Filtern
Dokumenttyp
- Zeitschriftenartikel (9)
- Vortrag (4)
- Beitrag zu einem Tagungsband (1)
- Posterpräsentation (1)
Sprache
- Englisch (15)
Schlagworte
- Portland cement (15) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (4)
Volumetric changes follow Portland cement hydration reactions: aluminates' hydration is generally expansive, whereas silicates' reaction leads to shrinkage. Determining the volumetric variation at very early ages (i.e., first minutes/hours) presents operational challenges; most standards prescribe the measurement on specimens that are already hardened, while measurements from the fresh state are not standardized. This article reports the first attempt to use in-situ X-ray diffraction (XRD) to measure the early-age volumetric variation of a cementitious paste. For this purpose, a C3A + gypsum paste was assessed for 36 h, measuring its vertical displacement over time through XRD. The results showed that the expansion increased in the first ∼13 h, in line with the ettringite formed up to ∼11 h. In addition, the volumetric expansion agreed well with the heat release in calorimetry. It is concluded that the volumetric variation measurement of cementitious pastes through in-situ XRD is a promising technique, but further studies are needed to make this technique consolidated.
This study uses conventional 87Sr/86Sr and 143Nd/144Nd isotope and interelement ratios of Ca, Sr, K, Mn, Mg and Ti as fingerprints for provenancing ordinary Portland cements (OPC). Herein, the first database of Sr and Nd isotope ratios investigated in OPCs, stemming from 29 cement plants located worldwide, was created. The results show that the Sr isotope ratios of OPCs are higher than those of seawater from the observed geological period. The spread of 143Nd/144Nd in OPCs is not as large as the spread for 87Sr/86Sr isotope ratios. However, the combination of both Sr and Nd isotope ratios provides the potential for distinguishing between cements of different production sites. Most of the OPCs investigated have measurable differences in their 87Sr/86Sr and 143Nd/144Nd isotope ratios, which can be employed as a valuable analytical fingerprinting tool. In the case of equivocal results, divisive hierarchical clustering was employed to help overcome this issue. The construction of geochemical profiles allowed the computing of suitably defined distances between cements and clustering them according to their chemical similarity. By applying this methodology, successful fingerprinting was achieved in 27 out of the 29 ordinary Portland cements that were analysed.
This paper aimed to perform an exploratory literature review, focusing on the aspects of hydration and rheological properties of cementitious composites with açaí fibers. The use of natural fibers as a reinforcement in cementitious matrices has been widely studied, and açaí fiber is a promising option due to its unique characteristics. However, there is still a lack of knowledge regarding the correlation between fiber parameters and the technological properties of composites, which limits the development of new applications, such as 3D printing. The review provided an overview of the main characteristics of açaí fibers and the parameters for their application in cementitious matrices. Alkali treatment with 5% NaOH solution for 1 h shows increased mechanical and physical properties in açaí fibers. Despite the potential advantages of these composites, they pose challenges due to the different fiber surface treatment and interfacial transitions and the processing conditions of the fibers. Although small addition of açaí fibers slightly decreases the cement hydration process, keeping the cross-compatibility index high (>95). To overcome these challenges, it is necessary to evaluate the rheological behavior of cementitious materials with açaí fibers, which has not been reported in the literature. By doing so, it will be possible to optimize the processing conditions and develop new applications, such as additive manufacturing, which has never been explored with açaí fibers.
Binary systems composed of Portland cement (PC) and calcium sulfoaluminate (CSA) cement have stood out for applications requiring high early strengths. Nevertheless, the application of these systems may be limited due to their properties in the fresh state, which requires a better understanding of the rheological behavior of these materials. Thus, this study evaluated the incorporation of different polycarboxylate-based superplasticizer (SP) contents (0.15, 0.20, and 0.25 wt%) on PC and PC-CSA binary cement pastes. Rotational rheometry, isothermal calorimetry, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and nitrogen adsorption and desorption tests to assess the pore size distribution of cement pastes were conducted. While the SP incorporation reduced the dynamic yield stress of PC pastes, it progressively increased the yield stress of PC-CSA systems. The increase in SP content increased the main heat flow peak of PC-CSA pastes, although it did not significantly affect the cumulative heat after 160 h of hydration. FTIR and XRD confirm higher ettringite contents in the binary systems and indicate the presence of carboaluminates phases after 7 d of hydration in both PC and PC-CSA and hemicarboaluminate in PC-CSA pastes. The CSA incorporation reduced the cumulative pore volume by up to 32% compared to PC pastes, while the SP content evaluated did not significantly affect the porosity of PC-CSA pastes.
A thorough characterization of base materials is the prereq- uisite for further research. In this paper, the characterization data of the reference materials (CEM I 42.5 R, limestone pow- der, calcined clay and a mixture of these three components) used in the second funding phase of the priority program 2005 of the German Research Foundation (DFG SPP 2005) are presented under the aspects of chemical and min- eralogical composition as well as physical and chemical properties. The data were collected based on tests performed by up to eleven research groups involved in this cooperative program.
For the construction of hot water storage tanks, ultra high performance concrete proofed to be a suitable building material to ensure water tightness. Common storage tanks build with concrete are designed to endure temperatures up to 90 °C. To increase the energy efficiency however, modern tanks need to withstand temperatures above 100 °C. With increasing temperature and correlating water vapor pressures, the cement must meet new requirements. Thermodynamic modelling is a promising tool for predicting the phase stabilities of minerals in the cement within these temperature and pressure ranges (T/P). Thus, mixture designs can be investigated and optimized with regard to the expected mineral phases in selected T/P-ranges. Additionally, predictions of the long-term material behavior can be derived from thermodynamic data and subsequently the experimental effort can be reduced notably. On the other hand, validation of predictions is needed. The base for the thermodynamic model is a thermodynamic equilibrium and thus, the experimental data for validation should approach the presumed conditions of the equilibrium. This study investigates variable experimental conditions for the hydration of Portland cement at 100 °C to reach a sufficiently progressed development of the phase composition. In case of Portland cement, the highest degree of hydration achievable within a reasonable time span is the most significant parameter. Therefore, Portland cement pastes with w/c ratios from 0.4 to 0.6 and dwell times up to three weeks were examined with powder X-ray diffraction to identify mineral phase changes. At 100 °C and high humidity, Portland cement paste shows the expected mineral phases like portlandite, katoite, and remaining clinker phases. The cement pastes with high water content and long dwell time seem to have the highest degree of hydration, even though the AFm phases stabilize with increasing w/c ratio. A dwell time of two weeks and a w/c ratio of 0.5 was found to provide the mineral composition with the highest degree of hydration including the major phase transitions.
The adaption of the set-up for gas permeability measurements for ultra-high performance concrete
(2022)
In the framework of this project, a steam pressure vessel was to be developed from ultra-high perfor-mance concrete (UHPC) to withstand process temperatures of 200 °C and the respective steam pressure of 15,5 bar. To guarantee the long-term water vapour tightness of the system, the permeability of two UHPC mixtures were tested after long-term cyclic autoclaving. As UPHC shows a high density and therefore low permeability, measurements after the RILEM-Recommendation (TC 116-PCD) reached their detection limit. Therefore, the measurement set-up was adapted to measure the permeability of highly dense UHPC more reliably and quickly. This adaption includes measurements in a higher pres-sure range, the change of sample size thickness and the usage of Ar as a medium compared with the RILEM Recommendation. Additionally, the system was equipped with two pressure sensors and Ar-flowmeters to guarantee a continuous record of the experimental parameters. The new system was tested and evaluated by comparing measurements with the RILEM recommended system. Preliminary results show that the adapted system is capable to provide efficient and reliable results of concrete with low permeability.
A thorough characterization of starting materials is the precondition for further research, especially for cement, which contains various phases and presents quite a complex material for fundamental scientific investigation. In the paper at hand, the characterization data of the reference cement CEM I 42.5 R used within the priority program 2005 of the German Research Foundation (DFG SPP 2005) are presented from the aspects of chemical and mineralogical compositions as well as physical and chemical properties. The data were collected based on tests conducted by nine research groups involved in this cooperative program. For all data received, the mean values and the corresponding errors were calculated. The results shall be used for the ongoing research within the priority program.
Chemical admixtures are widely used to adjust properties of the cementitious mixtures. Different superplasticizers (SP) are typically added to improve the flowability of the fresh cement paste. Their working period is the initial stage of the cement hydration from its beginning until stiffening. Currently, polycarboxylate-based SP (PCE-SP) are the most effective ones. They can act beyond their aimed function causing changes in the hydration course, e. g. retardation effects. The exact mechanisms and influencing factors are still under investigation. However, the occurrence of the retardation effect indicates the involvement of PCE in the hydration reactions. Some observations indicate, that the retardation depends on the type, molecular structure and concentration of PCE, and the presence of other admixtures (stabiliser, ST). These factors influence further the working time of admixture and its amount related efficacy in the flow improvement.
We investigate the cement hydration process in situ in levitated droplets. High resolution synchrotron X-ray diffraction allows gathering temporal course of the hydration reactions. The measurement setup is based on an ultrasonic levitator allowing in situ investigation of the temporal changes of the phase composition in the hydrating cementitious system. Further, the hydration can be followed ab initio avoiding the time loss for the sample preparation and filling in the sample holder. The collected data allows to conclude about the mechanisms of the admixture action and their involvement into the ongoing hydration process.
Chemical admixtures are widely used to adjust properties of the cementitious mixtures. Different superplasticizers (SP) are typically added to improve the flowability of the fresh cement paste. Their working period is the initial stage of the cement hydration from its beginning until stiffening. Currently, polycarboxylate-based SP (PCE-SP) are the most effective ones. They can act beyond their aimed function causing changes in the hydration course, e. g. retardation effects. The exact mechanisms and influencing factors are still under investigation. However, the occurrence of the retardation effect indicates the involvement of PCE in the hydration reactions. Some observations indicate, that the retardation depends on the type, molecular structure and concentration of PCE, and the presence of other admixtures (stabiliser, ST). These factors influence further the working time of admixture and its amount related efficacy in the flow improvement.
We investigate the cement hydration process in situ in levitated droplets. High resolution synchrotron X-ray diffraction allows gathering temporal course of the hydration reactions. The measurement setup is based on an ultrasonic levitator allowing in situ investigation of the temporal changes of the phase composition in the hydrating cementitious system. Further, the hydration can be followed ab initio avoiding the time loss for the sample preparation and filling in the sample holder. The collected data allows to conclude about the mechanisms of the admixture action and their involvement into the ongoing hydration process.