Filtern
Dokumenttyp
- Vortrag (2)
- Zeitschriftenartikel (1)
- Beitrag zu einem Tagungsband (1)
- Posterpräsentation (1)
Referierte Publikation
- nein (5)
Schlagworte
- Überdruckverfahren (5) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (2)
Derzeit existieren für Gefahrgutverpackungen in den internationalen Gefahrgutvorschriften keine Festlegungen für quantitative Grenzleckageraten, die sich an Sicherheitsbetrachtungen während der Beförderung orientieren. Für die Dichtheitsprüfung im Rahmen der Bauartzulassung von Gefahrgutverpackungen für flüssige Füllgüter ist das Standardprüfverfahren das Eintauchverfahren in Wasser („Bubble Test“). Hierbei handelt es sich um ein lokalisierendes Prüfverfahren. Seine Anwendung lässt keine quantitative Aussage darüber zu, ob unter Beförderungsbedingungen aufgrund von strömungsbedingter Stofffreisetzung durch Leckstellen der Gefahrgutverpackungen die Gefahr der Bildung einer explosionsfähigen Atmosphäre besteht. Ziel der vorliegenden Untersuchungen ist daher, zunächst quantitative Dichtheitsanforderungen an Gefahrgutverpackungen im Hinblick
auf die Entstehung explosionsfähiger Dampf-Luft-Gemische während des
Transports zu entwickeln. Im Anschluss werden strömungsbedingte Leckageraten der Verschlüsse verschiedener Bauarten von Gefahrgutverpackungen gemessen. Der Vergleich der Messwerte mit den berechneten Grenzwerten ermöglicht die Einschätzung hinsichtlich der Bildung einer explosionsfähigen Atmosphäre. Dieser quantitative Ansatz zur Beurteilung der Dichtheit ist für Gefahrgutverpackungen derzeit noch nicht etabliert.
Die quantitative Leckageratenmessung der Gefahrgutverpackungen wird mit dem Überdruckverfahren mit Ansammlung (Akkumulationsverfahren) unter Verwendung von Helium als Prüfgas vorgenommen. Zusätzlich erfolgt die Detektion weiterer potentieller Leckstellen außerhalb des Verschlussbereiches mit dem Schnüffelverfahren. Bei allen untersuchten Bauarten, mit Ausnahme des 6 L-Feinstblechkanisters, ist der Verschluss die einzige systematische Leckstelle der Verpackung. Die Messung der Helium-Leckageraten und der anschließende Vergleich mit den berechneten Helium-Grenzleckageraten zeigt, dass folgende Bauarten hinsichtlich des Erreichens der unteren Explosionsgrenze (UEG) durch eine Leckageströmung als kritisch einzuschätzen sind: Kunststoffverpackungen mit Schraubverschlüssen mit Flachdichtung, wenn bei diesen bestimmte Schädigungsmuster im Verschlussbereich vorliegen; Feinstblechkanister, da bei ihnen nicht nur der Verschlussbereich eine Leckstelle darstellt; Kunststoffverpackungen mit Schraubverschlüssen mit Flachdichtung, wenn diese auch für Füllgüter der Verpackungsgruppe I zugelassen sind. Als Konsequenz sollten bei diesen kritischen Bauarten entweder Modifikationen in Bezug auf die Verpackung selbst oder auf die Transportbedingungen im Frachtcontainer vorgenommen werden.
Es werden die Ergebnisse von Leckageratenmessungen an den Verschlüssen von Gefahrgutverpackungen unterschiedlicher Bauarten vorgestellt. Die Prüfungen wurden mit dem Überdruckverfahren mit Ansammlung unter Verwendung des Prüfgases Helium vorgenommen. Die gemessenen Deckelleckageraten zeigen Größenordnungsunteschiede von mehreren Zehnerpotenzen. Durch einen Vergleich mit berechneten Grenzwerten lässt sich die Indentifizierung kritischer Bauarten vornehmen.
The International Dangerous Goods Regulations prescribe the immersion under water method (“bubble test”) as standard method for the leakproofness test of dangerous goods packagings. But this test procedure acts as a test method for leak localisation, not for quantitative leakage rates measurement. Additionally, the sensitivity in detecting leaks of small diameters is restricted, depending on the test liquid and the test pressure. The bubble test is not suitable for a comparison with quantitative limit leakage rates based on realistic transport conditions. This is especially important when estimating the risk of the formation of an explosive atmosphere during the intercontinental carriage of dangerous goods packagings in freight containers. To compare measured leakage rates with limit leakage rates, a quantitative leak testing procedure is required. Therefore a new approach for dangerous goods packagings is implemented: The pressure technique by accumulation using Helium as a tracer gas. This work presents the test equipment necessary for the quantitative measurement of Helium leakage rates through closures of different kinds of dangerous goods packagings. The essential steps to achieve good repeatable results are: A controlled Helium filling process to reach a defined test pressure in the test sample, a sufficient homogenisation of the Helium-air-mixture inside the test sample and the ensuring of a constant pressure level of the test sample during the test. The Helium loss rate of the accumulation chamber has to be measured separately to receive a correction factor for the measured leakage rates. Different constructional measures are introduced to prevent a disturbing influence of the Helium leakage rate of the filling valves on the measurement results. Methods to estimate the disturbing effect of Helium permeation through permeable parts of the test sample are also presented. As a supporting method for the experimental investigations the Helium sniffer test can be applied. This practical application-oriented advice can enable other users to establish a pressure technique by accumulation for their own technical field.
Abstract. The International Dangerous Goods Regulations prescribe the immersion under water method (“bubble test”) as standard method for the leakproofness test of dangerous goods packagings. But this test procedure acts as a test method for leak localisation, not for quantitative leakage rates measurement. Additionally, the sensitivity in detecting leaks of small diameters is restricted, depending on the test liquid and the test pressure. The bubble test is not suitable for a comparison with quantitative limit leakage rates based on realistic transport conditions. This is especially important when estimating the risk of the formation of an explosive atmosphere during the intercontinental carriage of dangerous goods packagings in freight containers.
To compare measured leakage rates with limit leakage rates, a quantitative leak testing procedure is required. Therefore a new approach for dangerous goods packagings is implemented: The pressure technique by accumulation using Helium as a tracer gas.
This work presents the test equipment necessary for the quantitative measurement of Helium leakage rates through closures of different kinds of dangerous goods packagings. The essential steps to achieve good repeatable results are: A controlled Helium filling process to reach a defined test pressure in the test sample, a sufficient homogenisation of the Helium-air-mixture inside the test sample and the ensuring of a constant pressure level of the test sample during the test. The Helium loss rate of the accumulation chamber has to be measured separately to receive a correction factor for the measured leakage rates. Different constructional measures are introduced to prevent a disturbing influence of the Helium leakage rate of the filling valves on the measurement results. Methods to estimate the disturbing effect of Helium permeation through permeable parts of the test sample are also presented. As a supporting method for the experimental investigations the Helium sniffer test can be applied.
This practical application-oriented advice can enable other users to establish a pressure technique by accumulation for their own technical field.
The International Dangerous Goods Regulations prescribe the immersion under water method (“bubble test”) as standard method for the leakproofness test of dangerous goods packagings. But this test procedure acts as a test method for leak localisation, not for quantitative leakage rates measurement. Additionally, the sensitivity in detecting leaks of small diameters is restricted, depending on the test liquid and the test pressure. The bubble test is not suitable for a comparison with quantitative limit leakage rates based on realistic transport conditions. This is especially important when estimating the risk of the formation of an explosive atmosphere during the intercontinental carriage of dangerous goods packagings in freight containers.
To compare measured leakage rates with limit leakage rates, a quantitative leak testing procedure is required. Therefore a new approach for dangerous goods packagings is implemented: The pressure technique by accumulation using Helium as a tracer gas.
This work presents the test equipment necessary for the quantitative measurement of Helium leakage rates through closures of different kinds of dangerous goods packagings. The essential steps to achieve good repeatable results are: A controlled Helium filling process to reach a defined test pressure in the test sample, a sufficient homogenisation of the Helium-air-mixture inside the test sample and the ensuring of a constant pressure level of the test sample during the test. The Helium loss rate of the accumulation chamber has to be measured separately to receive a correction factor for the measured leakage rates. Different constructional measures are introduced to prevent a disturbing influence of the Helium leakage rate of the filling valves on the measurement results. Methods to estimate the disturbing effect of Helium permeation through permeable parts of the test sample are also presented. As a supporting method for the experimental investigations the Helium sniffer test can be applied. This practical application-oriented advice can enable other users to establish a pressure technique by accumulation for their own technical field.