Filtern
Dokumenttyp
- Zeitschriftenartikel (6)
- Vortrag (1)
Sprache
- Englisch (7)
Schlagworte
- Bismuth (7) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Formation Mechanism of a Nano-Ring of Bismuth Cations and Mono-Lacunary Keggin-Type Phosphomolybdate
(2022)
A new hetero-bimetallic polyoxometalate (POM) nano-ring was synthesized in a one-pot procedure. The structure consists of tetrameric units containing four bismuth-substituted monolacunary Keggin anions including distorted [BiO8] cubes. The nano-ring is formed via self-assembly from metal precursors in aqueous acidic medium. The compound (NH4)16[(BiPMo11O39)4] ⋅ 22 H2O; (P4Bi4Mo44) was characterized by single-crystal X-ray diffraction, extended X-ray absorption fine structure spectroscopy (EXAFS), Raman spectroscopy, matrix-assisted laser desorption/ionisation-time of flight mass spectrometry (MALDI-TOF), and thermogravimetry/differential scanning calorimetry mass spectrometry (TG-DSC-MS). The formation of the nano-ring in solution was studied by time-resolved in situ small- and wide-angle X-ray scattering (SAXS/WAXS) and in situ EXAFS measurements at the Mo−K and the Bi−L3 edge indicating a two-step process consisting of condensation of Mo-anions and formation of Bi−Mo-units followed by a rapid self-assembly to yield the final tetrameric ring structure.
The catalytic potential of bismuth subsalicylate (BiSub), a commercial drug, for ring-opening polymerization (ROP) of L-lactide was explored by variation of co-catalyst and polymerization time. Various monofunctional phenols or carboxylic acids, aromatic ortho-hydroxy acids and diphenols were examined as potential co-catalysts. 2,2´-Dihydroxybiphenyl proved to be the most successful co-catalyst yielding weight average molecular weights (uncorrected Mw values up to 185 000) after optimization of reaction time and temperature. Prolonged heating (>1-2h) depending on catalyst concentration) caused thermal degradation. In polymerization experiments with various commercial Bi(III) salts a better alternative to BiSub was not found. By means of matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrometry a couple of unusual and unexpected transesterification reactions were discovered. Finally, the effectiveness of several antioxidants and potential catalyst poisons was explored, and triphenylphosphine was found to be an effective catalyst poison.
The frictional response of molybdenum bis(C11-14 branched and linear alkyl) carbamodithioate oxo thioxo complex (Mo-dttc) versus bismuth dimethyldithiocarbamate (Bi-dtc) and bismuth dodecylbenzene Sulfonate (Bi-ddbsa) slip-rolling under mixed/boundary lubrication (T=120°C, n=10 millions of cycles, P0max=2.25 GPa) in PAO-based formulation against three different steel alloys were compared.
The growing challenges of environmental purification by solar photocatalysis, precious-metal-free catalysis, and photocurrent generation in photovoltaic cells receive the utmost global attention. Here we demonstrate a one-pot, green chemical synthesis of a new stable heterostructured, ecofriendly, multifunctional microcomposite that consists of α-Bi2O3 microneedles intercalated with anchored graphene oxide (GO) microsheets (1.0 wt?%) for the above-mentioned applications on a large economical scale. The bare α-Bi2O3 microneedles display two times better photocatalytic activities than commercial TiO2 (Degussa-P25), whereas the GO-hybridized composite exhibits approximately four to six times enhanced photocatalytic activities than the neat TiO2 photocatalyst in the degradation of colored aromatic organic dyes (crystal violet and rhodamine 6G) under visible-light irradiation (300 W tungsten lamp). The highly efficient activity is associated with the strong surface adsorption ability of GO for aromatic dye molecules, the high carrier acceptability, and the efficient electron–hole pair separation in Bi2O3 by individual adjoining GO sheets. The introduction of Ag nanoparticles (2.0 wt?%) further enhances the photocatalytic performance of the composite over eightfold because of a plasmon-induced electron-transfer process from Ag nanoparticles through the GO sheets into the conduction band of Bi2O3. The new composites are also catalytically active and catalyze the reduction of 4-nitrophenol to 4-aminophenol in the presence of borohydride ions. Photoanodes assembled from GO/α-Bi2O3 and Ag/GO/α-Bi2O3 composites display an improved photocurrent response (power conversion efficiency ~20?% higher) over those prepared without GO in dye-sensitized solar cells.
A unique direct electrodeposition technique involving very high current densities, high voltages and high electrolyte concentrations is applied for highly selective mass synthesis of stable, isolable, surfactant-free, single-crystalline Bi hexagons on a Cu wire at room temperature. A formation mechanism of the hexagons is proposed. The morphology, phase purity, and crystallinity of the material are well characterized by FESEM, AFM, TEM, SAED, EDX, XRD, and Raman spectroscopy. The thermal stability of the material under intense electron beam and intense laser light irradiation is studied. The chemical stability of elemental Bi in nitric acid shows different dissolution rates for different morphologies. This effect enables a second way for the selective fabrication of Bi hexagons. Bi hexagons can be oxidized exclusively to α-Bi2O3 hexagons. The Bi hexagons are found to be promising for thermoelectric applications. They are also catalytically active, inducing the reduction of 4-nitrophenol to 4-aminophenol. This electrodeposition methodology has also been demonstrated to be applicable for synthesis of bismuth-based bimetallic hybrid composites for advanced applications.
εCL was polymerized using the triflates of lanthanum, samarium, magnesium, aluminum, scandium, and bismuth as catalysts. Bismuth triflate proved to be extraordinarily reactive, and catalyzed polymerizations of εCL even at 20 °C. Adding DTBMP reduced the polymerization rate only slightly. Furthermore, no evidence of a cationic mechanism was found by end‐group analyses. Polymerization at 20 °C either in bulk or in solution only yielded polyesters of low or medium molecular weights. Yet addition of alcohols allowed for a proper control of molecular weight and end‐groups. Additionally, low catalyst concentrations and low temperature resulted in narrow molecular weight distributions and polylactones almost free of cyclic compounds.