Filtern
Dokumenttyp
- Vortrag (10) (entfernen)
Sprache
- Englisch (10)
Referierte Publikation
- nein (10) (entfernen)
Schlagworte
- E. coli (10) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (10)
Near Ambient Pressure XPS opens up a new world of possibilities for measurements with XPS. While there are examples where NAP-XPS has been used to study electrochemical processes and heterogeneous catalysis, little attention has been paid to its potential use in biological materials. Until now, bacteria have only been characterised with conventional XPS, which requires tedious sample preparation usually involving freeze drying, a treatment that may degrade biological sample constituents. By studying biological samples in their native wet states, new insight about composition, absorption and transport of drugs through cell membranes and extracellular polymeric substance (EPS) layers can be obtained. Both artificial model-films of exopolysaccharides and biofilms of Escherichia Coli have been characterised at pressures ranging from ultra-high vacuum to 15 mbar by using SPECS’ EnviroESCA NAP-XPS instrument and conventional XPS. By applying antimicrobials to model biofilms, some of which are known to be resistant towards the antimicrobial in question, the distribution of antimicrobials in biofilms has been studied. Capabilities and limitations of the approach will be discussed.
A drawback for X-ray photoelectron spectroscopy is that the measurements must be performed under ultra-high vacuum, which limits the type of samples which can be studied. However, by applying a differentially pumped aperture positioned close to the surface, even wet samples can be measured at near ambient pressure while the energy analyser is still under ultra-high vacuum, as illustrated below. Successful XPS-measurements with pressure up to 30 mbar have been reported using this approach, which opens up a new world of possibilities for ambient pressure measurements with XPS.
While there are examples where NAP-XPS has been used to study electrochemical processes and heterogeneous catalysis, little attention has been paid to its potential use in biological materials. Until now, bacteria have only been characterised with conventional XPS, which requires tedious sample preparation usually involving freeze drying, a treatment that may degrade biological sample constituents. By studying biological samples in their native wet states, new insight about composition, absorption and transport of drugs through cell membranes and extracellular polymeric substance (EPS) layers can be obtained.
Both artificial model-films of exopolysaccharides and biofilms of Escherichia Coli have been characterised at pressures ranging from ultra-high vacuum to 15 mbar by using SPECS’ EnviroESCA NAP-XPS instrument and conventional XPS. By applying antimicrobials to model biofilms, some of which are known to be resistant towards the antimicrobial in question, the distribution of antimicrobials in biofilms has been studied. Measurement capabilities and limitations of the approach will be discussed.
The XPS information depth of approximately 10 nm is in the same size range as the outer membrane of the gram-negative bacteria, which makes XPS a suitable tool for determining the elemental composition of the bacterial surface and monitor changes caused by outer stress like dehydration or exposure to antimicrobials. However, bacteria are inherently in a hydrated state, and therefore only compatible to ultra-high vacuum after extensive sample preparation, which may degrade the sample constituents. This issue is addressed by the development of near-ambient pressure (NAP)-XPS, which enables bacteria and biofilms to be characterised in their native wet state. Artificial biofilms, bacteria and biofilms of Escherichia coli have been characterised with the laboratory NAP-XPS instrument EnviroESCA from SPECS GmbH, at pressures ranging from high vacuum to 12 mbar, and in both humid and dry environment. By studying biological samples in their native wet state, new insight about composition and transport of drugs through cell membranes and the extracellular polymeric substance (EPS) of biofilms can be obtained. In this contribution, the latest progress on biofilm characterisation by NAP-XPS will be presented, and measurement capabilities and limitations will be discussed.
X-ray photoelectron spectroscopy (XPS) provides elemental and chemical information from the outermost ~10 nm of the sample surface. This is in the same order of magnitude as the thickness of the outer bacterial membrane of gram-negative bacteria, as well as outer membrane molecules as exopolysaccharides and lipopolysaccharides, commonly attached to the cell surface. With the development of near-ambient pressure (NAP)-XPS, bacteria can be analysed with minimal sample preparation.
EnviroESCA is a laboratory based NAP-XPS instrument, equipped with a monochromated Al Kα radiation source and a differentially pumped energy analyser connected to an exchangeable sample environment. It allows for measurements in various gas-atmospheres, including water vapor, which makes it possible to characterise bacteria and other biological samples close to their natural, hydrated state. Artificial model-biofilms of exopolysaccharides, planktonic Pseudomonas Fluorescens and biofilms of Escherichia Coli have been characterised in hydrated and dried state.
High-resolution XPS-spectra from carbon, oxygen, nitrogen and phosphorous can be assigned to carbohydrates, lipids and proteins in general agreement with literature. Especially the carbon 1s peak is of interest. A series of measurements of an E. coli biofilm from 11 mbar in humid environment to 1 mbar air reveal changes in the C1s peak, which suggests that the bacterial surface undergo substantial Change.
Bacterial samples are typically freeze dried or cryo-prepared prior to XPS analysis to allow for measurements in ultra-high vacuum (UHV). The sample environment in the near-ambient pressure (NAP) XPS instrument EnviroESCA allows for measurements in up to 15 mbar water vapor, thus, sample preparation is no longer restricted to UHV-compatible techniques. For instance, biofilms grown in medium can be transferred directly from the medium to the measurements chamber, maintaining a humid environment throughout the measurements. Considering the complexity of bacterial samples, sample preparation must be carefully considered in order to obtain meaningful and reproducible results.
In this talk, various strategies for sample preparation of bacteria and biofilms for NAP-XPS measurements will be discussed. Model systems of planktonic bacteria, artificial biofilms resembling the exopolysaccharide matrix and biofilms have been characterised in various conditions. The stability and homogeneity of the samples was assessed by monitoring the C1s core level peak at different sample locations. The quality of the XPS-spectra is also influenced by the gas environment, which will be exemplified by core level spectra of P. Fluorescens acquired in air, water vapor and ultra-high vacuum.
Using nanofiber-like cell appendages, secreted proteins and sugars, bacteria can establish initial surface contact followed by irreversible adhesion and the formation of multicellular biofilms. Here, the stabilizing extracellular biofilm matrix together with physiological changes on the single cell level leads to an increased resilience towards harsh environmental conditions, antimicrobials, the host immune response and established cleaning procedures. Persistent microbial adhesion on e.g., medical implants, in water supply networks or food-processing industry is often associated with chronic inflammation, nosocomial and foodborne infections, enhanced biofouling and product contamination. To prevent persistent microbial colonization, antibacterial surface strategies often target the initial steps of biofilm formation and impede adhesion of single cells before a mature biofilm is being formed. While chemical coatings have been widely used, their restricted biocompatibility for eukaryotic cells and attenuated antibacterial-effects due to compound release limit their areas of application and alternative strategies focus on modified surfaces topographies to impede bacterial adhesion. In this work, we used ns-UV laser treatment (wavelength 248 nm and a pulse duration of 20 ns) to generate laser-induced periodic surface structures (LIPSS) with different submicrometric periods ranging from ~210 to ~610 nm on commercial poly(ethylene terephthalate) (PET) foils. Following structurally and chemically analyses, PET samples were subjected to bacterial colonization studies with Escherichia coli TG1, a bacterial test strain with a strong biofilm formation capacity due to the formation of nanofiber-like cell-appendages (pili). Bacterial adhesion tests revealed that E. coli repellence decisively depends on the spatial periods of the LIPSS with the strongest reduction (~91%) in cell adhesion observed for LIPSS periods of 214 nm. Scanning electron microscopy and additional biofilm studies using a pili-deficient E. coli TG1 strain revealed the importance of extracellular appendages in the bacterial repellence observed here, thus, pointing out new antibiotics-free strategies for antibacterial surfaces by impeding nanofiber-mediated bacterial adhesion.