Filtern
Erscheinungsjahr
- 1996 (48) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (48)
Sprache
- Englisch (37)
- Deutsch (10)
- Mehrsprachig (1)
Referierte Publikation
- ja (48) (entfernen)
Schlagworte
- Korrosion (2)
- Kristallisation (2)
- NEXAFS (2)
- Oberflächenanalyse (2)
- Polymeroberfläche (2)
- Reibung (2)
- Röntgenadsorptionsspektroskopie (2)
- Thermoplaste (2)
- Adhäsion (1)
- Aktivität, optische (1)
Depth profiles of layer systems consisting of different film materials and having different thicknesses are of great practical importance. Multilayer reference coatings of conducting (Ti/Al) and non-conducting (SiO2/Si3N4) material are analyzed with Auger electron spectroscopy (AES) and glow discharge optical emission spectroscopy (GDOES) depth profiling. Deposition techniques, physical vapor deposition for Ti/Al layers and plasma-enhanced chemical vapor deposition for SiO2/Si3N4 layers, as well as measurement and testing procedures for the determination of layer thickness such as optical and mechanical stylus and spectroscopie ellipsometry are discussed. GDOES depth profiles in direct current (d.c.) and radio frequency (r.f.) mode are related to measurements of crater profiles and compared with line scans and depth profiles performed by AES. It is shown that such multilayer reference systems are appropriate for calibration of depth profiles, i.e. the definition and the evaluation of the depth resolution at the interface, the determination of sputter rates both for d.c.- and r.f.-GDOES and AES, the optimization of the conditions of analysis, and the quantification of analysis itself.
The comparison of probes for the inspection of cladding shows a remarkable fact: depending on the reflectors used, a different performance characterization of the probe must be expected. It seems important for performance demonstration trials - especially those including the underclad area - to use reflector types as close as possible to the real cracks to be detected. For different detection approaches, reflectors representing underclad cracks should have a reduced diffraction at the crack tip areas in order to check their potential to detect the indication based on surface reflections of the ultrasonic waves.
The effect of transcrystallinity in carbon fiber reinforced poly(p-phenylene sulfide (PPS) composites on the apparent shear strength was investigated with the single fiber pull-out test. Transcrystalline zones around the reinforcing fibers do not seem to improve the adhesion level significantly. Neighbor fibers hinder the formation of the transcrystalline zone and a ductile fracture behavior can be observed. However, the apparent strength level is slightly higher for composites containing such reinforcing neighbor fibers compared with single fiber composite samples. During annealing a brittle interface can be formed in the multifiber composite yielding a higher level of the apparent shear strength.
A mathematical model for the description of the overall crystallization of polymers has been developed which separates the pure geometric spreading of the semicrystalline superstructures from the increasing crystallinity inside these entities. The model uses the Avrami theory for the geometric part and a freely optional function for the increasing local crystallinity. The two functions are combined by a mathematical procedure called convolution. The free option of the local crystallinity function enables this model to permit calculation of this function, which is not accessible to direct measurement. Thus with given Avrami parameters and measured values of the time-dependent overall crystallinity, this function of the local crystallinity (secondary crystallization function) can be calculated. The model has been applied to test data produced by computer simulations.
An integral method to calculate the solution of a homogeneous or layered soil due to a harmonic point load is described. An infinite plate at the surface of the soil can be introduced in this integration in wavenumber domain, too. Finite structures on the soil are calculated by a combined finite element and boundary element method, which makes use of the point load solution of the soil. The compliance functions for a vertical point load and some vibration modes are calculated for realistic parameters of the plate and the soil and for a wide range of frequencies. The influence of the stiffness of the soil and the foundation is investigated, showing that the soil mainly affects the low-frequent response whereas the structural properties are more important at higher frequencies. A rigid approximation of flexible plates is only found at low frequencies, if the elastic length is used as the radius of a rigid disk. At higher frequencies, a characteristic behaviour of the flexible plate of approximately is observed, what is in clear contrast to the compliance of rigid foundations. A plate on a visco-elastic support (Winkler soil) shows similar displacements as a plate on a homogeneous half-space, but the maximal stresses between the plate and the soil are considerably smaller which is found to be more realistic for a plate on a layered soil. For practical applications, a normalized diagram and some explicit formulas of the exact and the approximate solutions of an infinite plate on a homogeneous half-space are given, which is a useful model to represent the soil-structure interaction of flexible foundations.
High-power lasers in industrial and R & D applications raise the general problem of reliability and degradation of optical components. A systematic study of nonlinear interaction of various transparent dielectric materials as e.g. glasses, fused silica, and polymers, with laser-pulses in the intensity range of up to 1013 W cm-2 is presented. On the other hand, femtosecond-pulse laser processing in the visible spectral range (300 fs; 620 nm, ~ 2 eV) allows precise microstructuring of transparent dielectrics without disruption of the remnant material. Damage and ablation threshold fluences occur above 1.2 J cm-2 at both silicate glasses and fused silica. Two different photon absorption mechanisms have been observed. The first occurs during the initial laser pulses in the incubation range. There, multiphoton absorption results in moderate energy volume densities. These are sufficient to generate morphological changes and optically active defect sites (colour centres) which provide a much higher absorptivity relevant for the second mechanism. It results in gasification without participation of melt.
A first investigation on the ablation of composite materials like carbon and silicon-carbide reinforced alumo- and borosilicate glasses by 300 fs laser pulses (620 nm) in comparison to experiments with 17 ns pulse excimer laser (308 nm) treatment is presented. In all composites, femtosecond laser scans with a fluence of less than 2 J cm-2 produce well defined cuts with smooth side walls in contrast to the nanosecond laser result where extremely incongruent ablation is observed. Visible lasers should not be applicable because SiC and the glasses are practically transparent. Visible subpicosecond pulses of high intensity in the TW cm-2 range allow multi-photon absorption accompanied by incubation phenomena. The morphology of the groove edges reveal the contrasting ablation thresholds and rates of the fibre and glass materials. The ablation thresholds of the transparent components, i.e. the glass matrices and SiC, are about one order of magnitude greater than that of carbon which is ~ 0.15 J cm-2. Incubation effects are important for the absorption mechanisms in the transparent materials. When a critical number of pulses has not been reached at the SiC-glass composites, only the glass is preferentially ablated, and the fibres remain intact. This is in contrast to the C-glass composites where the ablation behaviour is opposite.