Filtern
Dokumenttyp
- Zeitschriftenartikel (6) (entfernen)
Sprache
- Englisch (6) (entfernen)
Schlagworte
- Anisotropy (1)
- Crack detection (1)
- Dissimilar weld (1)
- Echotomography (1)
- Eddy current testing (1)
- Extension of the inspection volume (1)
- Inservice inspection (1)
- NDT reliability (1)
- Phased array (1)
- Phased array concept (1)
Weld inspection using ultrasonic pulse-echo techniques needs high skilled operators especially if geometrical indications must be taken into consideration. A clear separation between geometrical indications and defects like cracks must be guaranteed. This requirement needs sensitive techniques like the 45(deg) shear wave technique using the mirror effect. Since more than twenty years the Time Of Flight Diffraction technique (TOFD) is still under discussion for defect sizing. But on the other hand the potential of the TOFD technique for defect detection is described in technical papers of manufacturers. The main task of examinations carried out at BAM was the comparison about the detectability of surface breaking cracks between the common methods and the TOFD approach.
The comparison of probes for the inspection of cladding shows a remarkable fact: depending on the reflectors used, a different performance characterization of the probe must be expected. It seems important for performance demonstration trials - especially those including the underclad area - to use reflector types as close as possible to the real cracks to be detected. For different detection approaches, reflectors representing underclad cracks should have a reduced diffraction at the crack tip areas in order to check their potential to detect the indication based on surface reflections of the ultrasonic waves.
The spherical bottom of BWR-pressure vessels contains holes for the nozzles of control rods and instrumentation. Up to now the detectable areas for the ultrasonic inspection are the accessible ligaments between the nozzles with an orientation parallel and transverse to the manipulator rails. Some licensing authorities demand an inspection technique capable of reliably detecting significant crack initiation in all critical areas near the cladding of the spherical inner surface. By order and in cooperation with the Hamburgische Electricitätswerke (HEW) we have developed a computer controlled equipment with two ultrasonic probes containing four linear arrays and a digitized A-scan storage for documentation and evaluation of inspection results. The manipulator guided probe movement in the paths between the nozzles of the spherical bottom is controlled by a computer program. This program determines for each array system and for each coupling position the beam angle as a function of the variable skewing angle to realize detection conditions suited to possible crack positions at the longitudinal, transverse and diagonal ligaments between the nozzles for control rods and instrumentation.
The inspection of the sealing weld is an important phase for the evaluation of the acceptability of final disposal canister, but the weld is only a part of the 3D shielding of copper shell. The main tasks for reliable NDT evaluation requires an extensive evaluation of the parameters which contains typical inspection related items like repeatability, S/N ratio, POD, setting up the equipment for inspection, and all practices for inspections. The other parameters are material parameters, their variation must be taken into account in the evaluation of NDT reliability. Further parameters include human factors, i. e. human inspectors and their interaction with technical systems; their effects were studied on an example of the evaluation of eddy current data. Final parameters are related to evaluation of detected defects, which means sizing and base for acceptance and this can be done in different ways. Some examples are given and results are compared with different methods for instance between radiographic testing and ultrasonic testing by raw data analysis and PA-SAFT results. Also, preliminary curves for the evaluation of metallographic results of 55 defects will be shown by EB weld measurements. Some practical items concerning copper inspections will be also discussed related to acceptability.
Defect sizing is required for a quantitative assessment of the quality and reliability of safety relevant components and materials using ultrasonic non-destructive testing. The SAFT (Synthetic Aperture Focussing Technique) and the TOFD technique (Time Of Flight Diffraction) are such promising sizing candidates, extracting more information from the raw ultrasound echo data and the corresponding crack tip response. In this work the phased array technique is used to inspect a clad mock-up model of a pressure vessel section. The full scale model contains artificial test reflectors which are located in the weld and in the cladding region as well. The defects—representing typical flaws at a very early stage—are analysed with different frequencies, beam angles and directions of incidence.
For the reconstruction of reflector indications a SAFT algorithm is applied to the phased array measurement results. Additionally the reflectors are analysed by means of the TOFD technique, using different beam angles at the same time. Both analysis methods are performed using different directions of incidence considering the complex cladding structure underneath the inner surface of the mock-up model. A direct comparison of the SAFT and TOFD techniques shows that, besides the clarity of the results, the detection and sizing capabilities of SAFT are far better.