Filtern
Dokumenttyp
- Zeitschriftenartikel (6)
- Beitrag zu einem Tagungsband (3)
- Vortrag (3)
- Posterpräsentation (1)
Schlagworte
- Additives (13) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (3)
Laser-induced periodic surface structures (LIPSS, ripples) with ~500–700 nm period were produced on titanium alloy (Ti6Al4V) surfaces upon scan processing in air by a Ti:sapphire femtosecond laser. The tribological performance of the surfaces were qualified in linear reciprocating sliding tribological tests against balls made of different materials using different oilbased lubricants. Extending our previous work, we studied the admixture of the additive 2-ethylhexyl-zinc-dithiophosphate to a base oil containing only anti-oxidants and temperature stabilizers. The presence of this additive along with the variation of the chemical composition of the counterbodies allows us to explore the synergy of the additive with the laseroxidized nanostructures.
In the state-of-the-art technology, the impact of additives on friction and wear is evaluated in recipes with fixed concentrations. For the development of formulations it is desirable to determine the lowest effective concentration or the concentration at which failure was initiated or excessive wear began. Through a new development of the SRV® machine it is now possible to change the lubricant composition of a test specimen in a reproducible manner, in sub-pro Mill steps during the SRV® testing. This technology is used in the present article to define the optimum additive concentration with regard to wear and friction in a system of base oil and additive. Exemplary selected base oil and additive variants are tested here. The load parameters during testing are selected in such a way that they correspond to later application. The new data acquisition capabilities enable new possibilities for optimizing lubricant formulations in practice-oriented model-tribometer tests. “Cliff“ testing aims to identify in engine or gear tests the induction time or off-set point (“cliff“) after which wear and friction increased of failure occurred. Explanations for friction and wear increased as well as failures, which occurred during engine tests, can be derived from SRV® testing of oil samples taken or collected at different engine test times and correlating these with their friction, wear and EP data in respect to depleting curves for specific additives or other oil properties. A “cause-root” analysis is done by plotting SRV® data versus functional properties. The collected oil samples must be fully SRV® tested and chemically analyzed.
After several months of operation, many photovoltaic (PV) modules develop a discolouration defect called snail trails which appear as irregular dark traces across the cells. These traces are caused by silver nanoparticles accumulating within the encapsulation foil directly above the grid finger. In this work we systematically investigate combinations of encapsulation and back-sheet foils with respect to their susceptibility for snail trails. We can show that certain additive compositions within the encapsulation and back sheet foils are critical for the formation of the discolouring silver nanoparticles. We suggest a reaction model explaining the formation of snail trails from a chemical point of view. This fundamental understanding allows the rapid testing of foils for their snail trail sensitivity as well as the special design of resistant foils.
The dilution of biogenic fuels into lubricating engine oils often leads to a shortening of the recommended oil drains (between 30% and 60%) and an increase in wear. The large number of overlapping and influencing factors, of which dilution and polymerization of fuel components in the engine oil are emphasised, makes it difficult to find a uniform solution to prevent failures in the various applications.
Insofar single solutions for the different types of biofuels are needed. The contribution of base oil chemistry and additives as well as triboactive materials is featured to deal with the adverse effects of biofuels. In the frame of the European Commission (EC)-funded project 'cleanengine', tentative engine oils based on esters with a content of renewables and polyglycols are formulated to increase the lubricant's tolerance in engines fuelled with biofuel-based blends, with the aim of ensuring required lubricating and wear protection performance while keeping oil drain intervals unchanged.
The present paper focuses on four-stroke diesel applications, fuelled by biodiesel (fatty acid methyl ester — FAME) as well as by rapeseed oil and Jatropha oil (pure vegetable oils, triglycerides), together with relevant blends of those biofuels and conventional diesel fuel.
This paper screens the functional profile (in particular rheological, toxicological, bio-compatibility, tribological and biofuels affinity) of lube families with respect to biofuel contamination. Moreover, this is followed by the contributions of piston ring and liner materials as well as thin film coatings.