Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (6)
- Zeitschriftenartikel (5)
- Vortrag (2)
- Dissertation (1)
Sprache
- Englisch (14)
Schlagworte
- Polymer optical fiber (14) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (2)
In this thesis, a distributed Brillouin sensor in perfluorinated polymer optical fibers utilizing BOFDA is presented. These commercially available polymer fibers offer beneficial characteristics for sensing applications such as higher break down strain up to 100 %, minimal bending radii below 2 mm, higher sensitivity to temperature and lower sensitivity to strain compared to their silica equivalent.
The chosen wavelength of operation at 1319 nm corresponds to lower fiber propagation loss (< 37 dB/km) compared to other approaches at 1550 nm (150 - 250 dB/km). A 86 m PFGI-POF was successfully measured by BOFDA with spatial resolution of 3.4 m.
The findings related to humidity influences can serve as a basis for future distributed humidity sensors not only limited to stimulated Brillouin backscattering.
The distributed measurement of relative humidity is a sought-after capability for a wide range of applications in civil engineering and structural health monitoring. We show that polymethyl methacrylate (PMMA) optical fi-bers can be employed as a sensor medium to conduct distributed humidity measurement by analyzing Rayleigh backscattering traces obtained by OTDR. We make use of the effect that water penetrates the fiber core and directly influences the local fiber attenuation and Rayleigh backscatter coefficient. We conducted distributed backscattering analysis for two different pulse wavelengths: 500 nm and 650 nm. The 650 nm results are susceptible to both, attenuation changes and backscatter changes, whereas backscatter results at 500 nm are not affected by humidity-induced attenuation and only exhibit a change of Rayleigh backscattered power as a function of humidity. The combined measurement and analysis of both parameters at these two wavelengths has the advantage that cross-sensitivities on backscatter change and attenuation, such as strain and tempera-ture changes, could be separated from the humidity response of the fiber. We present laboratory results for a humidity range between 30% and 90% for both pulse wavelengths: including step responses, humidity cycles and hysteresis analysis. In addition to the attenuation and backscatter coefficient dependence, we also analyze optical runtime changes as a function of humidity. POFs have the advantage that they can be directly embed-ded into materials such as concrete or soil to measure water content or localize water ingress. Standard step-index PMMA POFs can be used as a distributed relative humidity sensor up to 200 m distance.
Solution doping of commercial polymethyl methacrylate (PMMA) polymer optical fibers (POFs) is presented as a novel approach for preparation of custom cladding-doped POFs (CD-POFs). The presented method is based on a solution-mediated diffusion of dopant molecules into the fiber cladding upon soaking of POFs in a methanol-dopant solution. The method was tested on three different commercial POFs using Rhodamine B as a fluorescent dopant. The dynamics of the diffusion process was studied in order to optimize the doping procedure in terms of selection of the most suitable POF, doping time and conditions. Using the optimized procedure, longer segment of fluorescent CD-POF was prepared and its performance was characterized. Fiber’s potential for sensing and illumination applications was demonstrated and discussed. The proposed method represents a simple and cheap way for fabrication of custom, short to medium length CD-POFs with various dopants.
Distributed measurement of humidity is a sought-after capability for various fields of application, especially in the civil engineering and structural health monitoring sectors. This article presents a method for distributed humidity sensing along polymethyl methacrylate (PMMA) polymer optical fibers (POFs) by analyzing wavelength-dependent Rayleigh backscattering and attenuation characteristics at 500 nm and 650 nm wavelengths. Spatially resolved humidity sensing is obtained from backscatter traces of a dual-wavelength optical time domain reflectometer (OTDR). Backscatter dependence, attenuation dependence as well as the fiber length change are characterized as functions of relative humidity. Cross-sensitivity effects are discussed and quantified. The evaluation of the humidity-dependent backscatter effects at the two wavelength measurements allows for distributed and unambiguous measurement of relative humidity. The technique can be readily employed with low-cost standard polymer optical fibers and commercial OTDR devices.
We present the production process and characterization of a fluorescent functionalized elastomeric polymer optical fiber (E-POF) consisting of a covalently linked interface between fiber core and fiber cladding. This all silicone rubber E-POF shows increased temperature stability and can be used for sensing applications. Due to the sophisticated production process surface roughness of the interface of fiber core - fiber cladding are even lower than of the thermoplastic tubing template. Total fiber lengths can be extended by a "chemical splicing" technique, allowing individual tailoring of fibers while maintaining sufficient elasticity under applied mechanical stress.
New sensors for the detection of partial discharges (PDs) in high-voltage (HV) cable accessories are being de-veloped consisting of a fluorescent polymer optical fiber (F-POF) as sensing element. Depending on the fiber material F-POFs can be attached to and even integrated into the translucent silicone rubber insulation of HV cable terminations. As the embedment into the insulation material plays an important role, the sensor should not weaken the dielectric strength of the insulation material and should not be the origin of PD incidents. A sensor consisting of a commercial F-POF has been tested in the high-voltage lab regarding its PD detection ability un-der AC in comparison to a conventional electrical sensor. New silicone rubber F-POF (Si-F-POF) fiber models functionalized with coumarin dyes have been produced. The optical properties of these dye functionalized silox-anes are presented. These potential sensor fibers are highly flexible and might be embeddable at medium to high-voltage level. An additional way to further improve the level of PD light detection is to modify the translucent type of silicone rubber used in HV cable accessories in terms of optical transparency. In this context we present our first results of the optical and mechanical properties of new elastomeric transparent silicone materials specif-ically designed for the application as HV insulation materials in stress cones.
We propose to use focused femtosecond laser pulses to inscribe Scattering damage in the core of polymer optical fibers for interrogation as quasi-distributed sensor points by optical time domain reflectometry.
Fiber bend measurement is demonstrated on off-center inscribed sensor points and absolute temperature measurement is presented by evaluation of the constant backscatter intensities from the inscribed structures relative to temperature-dependent Rayleigh Scattering. Application possibilities and limitations of this new approach are discussed.
We propose a new scheme of Brillouin optical frequency-domain analysis (BOFDA) for distributed fiber-optic strain and temperature sensing, named linear-configured BOFDA (L-BOFDA). In conventional loop-configured BOFDA, light injection into both ends of a fiber under test (FUT) is needed for counter-propagation of pump and probe waves. In contrast, in L-BOFDA, pump and probe waves are injected into the same end of an FUT, and the probe wave Fresnelreflected (or mirror-reflected) at the other end of the FUT is exploited; thus, one-end access is feasible. We show proof-of-concept results of distributed strain measurement in a silica single-mode fiber with L-BOFDA, and discuss the signal-to-noise ratio degradation and the benefit in developing distributed Brillouin sensors based on polymer optical fibers.
Focused femtosecond laser pulses are used to create scattering damage in the core of polymer optical fibers (POF). The resulting structures are investigated regarding morphology by light microscopy and backscattered intensity using optical time domain reflectometry (OTDR). Quasi-distributed optical fiber sensing is proposed by evaluating backscatter changes at the inscribed scatter centers. Application examples for quasi-distributed measurement of fiber bends and temperature are demonstrated.