Filtern
Erscheinungsjahr
- 2016 (5) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (5) (entfernen)
Sprache
- Englisch (5)
Referierte Publikation
- ja (5)
Schlagworte
- NDT (3)
- On-site inspection (2)
- Energy dissipation (1)
- Energy sensor (1)
- FEM (1)
- Flash lamp (1)
- Flash thermography (1)
- GFRP (1)
- Infrared imaging (1)
- Long-term experiment (1)
- Metals (1)
- Meteorological influence (1)
- Non-destructive testing (1)
- Nondestructive testing (1)
- Numerical simulation (1)
- Phase measurement (1)
- Polymers (1)
- Solar excitation (1)
- Structural health monitoring (1)
- Thermal imaging (1)
- Thermographic inspection (1)
- Wind turbine rotor blade (1)
Comparison of quantitative defect characterization using pulse-phase and lock-in thermography
(2016)
Using optical excitation sources for active thermography enables a contactless, remote, and non-destructive testing of materials and structures. Currently, two kinds of temporal excitation techniques have been established: pulse or flash excitation, usingmostly flash lamps; and periodic or lock-in excitation, using halogen lamps, LED, or laser arrays. From the experimental point of view, both techniques have their advantages and disadvantages. Concerning the comparison of the testing results of both techniques, only very few studies have been performed in the past. In this contribution, the phase values obtained at flat bottom holes in steel and CFRP and the spatial resolution measured at crossed notches in steel using flash and lock-in excitation are compared quantitatively.
Comparison of concepts for a point-shaped energy density detector after flash lamp excitation
(2016)
The paper describes investigations and Research work in order to develop a simple sensor for the quantification of spectral broadband energy Dissipation of flash lamps at any point in space. Such Flash lamps are often used as energy source during active thermography testing (TT). Here, the temperature transient of the sensor surface has to be recorded by the infrared camera that is already present. During the following data evaluation, the energy input into the investigated specimen can be determined. Two opposite concepts were considered: thermal thick and thermal thin probes. The direct comparison shows advantages for thermal thick probes based on the physics of thermal balance processes.
Recurrent non-destructive testing inspections are necessary to prevent damages in wind turbine rotor blades, but so far, there is no established method that detects defects in blades from greater distances – although this becomes increasingly important in the context of hardly accessible offshore wind parks.
Thermography is a promising method for detecting subsurface defects, but various challenges arise when this method is applied on-site to turbine blades in operation. Disturbing influences from the environment easily lead to a misinterpretation of thermograms (i.e. thermographic images), such as thermal signatures caused by reflections, dirt and other superficial inhomogeneities.
This study explores several problems and effects that arise, when (rotating) blades are monitored with thermography.
It will then be demonstrated that a meaningful defect inspection in this scenario is essentially restricted to a procedure following three steps: Firstly, calculating the so-called difference thermograms of all blade pairs for eliminating disturbing reflections. Secondly, identifying potentially relevant signals, which are associated neither with structural features nor with dynamical effects, and the identification of these signals’ allocations (through comparison of all difference thermograms with each other). And thirdly, comparing these signals with (processed) photos for excluding incorrect indications by surface effects. Unlike common thermographic analysis methods, which typically only include an aspect of this procedure, the composition presented in this contribution constitutes an advanced technique for minimizing disturbing influences in thermograms.
The proposed thermographic technique enables the detection of potential subsurface defects within rotating rotor blades from greater distances – such as from the ground, air crafts or vessels.
The present study continues the work described in part I of this paper in evaluating a longterm-experiment, where a rotor blade segment of a wind turbine is exposed to the elements and thereby monitored with passive thermography. First, it is investigated whether subsurface features in rotor blades – mainly made of GFRP – can generally be detected with thermography from greater distances under favorable conditions. The suitability of the sun for acting as a heat source in applying active thermography has been tested in the previous study. In this study, the climatic influence on thermographic measurement is evaluated. It is demonstrated that there are favorable and unfavorable circumstances for imaging thermal contrasts which reflect inner structures and other subsurface features like potential defects. It turns out that solar radiation serves as a very effective heat source, but not at all times of day. Other environmental influences such as diurnal temperature variations also create temperature contrasts that permit conclusions on subsurface features. Particular scenarios are reconstructed with FEM-simulations in order to gain deeper insight into the driving mechanisms that produce the observed thermal contrasts. These investigations may help planning useful outdoor operations for inspecting rotor blades with thermography.
This study evaluates whether subsurface features in rotor blades, mainly made of Glass Fibre Reinforced Plastics (GFRP), can generally be detected with ‘‘solar thermography”. First, the suitability of the sun is tested for acting as a heat source for applying active thermography on a 30 mm thick GFRP test specimen. Second, a defective rotor blade segment is inspected outdoors under ideal natural conditions using the sun as excitation source. Additionally, numerical FEM-simulations are performed and the comparability between experiment and simulation is evaluated for outdoor measurements.