The suitability of an Al2O3 coating for corrosion protection on X20Cr13 was evaluated in various artificial geothermal brines, focusing on the influence of different pH (4, 6 and 8) and their chemical compositions on the coating properties. All experiments were performed in the laboratory using autoclaves at 150 ◦C and 1 MPa in deaerated condition for 1 and 7 days. Results showed that the pH of geothermal waters is the most detrimental factor in the transformation of ɣ-Al2O3 and its protective abilities. Delaminations were found in the Coating exposed to geothermal brines with pH 4. FTIR spectra indicated a transformation of ɣ-Al2O3 to boehmite AlOOH after exposure to pH 4 and 6, and bayerite Al(OH)3 was formed after exposure to pH 8. Different Crystal structures of the hydrated Al2O3 also contribute to the stability of the coatings, observed by the SEM- EDX of the surface and cross-section of coatings. This study indicated that ɣ-Al2O3 sol-gel coating presents a promising aspect of corrosion protection in geothermal environment with a neutral pH.
Al2O3 has been widely used as a coating in industrial applications due to its excellent chemical and thermal resistance. Considering high temperatures and aggressive mediums exist in geothermal systems, Al2O3 can be a potential coating candidate to protect steels in geothermal applications. In this study, γ-Al2O3 was used as a coating on martensitic steels by applying AlOOH sol followed by a heat treatment at 600 °C. To evaluate the coating application process, one-, two-, and three-layer coatings were tested in the artificial North German Basin (NGB), containing 166 g/L Cl−, at 150 °C and 1 MPa for 168 h. To reveal the stability of the Al2O3 coating in NGB solution, three-layer coatings were used in exposure tests for 24, 168, 672, and 1296 h, followed by surface and cross-section characterization. SEM images show that the Al2O3 coating was stable up to 1296 h of exposure, where the outer layer mostly transformed into boehmite AlOOH with needle-like crystals dominating the surface. Closer analysis of cross-sections showed that the interface between each layer was affected in long-term exposure tests, which caused local delamination after 168 h of exposure. In separate experiments, electrochemical impedance spectroscopy (EIS) was performed at 150 °C to evaluate the changes of coatings within the first 24 h. Results showed that the most significant decrease in the impedance is within 6 h, which can be associated with the electrolyte penetration through the coating, followed by the formation of AlOOH. Here, results of both short-term EIS measurements (up to 24 h) and long-term exposure tests (up to 1296 h) are discussed.
Silicon surface passivation with atomic layer deposited (ALD) thin films has gained more and more interest in the PV community in recent years. With ALD good film quality, accurate thickness control and conformity are reached. Furthermore, ALD is capable of coating difficult substrates such as nanostructured surfaces with the same accuracy as flat surfaces. A variety of materials such as Al2O3, TiO2 and HfO2 demonstrate good surface passivation quality both for front and rear surface of silicon solar cells. In addition of providing good surface passivation, thin films with high refractive index e.g. HfO2, TiO2 and AlN can act simultaneously as antireflection coatings when applied on the front surface of the device. Hence, ALD thin films can reduce both electrical and reflective losses in solar cells.
Thorough investigation of the optical properties of these layers is crucial for several reasons related to their production and use. Optical measurements provide a fast, easy, non-destructive, and in situ capable approach to quality assurance for photovoltaic devices. As the function of the final device is optical, optimisation of the device performance relies strongly on the knowledge of the wide-range dielectric function of the thin layers. In this contribution, we determined the optical constants of ALD generated layers of AlN, Al2O3, TiO2, and HfO2 in a wide spectral range covering the near ultraviolet and the mid-infrared regions by means of spectroscopic ellipsometry. By combining data from a UV-Vis-NIR ellipsometer (Woollam M2000DI) and an FTIR ellipsometer (Sentech Sendira), we can determine the optical constants alongside with the layer thicknesses from one large set of spectroscopic measurements. We consider this a contribution to the metrological treatment of stratified and structured thin films in the optical range by polarisation-sensitive measurement methods.
The investigation of iron-doped AlO(OH)/Al2O3 systems revealed that the combined employment of Mössbauer and ESR spectroscopies together with thermal analysis yields meaningful data with complementary information. This mutual complementarity is based on the coexistence of Fe point defects with the corresponding aggregated FeOx species which has been observed even for very low Fe concentrations. Competing redox processes between the dopant, the AlOx matrix, and the gas atmosphere during the thermal treatment enable the generation of solid phases exhibiting specific chemical properties. The entire reaction process is influenced by a specific mechanical and thermal pre-treatment that affects predominantly oxydative processes in the matrix. A protecting influence of the matrix preventing further reductive attack of the Fe3+ Fe2+ ions by hydrogen has been established.
Hochtemperaturtribologie
(2010)
The transformation of doped or seeded pseudoboehmite to corundum was studied by combining thermal analysis, X-ray diffraction, transmission electron microscopy, and electron paramagnetic resonance spectroscopy. The temperature of phase transformation to corundum was lowered by about 130 °C when Fe3+ or corundum seeds were added to the sols. Action of Fe3+ ions depends on the actual degree of thermally induced transformation of pseudoboehmite via transition aluminas to corundum and the ability of these alumina phases to incorporate Fe3+ ions. These ions tend to aggregate with increasing iron concentration of the alumina phases and can work as nucleation centers. Small (not, vert, similar20 nm) corundum particles act as active nucleation sites whereas larger grains (200400 nm) also present in the samples are less effective. For the first time trapping and stabilization of NO2 molecules in transition aluminas formed by a solgel route was shown.
To validate the European standard ENV 843-4 for hardness measurements on ceramics, three classes of ceramic materials, silicon nitride, silicon carbide, and aluminium oxide, involving 19 ceramics in total, were tested using the traditional techniques Vickers (HV1), Knoop (HK2), and superficial Rockwell (HR45N). The use of new ceramic reference blocks certified according to the standards ISO 4547 and ISO 6507-1 for metallic materials was studied. If the hardness response of the tested materials does not involve chipping and cracking the application of high hardness reference blocks for training users to obtain hardness values comparable with the certified HV1 and HK2 values improves the reproducibility from about 10% to 1 to 3%. The scatter between the laboratories is similar to the scatter within the laboratories. The measurement of the indentation geometry on typical commercial ceramic materials can be made only with higher scatter and reduced reproducibility compared with typical metallic materials, which is caused by the stochastic indentation response. For such materials involving chipping and cracking (for instance SiC), the application of reference blocks with well-shaped indentations does not provide improved comparability of results between the laboratories. The actual indentation response of the ceramic material tested must be considered before selecting the appropriate hardness technique and test force. There is no significant difference between the abilities of the hardness techniques HV1, HK2, and HR45N to discriminate sensitively between materials of closely similar properties.
The standard for advanced technical ceramics ENV 843-4 of 1995 (Vickers, Knoop and Rockwell superficial hardness tests) was validated within the framework of the CERANORM EC-project. The paper reports on depth sensing hardness measurements done for comparison with the other hardness tests. The instrumented indentation test is a modern technique (recent issue ISO/DIS 14577) that has the potential to take into account the specific response of materials in a much better way. An evaluation has been made to establish whether the instrumented hardness technique is a appropriate method for advanced technical ceramics and offers potential for additional applications.