Filtern
Erscheinungsjahr
- 2013 (473) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (473) (entfernen)
Sprache
- Englisch (377)
- Deutsch (90)
- Mehrsprachig (4)
- Portugiesisch (1)
- Russisch (1)
Schlagworte
- Corrosion (8)
- Degradation (7)
- Nanoparticles (7)
- Flame retardancy (6)
- Fluorescence (6)
- Fluoreszenz (6)
- Imaging (6)
- Electrochemical noise (5)
- Faserverbundwerkstoffe (5)
- Mass spectrometry (5)
Experiments in this study reveal that the initiating capability of commonly used squibs is not high enough to initiate PETN in all cases. The fulfilment of the ‘new’ essential safety requirement 4 as set out in the European directive 2013/29/EU and the categorization of squibs as theatrical pyrotechnic articles (T2) can therefore be justified, as the explosive investigated belongs to quite a sensitive type (Initiation with low impulse energies possible). Underwater initiating capability tests according to EN 13763-15 led to meaningful results, showing that squibs are usually unable to initiate a secondary explosive. For a general assessment of the initiating capability of squibs and comparable (theatrical) pyrotechnic articles a threshold range of an equivalent initiation capability in grams of PETN on the basis of the performed underwater initiating capability tests was determined. It was found that squibs are generally not capable of initiating secondary explosives if the underwater initiating capability test showed an equivalent Initiation capability below 0.25 g PETN. As a consequence of this result, the underwater initiating capability test gives an effective and safer alternative to the experimental confirmation of the ‘new’ ESR 4 by direct contact of the article with the secondary explosive and should then be preferred to it.
The potentialities of a thin layer of steel-fiber reinforced self-compacting concrete (SFRSCC) for the flexural strengthening of handmade brick structural elements are investigated. For this purpose, an experimental program was carried out covering the relevant phenomena that can influence the effectiveness of this technique. The SFRSCC has a post-cracking residual tensile strength capable of improving the flexural stiffness, flexural resistance and ductility of prototypes representatives of ancient handmade brick based structures that fail in bending. To appraise the flexural strengthening effectiveness of this technique, straight beams composed of handmade bricks, low-strength mortar (LSM) and SFRSCC were tested. The obtained results have shown that this technique can increase significantly the flexural stiffness and resistance, and the ductility performance of this type of structures. The strengthening effectiveness depends on the post-cracking residual strength of the SFRSCC, its layer thickness and on the possibility of replacing part of the LSM by SFRSCC. Based on the experimental results for the characterization of the intervening materials, and adopting a cross section layer model capable of predicting the moment-curvature relationship for the distinct types of cross sections of this structural system, the maximum load registered in the tested prototypes was predicted with good accuracy.
Mechanically interlocked molecules (MIMs) such as rotaxanes and catenanes are capable of mechanical motion on the nanoscale and are therefore promising prototypes for molecular machines in recent nanotechnology. However, most of the existing examples are isotropically distributed in solution, which prohibits concerted movement and with it the generation of macroscopic effects. Thus, arranging them in ordered arrays is of huge interest in recent research. We report the deposition of quite densely packed multilayers of tetralactam macrocycles on gold surfaces by metal-coordinated layer-by-layer self-assembly. Linear dichroism effects in angle-resolved NEXAFS spectra indicate a preferential orientation of the macrocycles. The sequence of the metal ions can be programmed by the use of different transition metal ions at each deposition step. Additionally, reversible on-surface pseudorotaxane formation was successfully realized by repeated uptake and release of axle molecules inside the macrocycles cavities.
Ultrasonic vibration enhanced friction stir welding (UVeFSW) is a recent modification of conventional friction stir welding (FSW), which transmits ultrasonic vibration directly into the localized area of the workpiece near and ahead of the rotating tool. In this study, a high strength aluminium alloy (2024-T4) was welded by this process and conventional FSW, respectively. Then tensile tests, microhardness tests and fracture surface analysis were performed successively on the welding samples. The tests results reveal that ultrasonic vibration can improve the tensile strength and the elongation of welded joints. The microhardness of the stir zone also increases.
The study of protein corona formation on nanoparticles (NPs) represents an actual main issue in colloidal, biomedical and toxicological sciences. However, little is known about the influence of polymer shells on the formation and time evolution of protein corona onto functionalized NPs. Therefore, silicapoly(ethylene glycol) core–shell nanohybrids (SNPs@PEG) with different polymer molecular weights (MW) were synthesized and exhaustively characterized. Bovine serum albumin (BSA) at different concentrations (0.1–6 wt%) was used as model protein to study protein corona formation and time evolution. For pristine SNPs and SNPs@PEG (MW = 350 g/mol), zeta potential at different incubation times show a dynamical evolution of the nanoparticle–protein corona. Oppositely, for SNPs@PEG with MW ≥2000 g/mol a significant suppression of corona formation and time evolution was observed.
Furthermore, AFM investigations suggest a different orientation (side-chain or perpendicular) and Penetration depth of BSA toward PEGylated surfaces depending on the polymer length which may explain differences in protein corona evolution.
Pole figures are often used to present crystal orientation data. The huge number of single orientation measurements acquired by electron backscatter diffraction (EBSD) poses a challenge for pole figure representation due to the large number of calculations required. This significantly reduces the speed at which the data may be rotated and affects the ability to switch between different projection types. In the present work, it will be shown that satisfactory representation of orientation data in different projection types can generally be achieved by an imaging of a spherical projection. With this approach, explicit calculation of the projections is no longer required, allowing for both real-time dataset rotation and real-time switching between all projection types relevant to materials science. The technique can be applied to any other directional property distribution, for example, not only for EBSD orientation presentation.
A concept based on the application of a cube as a general polyhedron is presented for the visualization of point group symmetry. The cube is used to represent both the highest and lowest crystal symmetries, with differences observable as patterns characteristic to each point group. Patterns are generated using direction-specific color keys, which enable the recognition of point group-specific distribution of vectors in an external reference frame. For the visualization of the incoherent hexagonal crystal classes, two twinned cubes are applied in order to generate symmetry operators that would otherwise be missing. The resulting hexagonal dipyramid is described in the frame of a cube, reducing the number of used symmetry operators from 72 to 60. The complete set of 32 polyhedra are suitable, for example, as a visual aid for understanding the crystal symmetry and/or sub- and supergroup relationships.
Since the BSE signal depends on many factors, like the chemistry of the phase and the acceleration voltage, the size and position of the detector array is (slightly) different from phase to phase so that an (iterative) post-processing of the stored patterns is highly recommended. The derived BSE signal can be used for phase assignment in high resolution and high speed maps when EBSD fails and/or EDS (energy dispersive spectroscopy) needs too much time for a suitable and parallel signal acquisition.
Automated electron backscatter diffraction (EBSD) is generally unable to distinguish between multiple cubic phases in a specimen without additional information, such as that obtained by simultaneous energy dispersive X-ray spectroscopy (EDS). Small particles of phases with relatively similar compositions push the limits of phase identification using simultaneous EBSD and EDS, and a mismatch exists between the spatial resolutions of these two techniques due to them having different electron interaction volumes. In a recent paper, the present authors explored using backscatter detectors mounted on top of the EBSD detector to obtain atomic number (Z) contrast images that could be used for phase segmentation in cases where the results from the EBSD and EDS signals remain ambiguous. In the present work, we show that similar information can be obtained from the raw EBSD patterns themselves at higher spatial resolution than was obtained from the backscatter detectors, with the additional advantage of having no spatial mismatch between the data collection grids.
Mechanism of porosity growth during homogenisation in single crystal nickel-based superalloys
(2013)
Several mechanisms for porosity growth in single crystal nickel-based superalloys during homogenisation heat treatment have been proposed in the literature. They were carefully checked using different experimental methods, namely quantitative light microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and density measurements. It is shown that the main mechanism is the Kirkendall–Frenkel effect, i.e. generation of voids due to uncompensated efflux of Al atoms from dissolving γ/γ′-eutectic areas. The Al diffusion is supported by the afflux of vacancies from surrounding γ-matrix which results in porosity growth. This conclusion is confirmed by the estimation of the vacancy afflux towards the dissolving eutectic.