Filtern
Dokumenttyp
- Vortrag (5)
Sprache
- Englisch (5)
Referierte Publikation
- nein (5)
Schlagworte
- Materials science (5) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (5) (entfernen)
Thermomagnetic materials are a new type of magnetic energy materials, which enable the conversion of low temperature waste heat to electricity by three routes: Thermomagnetic motors, generators and microsystems. Taking our recent work on thermomagnetic generators as a starting point, in this talk we analyse the material requirements for a more energy and economic efficient conversion. We will describe the influence of magnetisation change and heat capacity on thermodynamic efficiency, as well as the consequences of thermal conductivity on power density. Our analysis will allow selecting the best thermomagnetic materials in Ashby plots and illustrate the substantial different properties compared to magnetocaloric materials. Supported by DFG, project FA 453/14)
To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. More than a century ago, thermomagnetic generators were proposed, which are based on a change of magnetization with temperature, switching a magnetic flux, which according to Faraday’s law induces a voltage. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit. A pretzel-like topology of the magnetic circuit with genus =3 improves the performance of thermomagnetic generators by orders of magnitude. We will show that this technique is on its way to becoming competitive with thermoelectrics for energy harvesting near room temperature.
To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit.
Functional materials for energy conversion are important technology drivers needed for the implementation of low carbon energy. Therefore, researchers commonly focus on improving the intrinsic properties of a functional material. However, for applications, the extrinsic properties are at least as important as the intrinsic ones. Consequently, it is important to investigate and understand the external and internal structure of semi-finished products and especially defect dependent properties. The extrinsic properties may change during application and the life cycle of the material as well as through processing and molding steps.
Our studies show how X-ray tomographic (XCT) investigations can contribute to structure investigations in composites and massive samples using the example of magnetic materials for energy conversion. The components are tested non-destructively in 3D in order to localize and characterize cracks, pores, inclusions as well as other defects and their influence on the functional properties and also “in-time” during the life cycle of the material. Exsitu and in-situ experiments performed with non-destructive XCT are predestinated to follow damaging mechanisms of materials under certain load conditions, atmospheres or liquids, e.g. went through several working cycles of a functional material. By combining microtomography with other methods of magnetic and classical material characterization, unique statements about the structure and the functional properties can be made.
From the applications point of view, sometimes complex, three-dimensional geometries are needed to fully exploit the functional properties of the materials, e.g. to ensure a high surface area for heat exchange. Since many functional materials are brittle and difficult to form, shaping is often a big challenge. In principle, additive manufacturing processes offer the possibility to produce complex, porous components from poorly formable alloys.
If all stages of additive manufacturing are accompanied by X-ray tomographic imaging, the process of finding the optimal parameters for material processing can be significantly accelerated.
Based on the quality control of the initial powder material used and also investigations of the shape and arrangement of defects within the molten structure and their relationship with the melting path scanning strategy, Xray tomography has proven to be an ideal tool for additive manufacturing, even for functional materials. Overall, tomographic methods are important tools for the development of functional materials to application maturity.