Filtern
Dokumenttyp
- Vortrag (408) (entfernen)
Sprache
- Englisch (268)
- Deutsch (139)
- Mehrsprachig (1)
Referierte Publikation
- nein (408)
Schlagworte
- Safety (24)
- Hydrogen (22)
- Gefahrgutverpackungen (18)
- Wasserstoff (18)
- Transport (16)
- Ageing (14)
- Drop test (13)
- Lithiumbatterien (13)
- H2Safety@BAM (12)
- Sicherheit (12)
Organisationseinheit der BAM
- 3 Gefahrgutumschließungen; Energiespeicher (408) (entfernen)
Heizöllagerbehälter aus Kunststoffen (z.B. Polyethylen) sind für einen sicheren Betrieb von 30 Jahren, dem Zeitraum der Produkthaftung, ausgelegt. Die Tankhersteller empfehlen zur Gewährleistung der Sicherheit nach Ablauf von 30 Jahren den Ersatz dieser Behälter. Kunststoffe unterliegen im Laufe ihrer Nutzungsdauer der Alterung durch die Veränderung ihrer Eigenschaften. Das Ausmaß der Alterung und die Art des Abbauvorganges hängen im Wesentlichen vom chemischen Abbau des Kunststoffes, der Wanddicke des Behälters und den Umgebungsbedingungen ab. Aufgrund der Komplexität der Alterungsvorgänge sind Aussagen zum Langzeitverhalten bzw. zur Lebensdauer der Heizöllagerbehälter ohne geeignete Langzeitprüfungen problematisch. Bisher liegen keine Untersuchungen zum Langzeitverhalten der Kunststoffe vor, insbesondere nach einer Nutzungsdauer über 20 Jahre. In der BDH-Broschüre: Effiziente Systeme und erneuerbare Energien wird darauf hingewiesen, dass ca. 45 % der Heizöllagerbehälter aus Kunststoffen in Deutschland 26 Jahre und älter sind. Viele dieser Tankanlagen sind zudem noch nie von einem Sachverständigen überprüft worden. Schätzungen gehen davon aus, dass mehr als 10.000.000 Tankanlagen aus Kunststoffen in Deutschland vor 1987 errichtet wurden.
Ziel der Untersuchungen ist, den Schädigungsgrad der Kunststoffe im Vergleich zu den unbelasteten Werkstoffen zu ermitteln. Da die BAM bis Ende der 80-iger Jahre für die Zulassung dieser Behälter zuständig war, sind die Daten über den eingesetzten Werkstoff für den Vergleich noch vorhanden. Der Bundesverband Lagerbehälter e.V. und das Institut für Wärme und Oeltechnik (IWO) befürworten diese Untersuchungen, um eine Überalterung der Tankanlagen zu vermeiden. Diese Überalterung könnte die zukünftige Gefahr für die Heizöltankanlage sein, nicht der Wettbewerb mit anderen Energieformen.
Parameter study for CFD in the bottle – grid resolution plays an important role on the temperature at the specific positions, 2D axi-symetrical calculation is a sufficient solution strategy in regards to the examined particular Problem. The intensity of filling process can be controlled by pressure “User defined function” provided by experiments. Numerical simulation demonstrated feasibility to predict temperature progress during the filling process successfully validated by experiments. The turbulent model k-w SST is the best strategy for the turbulent property calculations. The most intensive turbulent kinetic energy appeared in the middle region of the pressure bottle, the impact of the eddy viscosity on the wall was mostly in the wall region.
Biofuels including ethanol and biodiesel (FAME) represent a renewable fuel alternative to petroleum-derived transport fuels. The aim of this work was to study the interaction between high density polyethylene (HDPE) with permeation barriers in form of polyamide (PA) and fluorination, and biofuels such as E85 (fuel with 85 % ethanol), biodiesel and B10 (heating oil with 10 % biodiesel). 10 l jerrycans made of polyethylene with permeation barrier of PA were filled with E85 and biodiesel and exposed to temperatures of 20 °C and 40 °C for 5 years. Half of the 20 l jerrycans of HDPE for filling with B10 were fluorinated at the inner layer to prevent permeation before the exposure. Tensile properties were determined once a year, and FTIR-spectroscopy was used to evaluate possible changes.
The tensile properties tensile strength and breaking elongation of HDPE jerrycan cuttings with permeation barrier decreased, but not significantly, after immersion in E85, biodiesel and B10. The elasticity modulus of the polyethylene grades was especially reduced during exposure to E85.
The FTIR spectra of HDPE jerrycan cuttings with permeation barrier showed that immersion tests for five years with the test fuels at 20 °C and 40 °C did not lead to a decomposition of the permeation barriers.
Packages for the transport of radioactive material are often equipped with impact limiters consisting of wood. Mostly this wood is encapsulated by steel sheets. The impact limiters are needed to ensure that the transport casks meet the IAEA safety requirements. According to the IAEA safety requirements a package has to withstand consecutively severe mechanical tests followed by a thermal test. The mechanical tests have to produce maximum damage concerning the thermal test. Following this, the impact limiters may have serious pre-damage when the thermal tests begins. The IAEA safety requirements state that during and following the fire test, the specimen shall not be artificially cooled and any combustion of materials of the package shall be permitted to proceed naturally.
Small scale fire tests with wood filled metal drums by BAM and works of the French Institute for Radiological Protection and Nuclear Safety (IRSN) showed that pre-damaged steel encapsulated wooden structures could start smoldering initiated by the thermal test. These processes supply additional energy to the cask which should be considered within the safety assessment of the package.
As not much is known about smoldering processes in encapsulated wooden structures with a reduced oxygen supply the need for a test was identified. To investigate the influence of a smoldering impact limiter concerning the amount of energy supplied to the cask in dependence of the time BAM conducted a large scale impact limiter thermal test. For that, a pre-damaged impact limiter with a diameter of 2,3 m was mounted on a water tank simulating a cask. A complex system of a regulated pump, a heater, a cooler, a slide valve, a flow meter and numerous thermocouples were installed and connected to a control unit to ensure all needed operating conditions.
After a pre-heating compared to typical SNF decay-heat, the 30 min lasting fire phase of the thermal test was started. After that, the expected and initiated smoldering began. The results of the large scale test are presented in this poster. Systematic small scale tests will follow to identify the influence of different parameters, e.g. moisture content and scale effects. The tests took place at BAM Test Site for Technical Safety (TTS) with its various possibilities for mechanical and thermal tests. The results of these tests will have direct influence in the safety assessment of transport cask for the transport of radioactive material.
This presentation focusses on the thermal test of a typical storage container design for the German final storage repository KONRAD. The preparation of the container, the conduction of the fire test itself and results like the temperature evolution and as-sumptions for thermal material properties are shown.
As thermal test final storage containers have to be exposed to a fire of 800 °C (1472 °F) for 1 hour according to the final storage conditions provided by the federal com-pany for radioactive waste disposal (BGE). The here discussed cask contains a steel covered concrete layer of a thickness of 100/150 mm. Heating up concrete is a highly nonlinear process since the vaporization of residual water consumes high amounts of thermal energy and produce vast amounts of steam.
The constantly measured temperatures provide the basis to adjust common models of thermal properties for concrete esp. for FEAs. Finally in a later step this will allow predictions of similar designed container with different sizes.
The paper focuses on the preliminary determination of the bar length and the experimental performance of the 1m-puncture test in compliance with the guidelines of the IAEA under the given boundary conditions. Following aspects have to be considered concerning the determination of an appropriate length of the bar to obtain maximum damage to the specimen: the design of the package, its drop orientation and the impact point as well as a pre-damage of the package resulting from a previous 9m drop test. According to the Regulations the minimum length of the bar is defined as 20 cm, which has to be adapted to the outer surface of the package, especially to packages with large impact limiters.
In this context, two main aspects are important: First, the realisation of a maximum puncture load applied to the package while no other component of the package has contact with the impact target. Second, the reduction of the risk of buckling and maximising the stiffness of the bar by a length which is as short as possible. In order to optimize the bar length, finite element calculations are often done by simulating the global behaviour of the package during the puncture test. The evaluation of the conducted puncture test regarding IAEA compliance is done by analysing deceleration measurements. The paper presents a possible approach to determine the length of the bar and the construction of a form-fitted connection to the target showing various examples of puncture tests.
A preliminary analysis has been presented on the advantages for Mexico to migrate the cargo from trucking to railways. While the approach is highly unrealistic, it describes interesting figures that should animate the interest of Mexico to develop its railway infrastructure. Adverse situations due to the topographic characteristics of the mostly populated area of Mexico. The data presented in this paper suggest that the building of railway infrastructure is economically feasible.