Filtern
Dokumenttyp
- Vortrag (5) (entfernen)
Referierte Publikation
- nein (5) (entfernen)
Schlagworte
- Shrinkage (5) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (5)
Alkali-activated slag materials are known for their high Chloride penetration resistance. This makes them potentially applicable as repair systems for damaged steel-reinforced concrete structures, which are exposed to chloride attack. For this purpose, the influence of the activator composition, i.e. the SiO2 and Na2O concentration of the alkaline solution on a) the compressive strength, b) shrinkage and mass change and c) the resistance against chloride penetration of four alkali-activated slag mortars (AASM) were studied. An ordinary Portland cement-based mortar was used as the reference sample. Increasing SiO2 and Na2O concentrations increased the strength, shrinkage and mass loss of the AASMs. The resistance of the mortars against chloride penetration was evaluated using the non-steady-state migration coefficient Dnssm obtained from NT BUILD 492. The results indicate that the Dnssm is related to differences in the pore solution of the AASMs rather than to differences in their microstructure. An upcoming study of the authors is going to evaluate this hypothesis by the accelerated chloride penetration (diffusion) test.
Shrinkage measurement of miniaturized low temperature co-fired
ceramics (LTCC) samples under load typically leads to a collapsing of
the sample due to the softening of the glassy phase, which hampers
the characterization of shrinkage up to full densification. In practical
sintering processes in contrast, LTCC panels are sintered under axial
loads of up to 1 MPa without lateral shrinkage or collapsing of the
structure. To characterize the shrinkage behavior during such
processes, a measurement setup was developed, which allows for in-situ
thickness shrinkage measurements of practical, large LTCC panels
during pressure-assisted sintering in a sintering press. Using this setup,
the shrinkage behavior of two commercial LTCC tapes (GreenTape 951
and Ceramtape GC) has been measured under loads of up to 1 MPa.
No crushing of the specimens was observed and reproducible
characterization of shrinkage up to full densification has been
performed. Based on comparisons to thermomechanical analyzer
measurements in this and other studies, it is concluded that the in-situ
approach is much better suited for shrinkage characterization of LTCC
under load.
Superplasticizer and shrinkage reducing admixture dosages for microfine cement in grout systems
(2018)
Grouts have numerous applications including crack repair as maintenance in construction industries. Microfine cements are intensively used for high strength mortar and grout products. They are ideal for injection grouting in structural repair. Such grouts should have suitable rheological properties to be injectable, especially those used in repair and rehabilitation. The use of superplasticizers (SP) in these products is thus becoming increasingly crucial to achieve favorable workability and viscosity properties. A difficulty in such grouts is the plastic shrinkage due to finer particles used. It is thus necessary to determine optimum SP and shrinkage reducing admixture (SRA) dosages for a microfine cement based grout. In this study, a saturation dosage was decided from two Polycarboxylate ether (PCE) based SPs in relation to neat cement using slump flow and rheological parameters. A range of grout mixtures was formulated containing micro silica (MS) and fly ash (FA), and tested for suitable rheological and mechanical parameters. Based on the results, a grout mixture with MS and FA was selected to determine optimum SRA content. According to the results, a SP dosage of 3% by weight of neat cement is sufficient to achieve saturation. The grout material including MS and FA can produce comparable properties to neat cement grout. MS is found to improve compressive strength within the range considered, whereas a higher FA content provides favourable rheological properties. Finally, a SRA dosage of 4%, which could reduce the shrinkage by about 43% after 28d days, is determined for the grout system.
Modeling the interactions of creep, shrinkage and damage in a multiphysics simulation of concrete
(2018)
The time dependent, mechanical behavior of concrete is affected by multiple phenomena like creep, shrinkage and damage propagation. The interactions of these processes are supposed to have significant influence on the materials response to external loading. For example it can be observed that the compressive strength of concrete rises with lowering the moisture content [Dahms, 1968].
Most of the constitutive models for finite element methods are designed with just a single phenomena in mind. In multiphysics simulations it is quiet common to use a linear superposition, i.e. additive decomposition of the total strain into elastic shrinkage, creep or thermal strains.
In this paper, the interactions of creep, shrinkage and damage models are investigated, in particular for cases where the assumption of linear superposition is questionable. A gradient enhanced damage model proposed by [Peerlings et al., 1996] is employed. Creep is modeled as a Kelvin chain as described in [Jirásek and Bažant, 2001]. Shrinkage is simulated by using two different approaches. The first model simulates shrinkage as an additional moisture dependent strain component. In the second model, shrinkage is simulated as a moisture dependent pore pressure applied to the solid bulk.
The impact of model interactions will be discussed with a focus on simulating the influence of the moisture content on the macroscopic strength. The model is validated by comparison to experimental data.
Die geringe Zugfestigkeit von zementgebundenen Materialien kann durch die Zugabe von Fasern maßgeblich verbessert werden. Ziel eines gemeinsamen Verbundprojekts mit einem Industriepartner war die Erhöhung der Leistungsfähigkeit von kurzen Polymer- und Carbonfasern durch eine Verbesserung des Verbundes zwischen Faseroberfläche und Zementsteinmatrix.
Von der IONYS AG wurde dazu eine spezielle Funktionalisierung entwickelt, die über eine Hydrophilisierung der Faseroberfläche eine chemische Anbindung an die Zementsteinmatrix gewährleistet. Aufgabe der BAM war es, die Effizienz der neuen Beschichtung bezüglich der Erhöhung der Nachrissbiegezugfestigkeit und der Reduzierung der Schwindrissbildung während der Erhärtungsphase zu quantifizieren. Die Ergebnisse zeigen, dass die Funktionalisierung die Neigung zur Schwindrissbildung für die Carbonfasern und in noch stärkerem Maße für die Polymerfasern reduziert.
Eine Erhöhung der Nachrissbiegezugfestigkeit konnte dagegen nur für die deutlich steiferen Carbonfasern nachgewiesen werden.