Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (38) (entfernen)
Schlagworte
- OTDR (4)
- Strain sensor (4)
- Temperature sensor (4)
- Composite structures (3)
- Distributed acoustic sensing (3)
- Distributed fiber sensing (3)
- Distributed fibre optic sensors (3)
- Fibre optic sensor (3)
- Gamma radiation (3)
- Long period grating (3)
Organisationseinheit der BAM
Technical textiles with embedded fibre optic sensors habe been developed for the purposes of the structural health monitoring in geotechnical and civil engineering as well as for healthcare monitoring in the medical sector. The paper shows selected examples of using such sensor-based smart textiles for different applications.
Structural Health Monitoring of composite materials gains in importance with the increasing use of Composite structures for safety-related applications, e.g. in aerospace. Because of the material properties of composites, defects often occur inside the structures and raise the demand for integrated sensors. The advantages of optical fibres predestine them not only for the surface-application on composite structures but also for the Integration into composite structures. Even without quasi-distributed sensors such as FBGs or LPGs, the optical fibre itself can be used to measure the structure and occurring events over the entire fibre length by distributed sensing techniques. This paper presents the surface-application of polyimide coated silica optical fibres onto PEEK specimens and the integration of copper and polyimide coated silica optical fibres into an AS-4/PEEK Composite to be used as distributed fibre optic sensors for SHM. Results from distributed measurements by optical backscatter reflectometry based on Rayleigh backscattering are shown.
In this work, the potential of fiber Bragg gratings (FBGs) in low-loss perfluorinated polymer optical fibers (PF-POFs) is explored. The FBG is femtosecond-inscribed in a commercial multi-mode (MM) PF-POF based on Cytop® polymer. Femtosecond inscription leads to creation of a highly saturated grating with a number of higher order reflection Peaks visible throughout the visible and near-infrared spectral region. For 2 mm long FBG having a pitch of 2.2895 μm, a total of nine higher-order MM reflection bands are visible spanning from 1548 nm (4th order) to 520 nm (12th order). Strain sensitivity was measured for 6 peak bands in 500-900 nm region, where relatively low cost CCD based spectrometers and broadband LEDs are available. Strain sensitivity increases almost linearly with increasing initial peak wavelength, growing from 4.82 ± 0.02 nm/% measured for 12th order peak at 517 nm to 8.12 ± 0.04 nm/% measured for 7th order peak at 883 nm. These values correspond to roughly 20 % higher sensitivity than silica FBGs exhibit in this spectral range. The gratings in PF-POFs combine the higher strain sensitivity and low-loss operation while maintaining the mechanical advantages of polymer optical fibers. Therefore, they hold a high potential for considerable broadening of polymer optical fiber Bragg gratings application range.
We report on three respiration sensors based on pure optical technologies developed during the FP6 EU project
OFSETH. The developed smart medical textiles can sense elongation up to 3%, while maintaining the stretching
properties of the textile substrates for a good comfort of the patient. The sensors, based on silica and polymer fibre, are
developed for monitoring of patients during MRI examination. The OFSETH harness allows a continuous measurement
of respiration movements while all vitals organs are free for medical staff actions. The sensors were tested in MRI
environment and on healthy adults.
One of the main unsolved issues of under-ground storages for, e.g., CO2, H2, and natural gas is the comprehensive surveillance of these areas with reasonable effort and costs. Conventional sensors (e.g., soil air probes or borehole probes), however, can only be used for punctual or locally limited measurements; further their application can cause structural influences (invasive application).
In this paper, we describe in detail the setup of a CO2 injection soil test field. This test field will be used to enhance and validate an innovative ap-proach for distributed subsurface monitoring of gas storage areas. To the author’s knowledge, this is the first time that, for this purpose, a test field is built in an application relevant scale.
We investigate two real-time strain sensing principles based on the optical time-domain reflectometry
(OTDR) in polymer optical fibres (POF). The first sensing principle uses the increase of the level of backscattered light
in a stretched POF. The second sensing principle uses the effect of losses due to bending.