Filtern
Dokumenttyp
- Zeitschriftenartikel (3)
- Posterpräsentation (2)
- Beitrag zu einem Sammelband (1)
- Vortrag (1)
Schlagworte
- Density (7) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Im Rahmen des 2. BAM-Akademie Info-Tages "Nano or not Nano" wurde die OECD TG 124 "Volume Specific Surface Area of Manufactured Nanomaterials" vorgestellt. Der Vortrag beschreibt detailliert das Messverfahren der He-Gaspyknometrie zur Bestimmung der Skelettdichte von Pulvern und geht auf Anwendbarkeit, Besonderheiten bei Nanopulvern und wichtige Einstellparameter für die Messung ein.
The system Na2O.B2O3-SiO2 (NBS) is the basis of many industrial glass applications and therefore one of the most studied systems at all. Glass formation is possible over a wide compositional range, but the system also contains ranges of pronounced phase separation and crystallization tendency. Despite its importance, experimental data are limited to few compositional areas. The general understanding and modelling of glass formation, phase separation, and crystallization in this system would therefore be easier if small step melt series could be studied. The efficient melting of such glass series is now possible with the new robotic glass melting system at the Federal Institute for Materials Research and Testing (BAM, Division Glasses). Using three exemplary joins within this NBS system, the small step changes of glass transition temperature (Tg), crystallization behavior as well as glass density (Roh) was studied. Additionally, experimental Tg and Roh data were compared with their modeled counterparts using SciGlass and a newly developed DFT model, respectively.
One of the crucial characteristics of functionalized thin films is their porosity (i.e., the ratio between the pore volume and the volume of the whole film). Due to the very low amount of material per coated area corresponding to thin films, it is a challenge for analytics to measure the film porosity. In this work, we present an Approach to determine the porosity of thin films by means of electron probe microanalysis (EPMA) either by wavelength-dispersive X-ray spectrometry (WDX) or by energy-dispersive X-ray spectrometry (EDX) with a scanning electron microscope (SEM). The procedure is based on the calculation of the film mass deposition from electron-excited X-ray spectra. The
mass deposition is converted into film density by division of measured film thickness.
Finally, the film porosity is calculated from the measured film density and the density of bulk, nonporous film material. The general applicability of the procedure to determine the
porosity is demonstrated on thin templated mesoporous TiO₂
films, dip-coated on silicon
wafer, with controlled porosity in the range of 15 to 50%. The high accuracy of the mass deposition as determined from X-ray spectra was validated with independent methods (ICP-OES and weighing). Furthermore, for the validation of the porosity results, ellipsometry, interference fringes method (IFM), and focused ion beam (FIB) cross sectioning were employed as independent techniques. Hence, the approach proposed
in the present study is proven to be suited as a new analytical tool for accurate and relatively fast determination of the porosity of thin films.
This work provides accurate experimental (p, rho, T) values for three binary mixtures of methane with helium: (0.95 (amount-of-substance fraction) CH₄+ 0.05 He) and (0.90 CH₄+ 0.10 He) at temperatures of (240, 250, and 260) K and (0.50 CH₄+ 0.50 He) from (240 to 400) K. This work is a continuation of a previous one which reported accurate experimental (p, rho, T) values for the (0.95 CH₄+ 0.05 He) and the (0.90 CH₄+ 0.10 He) binary mixtures over the temperature range from (250 to 400) K. All density measurements were performed by using a single-sinker densimeter with magnetic suspension coupling at pressures up to 20 MPa. Experimental values were compared with the corresponding densities calculated from the GERG-2008 and the AGA8-DC92 equations of state, respectively. Deviations from the GERG-2008 are much larger than from the AGA8-DC92 (up to -6.5%). These deviations increase with decreasing temperature, with increasing pressure, and with increasing helium fraction. In contrast, deviations from the AGA8-DC92 are within the 0.5% band. The experimental values were also used to calculate the second and the third virial coefficients, B(T,x) and C(T,x), as well as the second interaction virial coefficient B12(T) for this mixture.
Experimental characterization of the thermodynamic behavior of multicomponent gas mixtures of accurately known composition is of great importance for testing the current reference equation of state for natural gases and related mixtures, GERG-2008. Natural gas composition may change considerably due to the diversity of origins, or the possibility to incorporate hydrogen, biogas or other non-conventional energy gases.
Thus, the Consultative Committee for Amount of Substance: Metrology in Chemistry and Biology (CCQM) of the Bureau International des Poids et Mesures (BIPM) launched a key comparison on primary standard mixtures for natural gases of this particular characteristics. One mixture is a hydrogen-enriched natural gas mixture (13 components, x(H2) = 0.03) with low calorific value to facilitate support to power-to-gas applications, which often involve blending hydrogen with natural gas. The other mixture resembles a typical liquefied natural gas (“LNG”, 9 components) with high calorific value.
The use of alternative base oils, like esters or polyglycols, with more intrinsic properties for the lubrication of automobile engines has a potential for ecological and technical advantages. Being in competition with hydrocarbon-based formulations, detailed knowledge of several thermophysical and viscometric properties as well as tribological properties over a large temperature range are required (mapping). The tested polymer-free polyglycols and ester-based formulations displayed no visible tribological weaknesses regarding wear resistance and EP-behavior as well as offering significant advantages in order to meet metal- and ash-free and bio-no-tox criteria. Especially the formulated polyglycols without friction modifiers also showed an intrinsic retention of low coefficients of friction and a hydrodynamic film forming behavior comparable to hydrocarbon-based factory-fill oils. The wear resistance and EP-behavior of low-additivated polyglycols, but also of esters, can be enhanced by means of triboactive materials. Lubricious oxides or triboactive materials and polar base oils, or a combination thereof, may substitute the EP and AW properties realized by the additives, thus enabling long drains and responding to eco-tox or bio-no-tox requirements as well as restrictions from the chemical box.