Filtern
Dokumenttyp
Sprache
- Englisch (4)
Referierte Publikation
- ja (4)
Schlagworte
- Fuel (4) (entfernen)
Organisationseinheit der BAM
Fuel contamination of soils display complex and variable hydrocarbon mixtures with different volatility and toxicity characteristics. A recently suggested headspace procedure for the structure-based quantification of volatile hydrocarbons is evaluated regarding repeatability, reproducibility, and practical robustness. Three aliphatic and three aromatic fractions covering the boiling range between 69 and 216°C were defined as summation parameters by their respective equivalent carbon number ranges. A standard mixture of 35 aliphatic and aromatic hydrocarbons was used for calibration on basis of selected mass fragments specific for the aliphatics and aromatics, respectively. Two standard soils were fortified with the standard mixture or different fuels, respectively, and submitted to the analytical procedure. Limit of detection (LOD) and limit of quantification (LOQ) were for all fractions lower than 0.1 and 0.3 mg/kg, respectively. Analyte recovery was linear up to between 20 and 110 mg hydrocarbons/kg soil depending on the fraction. Hydrocarbon recovery ranged between 80% and 110% depending on the fraction and the repeatability was typically better than 10%. Finally, the impact of extraction solvent variation, column solid-phase polarity, and alternative summation of fractions were investigated. The procedure was applied to liner samples taken from a site contaminated with aviation fuel and its practicability is discussed.
The CCQM-K123 key comparison was organized by the Inorganic Analysis Working Group (IAWG) of CCQM to assess and document the capabilities of the national metrology institutes (NMIs) or the designated institutes (DIs) to measure the mass fractions of sodium, calcium, potassium, magnesium phosphorous and sulfur in biodiesel fuel (BDF). The National Metrology Institute of Japan (NMIJ) and National Institute of Standards and Technology (NIST) acted as the coordinating laboratories.
Results were submitted by 11 NMIs and DIs. The participants used different measurement methods, though most of them used inductively coupled plasma-mass spectrometry (ICP-MS), isotope dilution technique with ICP-MS and inductively coupled plasma-optical emission spectrometry (ICP-OES) with microwave acid digestion.
The material was quite challenging and a number of questions were raised at the IAWG meeting. Concerning S, the variation in S results between participants, particularly those using IDMS methods was discussed at the IAWG meeting. BAM, NIST and NMIJ reviewed their experimental conditions, results and/or uncertainty calculations for IDMS. According to the additional evaluation and investigation, the variances between the revised results became smaller than the original one, the revised results were overlapping between IDMS measurements of S content at the k=2 level. It is not possible to calculate a KCRV with values being modified after submission. It was concluded that this KC does not support S measurements.
Accounting for relative expanded uncertainty, comparability of measurement results for each of Na, Ca, K, Mg and P was successfully demonstrated by the participating NMIs or DIs. It is expected that sodium, calcium, potassium, magnesium and phosphorus at mass fractions greater than approximately 0.1 mg/kg, 0.1 mg/kg, 0.05 mg/kg, 0.05 mg/kg and 0.1 mg/kg respectively in biodiesel fuel and similar matrices (fuels and oils etc.) can be determined by each participant using the same technique(s) employed for this key comparison to achieve similar uncertainties mentioned in the present report. Furthermore, the results of this key comparison can be utilized along with the IAWG core capability approach.
A Memorandum of Understanding (MOU) between the Federal Institute for Materials Research and Testing (BAM) and Argonne National Laboratory (Argonne) was signed in the fall of 2014. Its objectives are to promote cooperation among scientists and specialists at BAM and Argonne and establish a framework for collaboration in the field of advanced technologies associated with the back end of the nuclear fuel cycle. Collaborative activities involving the BAM and Argonne may be implemented through the promotion of joint research activities and scientific workshops and conferences; the exchange of technical information; and visits by scientists, specialists, and graduate, postgraduate, and Ph.D. students. The first Argonne/BAM workshop was held at Argonne in October 2014 to discuss aging management issues related to the long-term dry storage of spent fuel. Major topics for potential collaboration on the extended storage of spent nuclear fuel and its subsequent transportation were identified.
The present paper aims to re-examine the validity of the linear correlation found between AFTLOC, the adiabatic flame temperature at the apex of the flammability range of fuel-air-inert mixtures (where LOC, the Limiting Oxygen Concentration, is measured) and AFTLFL, the adiabatic flame temperature at the lower flammability limit of fuel-air mixtures (LFL). New sets of experimental measurements of LFL and LOC referring to fuel-air mixtures diluted with N2, CO2 and H2O(vap) from trusted literature sources form a comprehensive database for such evaluation. Both the slope and intercept of correlations AFTLOC = a + b*AFTLFL are dependent on the nature of inert gas and on initial temperature. Based on the linear correlation between AFTLOC and AFTLFL, a procedure for calculation of LOC and MIC (Minimum Inert Concentration) of fuel-air-inert mixtures is presented, using measured or calculated LFL of fuel-air mixtures and their corresponding AFT. The method predicts with reasonable accuracy LOC and MIC of fuel-air-inert mixtures (relative deviations ranging between -14 and +17% when calculated and measured LOC and MIC for fuelair-nitrogen and fuel-air-carbon dioxide at ambient initial conditions are examined).