Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (39) (entfernen)
Referierte Publikation
- nein (39)
Schlagworte
- Computed tomography (5)
- Concrete parameters (4)
- Self-corrosion (4)
- X-ray tomography (4)
- Computertomographie (3)
- Reinforcement (3)
- Coordinate metrology (2)
- Metallographic section (2)
- Microtomography (2)
- Synchrotron radiation (2)
Industrial computed tomography (CT) today is an important method to analyze defects and to measure the geometry of technical products. The measurement capability of industrial CT often depends on the knowledge of the measurement errors being present. Only with this knowledge, effective corrections are possible by manufacturers, or adapted measurement procedures become possible for the customers. Thus, there is the strong need to have adequate reference standards both for the assessment of general dependencies and for the measurement of task-specific effects. Especially the latter are difficult to assess. This paper shows the application of a versatile dismountable workpiece-near reference body for the use with CT. The reference standard was made from a miniaturized cast aluminium (one-)cylinder head. It can be dismounted into four segments, each featuring reference geometries which enable a registration of CT measured and other reference datasets (e.g. from tactile CMM). The reference standard embodies complex freeform surfaces which are a challenging measurement task for CT and other sensors. Here the application of the reference standard is the study of the influence of material mixes. This is realized by adding pieces of other materials which disturb the mono-material measurement.
Results of the application of the reference standard are presented using data from industrial micro-CT systems and CMM reference data. A special emphasis is given on the workflow of the data processing and the data analysis.
Investigations of corrosion on small cathodes in reinforced concrete - observations and suggestions
(2009)
Corrosion of steel reinforcement in concrete exposed to chloride containing environments is a serious
problem in civil engineering practice. The standards and guidelines contain only minimum
requirements regarding concrete quality and concrete cover. In very critical cases, for example the
ingress of chlorides, the application of different coatings is currently the only possibility to protect the
reinforced concrete structures. In this case the modelling of reinforcement corrosion would be more
practical. One sub-project of a DFG-research project (FOR 537) is currently performed at the Federal
Institute for Materials Research and Testing (BAM). Aim of the sub-project is the description of
corrosion propagation and the characterization of the corrosion on specimens with small cathodes by
electrochemical parameters. The electrochemical parameters are determined by suitable
electrochemical measurements, considering concrete parameters as well as different environmental
conditions.
Die Computertomographie (CT) hat sich als dimensionelle Messmethode in der industriellen Produktion etabliert. Durch Messungen an speziellen Prüfkörpern ist es möglich, quantitative Informationen über die metrologischen Eigenschaften dimensioneller Messungen zu erhalten. In dieser Arbeit wird einen Aluminium-Guss-Prüfkörper (120 mm x 90 mm x 60 mm) benutzt, mit dem – in der vorliegender Form – auch der Einfluss von Materialien unterschiedlicher Schwächung auf dimensionelle CT-Messungen untersucht werden kann. Der Prüfkörper ist in vier Segmente zerteilt, so dass auch innenliegende, raue Gussfreiformflächen der taktilen Koordinatenmessung zugänglich sind. Durch adaptierte Rubinkugeln als Referenzstrukturen können die CT-Messdaten in taktile Referenz-Koordinatensysteme überführt werden. Um den Einfluss von Materialien unterschiedlicher Schwächung auf das dimensionelle Messen mit CT zu untersuchen, wurden stärker schwächende ZTA-Störkugeln (Zirconia Toughened Alumina) mit zur Ausrichtung geeigneter Symmetriebrechung in der Nähe von ausgewählten taktilen Messstellen angebracht.
Zur Bewertung der Messabweichungen dienen taktile Referenzmessungen an den ZTA-Kugeln sowie taktile Messungen an den Freiformflächen des Gussteils, wobei durch ein iteratives Antastverfahren eine verbesserte Erfassung der Geometrie auch bei starken lokalen Oberflächenkrümmungen sichergestellt wird.
Phasenkontrastmessungen haben sich als hilfreich bei der
Kantenfindung von Strukturen mit nur geringem Absorptionskontrast erwiesen.
Solche Messungen können besonders gut mit monochromatischer Röntgenstrahlung
hoher räumlicher Kohärenz durchgeführt werden, wie sie bei der Synchrotron-
Computertomographie (SY-CT) benutzt wird. Nachteilig wirken sich allerdings die
Phasenverschiebung des Synchrotronstrahls über das Strahlprofil und damit die
Kantenverbreiterung in den zu untersuchenden Strukturen aus. Daher ist ein
dimensionelles Messen mit normalen Rekonstruktionsverfahren nicht möglich. In
der vorliegenden Arbeit werden neue Filterverfahren zur Korrektur der
Phasenverschiebung unter Beibehaltung des erhöhten Kontrastes bei der
Rekonstruktion angewandt, um ausgewählte einkomponentige Referenzobjekte
hinsichtlich der dimensionellen Messeigenschaften zu untersuchen. Als Referenz
werden rückgeführte Messungen mit taktilen Koordinatenmessmaschinen
herangezogen. Die Untersuchungen wurden im freien Strahl durch Variation des
Abstandes zwischen Objekt und Detektor am Strahlrohr der BAM am Helmholtz-
Zentrum Berlin für Materialien und Energie - Speicherring BESSY II durchgeführt.
Analyzing damages at concrete structures due to physical, chemical, and mechanical exposures need the application of innovative non-destructive testing methods that are able to trace spatial changes of microstructures. Here, the utility of three different crack detection methods for the analysis of computed tomograms of various cementitious building materials is evaluated. Due to the lack of reference samples and standardized image quality evaluation procedures, the results are compared with manually segmented reference data sets. A specific question is how automatic crack detection can be used for the quantitative characterization of damage processes, such as crack length and volume. The crack detection methods have been integrated into a scientific visualization system that allows displaying the tomography images as well as presenting the results.