A certain mesh configuration to evaluate the cylinder has also been found to be the most effective in terms of computation time and prediction accuracy.
A high resolution micro-CT scan of a hoop layer from type IV cylinder has been carried out. The directional Gradient function had been used to analyse the in-plane and out-of-plane fibre misalignment from the Micro-CT Images. A correlation Analysis of the directional Gradient has also been performed and compared with the existing results from the cited paper.
The reduced volume method has been studied using the fibre break model from Mines ParisTech. This method allows less 3D finite elements to be used for predicting the failure of real scale composite structures. A favourable comparison results with racetrack specimens has been achieved. However, the comparison study with a type IV pressure vessels still requires more Evaluation.
Based on the burst test results conducted at BAM, loading rates will affect the strength of composite pressure vessels (CPV). The multiscale fibre-break model developed at Mines ParisTech is able to described this behaviour explained by the stress relaxation in the viscoelastic matrix. The experiment showed an increase of burst pressure when an extreme slow loading rate is used compare to the slow loading rate. Is is then discovered that the model could predict well for the slow loading rate but not for the extreme slow loading rate. It may have something to do with the fibre re-orientation of the hoop layer during the extreme slow loading rate test. Further investigation is required to discover this hypothesis.
It is pertinent to have a correct description of fibre strength described by the twp parameter Weibull distribution when evaluating a type Iv pressure vessel using the fibre break multiscale model developed at Mines ParisTech. Earlier studies have shown a positive comparison result when T600S fibre strength were used. This study has discovered what would be the effect on the predicted strength when T700S strength is used.
The effect of different Weibull parameter from different carbon fibres to predict the failure of a type IV pressure vessel has been analysed. In addition, the effect of the shape and scale parameter has also been done. T700S fibres gave higher burst pressure prediction as it has higher scale parameter and higher stiffness of the fibres. When smaller scale parameter is introduced, lower burst pressure prediction was found and vice versa. Whereas, higher burst pressure prediction was observed when smaller shape parameter was used and vice versa. The latter must have something to do with the higher probability of stronger and weaker fibres in the smaller percentile.
The Reduced Volume Method (RVM) has been used to evaluate the multiscale fibre break model developed at Mines ParisTech. It allows the model to be assigned only at certain part of the structures without necessarily compromising the final prediction. An attempt to model a simple unidirectional composite structure has also been carried out and gave a satisfying result. This paper deals with the application of the RVM to real scale type IV composite cylinders, where its stacking sequence was evaluated through micro-CT scans conducted with the collaboration of the University of Southampton. Two modelling geometries were evaluated and compared with the corresponding experimental results.